ISO 11359-3:2002

Plastics — Thermomechanical analysis (TMA) — Part 3: Determination of penetration temperature

This part of ISO 11359 specifies a method for the determination of the penetration temperature of thermoplastics using thermomechanical analysis. NOTE This method can also be used to measure the softening temperature.

Plastiques — Analyse thermomécanique (TMA) — Partie 3: Détermination de la température de pénétration

General Information

• Status: Withdrawn
• Publication Date: 23-Oct-2002
• Withdrawal Date: 23-Oct-2002
• ICS: 83.080.01 - Plastics in general
• Technical Committee: ISO/TC 61/SC 5 - Physical-chemical properties
• Drafting Committee: ISO/TC 61/SC 5/WG 8 - Thermal analysis
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 05-Feb-2019

Relations

• Revised: ISO 11359-3:2019 - Plastics — Thermomechanical analysis (TMA) — Part 3: Determination of penetration temperature
• Effective Date: 15-Dec-2017
• Consolidated By: ISO 5173:2009/Amd 1:2011 - Destructive tests on welds in metallic materials — Bend tests — Amendment 1
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11359-3
First edition
2002-10-01
Plastics — Thermomechanical analysis
(TMA) —
Part 3:
Determination of penetration temperature
Plastiques — Analyse thermomécanique (TMA) —
Partie 3: Détermination de la température de pénétration

Reference number
ISO 11359-3:2002(E)
© ISO 2002

---------------------- Page: 1 ----------------------
ISO 11359-3:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2002 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11359-3:2002(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Test specimen . 2
7 Procedure . 2
8 Expression of results . 3
9 Precision . 3
10 Test report . 3
Bibliography. 5
©
ISO 2002 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 11359-3:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 11359 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 11359-3 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 5, Physical-chemical properties.
ISO 11359 consists of the following parts, under the general title Plastics — Thermomechanical analysis (TMA):
— Part 1: General principles
— Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
— Part 3: Determination of penetration temperature
©
iv ISO 2002 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 11359-3:2002(E)
Plastics — Thermomechanical analysis (TMA) —
Part 3:
Determination of penetration temperature
1 Scope
This part of ISO 11359 specifies a method for the determination of the penetration temperature of thermoplastics
using thermomechanical analysis.
NOTE This method can also be used to measure the softening temperature.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 11359. For dated references, subsequent amendments to,
...