ISO 22242:2005

Road construction and road maintenance machinery and equipment — Basic types — Identification and description

ISO 22242:2005 identifies and describes machinery and equipment used in the construction and maintenance of traffic routes, roads, highways, runways, aprons, etc. It is applicable to those specialized machines/equipment intended for pavement construction and road maintenance. It does not define terms, and its figures represent only a general view or outline.

Machines et matériels pour la construction et l'entretien des routes — Principaux types — Dénomination et description

General Information

• Status: Published
• Publication Date: 21-Sep-2005
• ICS: 93.080.10 - Road construction
• Technical Committee: ISO/TC 195 - Building construction machinery and equipment
• Drafting Committee: ISO/TC 195/WG 5 - Road construction and maintenance equipment - Terminology and commercial specifications
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 31-May-2024

Relations

• Amended By: ISO 22242:2005/Amd 1:2013 - Road construction and road maintenance machinery and equipment — Basic types — Identification and description — Amendment 1
• Effective Date: 25-Apr-2020

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 22242
First edition
2005-09-15

Road construction and road maintenance
machinery and equipment — Basic
types — Identification and description
Machines et matériels pour la construction et l'entretien des routes —
Principaux types — Dénomination et description




Reference number
ISO 22242:2005(E)
©
ISO 2005

---------------------- Page: 1 ----------------------
ISO 22242:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 22242:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Machines and equipment for road construction and maintenance. 2
2.1 Soil stabilization machinery and equipment. 2
2.2 Machines and equipment for bituminous binders . 4
2.3 Machines and equipment for asphalt mix production . 7
2.4 Machines and equipment for concrete asphalt pavement construction . 8
2.5 Machines and equipment for concrete pavement construction . 10
2.6 Machines and equipment for finishing road works. 13
2.7 Road surface cleaning machines. 14
2.8 Machines and equipment for removal of undesired vegetation . 16
2.9 Machines and equipment for road winter maintenance . 18
2.10 Machines and equipment for road repairs . 19
Bibliography . 23

© ISO 2005 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 22242:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft Internat
...