ISO/FDIS 15015

Plastics — Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA) — Requirements and test methods

ISO 15015:2011 specifies the requirements and test methods for solid flat extruded sheets of impact-modified acrylonitrile-styrene copolymer materials: acrylonitrile-butadiene-styrene (ABS), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) (commonly known as AES) and acrylonitrile-styrene-acrylate (ASA), without fillers or reinforcing materials. This International Standard also applies to ABS, AEPDS and ASA sheet in rolled form. It applies only to thicknesses from 0,25 mm to 20,0 mm.

Plastiques — Plaques extrudées en copolymères d'acrylonitrile-styrène modifiés choc (ABS, AEPDS ou ASA) — Exigences et méthodes d'essai

L'ISO 15015:2011 spécifie les exigences et les méthodes d'essai pour les plaques extrudées compactes et planes, en copolymères d'acrylonitrile-styrène modifiés choc: acrylonitrile-butadiène-styrène (ABS), acrylonitrile-(éthylène-propylène-diène)-styrène (AEPDS ou appelé AES sur le marché) et d'acrylonitrile-styrène-acrylate (ASA), sans charges ou renforts. L'ISO 15015:2011 s'applique également aux plaques en ABS, en AEPDS ou en ASA sous forme de rouleaux. Elle s'applique uniquement aux plaques de 0,25 mm à 20,0 mm d'épaisseur.

General Information

• Status: Not Published
• ICS: 83.140.10 - Films and sheets
• Technical Committee: ISO/TC 61/SC 11 - Products
• Drafting Committee: ISO/TC 61/SC 11/WG 3 - Plastics films and sheeting
• Current Stage: 5020 - FDIS ballot initiated: 2 months. Proof sent to secretariat
• Start Date: 26-Aug-2025
• Completion Date: 26-Aug-2025

Relations

• Revises: ISO 15015:2011 - Plastics — Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA) — Requirements and test methods
• Effective Date: 07-Jan-2025

Standards Content (Sample)

FINAL DRAFT
International
Standard
ISO/TC 61/SC 11
Plastics — Extruded sheets of
Secretariat: JISC
impact-modified acrylonitrile-
Voting begins on:
styrene copolymers (ABS, AEPDS
2025-08-26
and ASA) — Requirements and test
Voting terminates on:
methods
2025-10-21
Plastiques — Plaques extrudées en copolymères d'acrylonitrile-
styrène modifiés choc (ABS, AEPDS ou ASA) — Exigences et
méthodes d'essai
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
FINAL DRAFT
International
Standard
ISO/TC 61/SC 11
Plastics — Extruded sheets of impact-
Secretariat: JISC
modified acrylonitrile-styrene
Voting begins on:
copolymers (ABS, AEPDS and ASA) —
Requirements and test methods
Voting terminates on:
Plastiques — Plaques extrudées en copolymères d'acrylonitrile-
styrène modifiés choc (ABS, AEPDS ou ASA) — Exigences et
méthodes d'essai
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2025
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland Reference number
ii
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Material. 2
5 Requirements . 2
5.1 Appearance .2
5.2 Dimensional tolerances .2
5.2.1 Thickness .2
5.2.2 Length and width . .2
5.2.3 Rectangularity .3
5.2.4 Bow of sheets in rolled form .3
5.3 Properties .3
5.3.1 Mechanical and thermal properties .3
5.3.2 Behaviour on heating .4
5.3.3 Physiological behaviour .4
6 Test methods . 5
6.1 Test specimens.5
6.1.1 Preparation of test specimens .5
6.1.2 Conditioning .5
6.1.3 Test conditions .5
6.2 Delivery condition .5
6.3 Appearance .5
6.4 Dimensions .5
6.4.1 Thickness,h .5
6.4.2 Length, l, and width, b . . .6
6.4.3 Rectangularity .6
6.4.4 Bow of sheets in rolled form .6
6.5 Density .6
6.6 Mechanical properties .6
6.6.1 Tensile stress at yield, σ .6
y
6.6.2 Modulus of elasticity in tension,E .6
t
6.6.3 Charpy impact strength of unnotched specimens,a .6
cu
6.6.4 Charpy impact strength of notched specimens,a .6
cn
6.6.5 Ball indentation hardness .6
6.6.6 Melt mass-flow rate (MFR) . .6
6.7 Thermal properties .7
6.7.1 Vicat softening temperature .7
6.7.2 Determination of shrinkage on heating .7
7 Designation . 8
7.1 Example for ABS sheets .8
7.2 Example for ASA sheets in rolled form .9
8 Marking . . 9
Annex A (informative) Additional guide values . 10
Bibliography .11

iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC
249, Plastics, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna
Agreement).
This third edition cancels and replaces the second edition (ISO 15015:2011), which has been technically revised
The main changes are as follows:
— Clause 3, Terms and definitions, has been added, and subsequent clauses have been renumbered;
— Formula (2) has been deleted because the tolerance for the entire sheets delivery would be higher than
for each individual sheet, and subsequent formulae have been renumbered;
— in the
...

ISO/DISFDIS 15015:2024(en)
ISO/TC 61/SC 11
Secretariat: JISC
Date: 2025-05-02
Plastics — Extruded sheets of impact-modified acrylonitrile-styrene
copolymers (ABS, AEPDS and ASA) — Requirements and test
methods
Plastiques — Plaques extrudées en copolymères d'acrylonitrile-styrène modifiés choc (ABS, AEPDS ou ASA) —
Exigences et méthodes d'essai
FDIS stage
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO'sISO’s member body in the country of the requester.
ISO Copyright Officecopyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Email: [e-mail]
E-mail: [e-mail]
Website: www.iso.orgwww.iso.org
Published in Switzerland.
ii
ISO/DISFDIS 15015:20242025(en)
Contents Page
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Material . 2
5 Requirements . 2
6 Test methods . 5
7 Designation . 9
8 Marking . 10
Annex A (informative) Additional guide values . 11
Bibliography . 12

Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Material . 2
5 Requirements . 2
6 Test methods . 5
7 Designation . 8
8 Marking . 9
Annex A (informative) Additional guide values . 10
Bibliography . 11

iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s)
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents.www.iso.org/patents. ISO shall not be held responsible for identifying any or all such
patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.htmlwww.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products, in
collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC 249,
Plastics, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna
Agreement).
This third edition cancels and replaces the second edition (ISO 15015:2011), which has been technically
revised
The main changes are as follows:
— — in 5.2.1 3, Terms and definitions, has been added, and subsequent clauses have been renumbered;
— Formula (2) washas been deleted because the tolerance for the entire sheets delivery would be higher
than for each individual sheet, and subsequent formulae have been renumbered;
— — in the title of Table 2,Table 2, ISO 291 washas been added;
— — in Tables 2Tables 2 and 33, the mechanical properties 50 % impact-failure energy, E , at h = 4 mm
50 n
werehave been deleted as it is not used;
— — 6.6.5 waspuncture impace behaviour (former 5.6.5) has been deleted as it is not used.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
DRAFT International Standard ISO/DIS 15015:2024(en)

Plastics — Extruded sheets of impact-modified acrylonitrile-styrene
copolymers (ABS, AEPDS and ASA) — Requirements and test methods
Plastics — Extruded sheets of impact-modified acrylonitrile-styrene
copolymers (ABS, AEPDS and ASA) — Requirements and test methods
1 Scope
This document specifies the requirements and test methods for solid flat extruded sheets of impact-modified
acrylonitrile-styrene copolymer materials:
— — acrylonitrile-butadiene-styrene (ABS),
— — acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) (commonly known as AES), and
— — acrylonitrile-styrene-acrylate (ASA), without fillers or reinforcing materials.
This document also applies to ABS, AEPDS and ASA sheet in rolled form. It applies only to thicknesses from
0,25 mm to 20,0 mm.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 179--1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179--2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 306, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 527--2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion
plastics
ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of
thermoplastics — Part 1: Standard method
ISO 11501, Plastics — Film and sheeting — Determination of dimensional change on heating
ISO 1183 (all parts), Plastics — Methods for determining the density of non-cellular plastics
ISO 2039--1, Plastics — Determination of hardness — Part 1: Ball indentation method
ISO 19062-1, Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1:
Designation system and basis for specifications
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 11501, Plastics — Film and sheeting — Determination of dimensional change on heating
ISO 19062-1, Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials — Part 1:
Designation system and basis for specifications
ISO 19065-1, Plastics -— Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene
(AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials -— Part
1: Designation system and basis for specifications
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— — ISO Online browsing platform: available at https://www.iso.org/obphttps://www.iso.org/obp
— — IEC Electropedia: available at https://www.electropedia.org/https://www.electropedia.org/
4 Material
Sheets shall be made of either ABS extrusion materials as defined in ISO 2580 19062-1 or AEPDS (AES) or ASA
extrusion materials as defined in ISO 6402 19065-1, without fillers or reinforcing materials. The extrusion
materials can contain additives such as processing aids, stabilizers, flame-protective agents and colorants.
Compounds and additives of unknown identity shall not be used.
NOTE Legal conditions might necessitate a specific choice of extrusion material (see 5.3.3).5.3.3).
5 Requirements
5.1 Appearance
Sheets shall be substantially free from bubbles, voids, cracks, visible impurities and other defects which would
make them unfit for the intended use. Surfaces shall be substantially smooth, if not embossed, and free from
grooves, sink marks or damage. Colorants shall be homogeneously distributed throughout the material. Slight
colour variations due to variations in the extrusion compound or processing conditions are admissible. The
exact extent of variations in any of the above, as well as gloss level specifications, if required, shall be agreed
between the interested parties. Sheets shall be examined in accordance with 6.3.6.3.
5.2 Dimensional tolerances
5.2.1 Thickness
Within any delivery of sheets, the maximum thickness variation from the nominal value, Δh , in millimetres,
shall satisfy the requirement given as Formula (1):Error! Reference source not found.:
|Δh | ⩽≤ (0,03 mm + 0,04 × h )
1 n
(1)
where h is the nominal sheet thickness, in millimetres.
n
ISO/DISFDIS 15015:20242025(en)
5.2.2 Length and width
The nominal length, l , and nominal width, b , of sheets shall be as agreed between the interested parties.
n n
Unless agreed differently, the length shall be in the direction of extrusion.
For any individual sheet selected at random from any delivery, the tolerances on length and width shall be in
accordance with Table 1.Table 1. Testing shall be in accordance with 6.4.2.6.4.2.
Table 1 — Tolerances on length and width of sheets
Values in millimetres
Tolerances
Nominal dimension
Dn
Length Width
3 2
+3 +2
D ⩽ 1 000
n
−1 −1
1 1
3 3
−3 −3
310 l +3 × 10  × 𝑙 210 b +2 × 10  × 𝑏
n n
n n
D > 1 000
n
−1 −1
1 1
For rolled sheets, the minimum length shall be the nominal length.
5.2.3 Rectangularity
For any individual sheet selected at random from any delivery, the rectangularity tolerance, expressed as the
difference in length of the diagonals, |d − d | (see Figure 1),Error! Reference source not found.), shall
1 2
satisfy the requirement given as Formula (2):Error! Reference source not found.:
–3 2 2
|d − d | ⩽≤ 2 × 10 × √(l + b )
1 2 n n
(2)
Figure 1 — Difference in length of diagonals, |d − d |
1 2
Testing shall be in accordance with 6.4.3.6.4.3.
5.2.4 Bow of sheets in rolled form
For sheets in rolled form, a maximum bow of 20 mm in a 10 m length is permissible. Testing shall be in
accordance with 5.4.4. 6.4.4.
...

PROJET FINAL
Norme
internationale
ISO/TC 61/SC 11
Plastiques — Plaques extrudées en
Secrétariat: JISC
copolymères d'acrylonitrile-styrène
Début de vote:
modifiés choc (ABS, AEPDS ou ASA)
2025-08-26
— Exigences et méthodes d'essai
Vote clos le:
2025-10-21
Plastics — Extruded sheets of impact-modified acrylonitrile-
styrene copolymers (ABS, AEPDS and ASA) — Requirements and
test methods
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
Numéro de référence
PROJET FINAL
Norme
internationale
ISO/TC 61/SC 11
Plastiques — Plaques extrudées en
Secrétariat: JISC
copolymères d'acrylonitrile-styrène
Début de vote:
modifiés choc (ABS, AEPDS ou ASA)
2025-08-26
— Exigences et méthodes d'essai
Vote clos le:
2025-10-21
Plastics — Extruded sheets of impact-modified acrylonitrile-
styrene copolymers (ABS, AEPDS and ASA) — Requirements and
test methods
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
© ISO 2025 INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
NORMES POUVANT
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: [phone]
E-mail: [e-mail]
Web: www.iso.org
Publié en Suisse Numéro de référence
ii
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Matière . . 2
5 Exigences . 2
5.1 Aspect .2
5.2 Tolérances dimensionnelles .2
5.2.1 Épaisseur .2
5.2.2 Longueur et largeur .2
5.2.3 Rectangularité .3
5.2.4 Courbure des plaques en rouleau .3
5.3 Propriétés .3
5.3.1 Propriétés mécaniques et thermiques .3
5.3.2 Comportement après chauffage .4
5.3.3 Comportement physiologique .4
6 Méthodes d'essai . 5
6.1 Éprouvettes pour essai .5
6.1.1 Préparation des éprouvettes .5
6.1.2 Conditionnement .5
6.1.3 Conditions d'essai .5
6.2 Conditions de livraison .5
6.3 Aspect .5
6.4 Dimensions .5
6.4.1 Épaisseur, h.5
6.4.2 Longueur, l, et largeur, b . .6
6.4.3 Rectangularité .6
6.4.4 Courbure des plaques en rouleau .6
6.5 Masse volumique .6
6.6 Propriétés mécaniques .6
6.6.1 Contrainte en traction au seuil d'écoulement, σ .6
y
6.6.2 Module d'élasticité en traction, E .6
t
6.6.3 Résistance au choc Charpy sur éprouvettes non entaillées, a .6
cu
6.6.4 Résistance au choc Charpy sur éprouvettes entaillées, a .6
cn
6.6.5 Dureté à la bille par pénétration .7
6.6.6 Indice de fluidité à chaud en masse (MFR) .7
6.7 Propriétés thermiques .7
6.7.1 Température de ramollissement Vicat .7
6.7.2 Détermination du retrait après chauffage .7
7 Désignation . 8
7.1 Exemple de désignation pour plaques ABS .8
7.2 Exemple de désignation pour plaques ASA en rouleau . .9
8 Marquage . 9
Annexe A (informative) Valeurs indicatives additionnelles .10
Bibliographie .11

iii
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux
de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général
confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L’ISO attire l’attention sur le fait que la mise en application du présent document peut entraîner l’utilisation
d’un ou de plusieurs brevets. L’ISO ne prend pas position quant à la preuve, à la validité et à l’applicabilité de
tout droit de brevet revendiqué à cet égard. À la date de publication du présent document, l’ISO n’avait pas
reçu notification qu’un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois,
il y a lieu d’avertir les responsables de la mise en application du présent document que des informations
plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à l’adresse
www.iso.org/brevets. L’ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou partie de
tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de
l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir le lien suivant www.iso.org/iso/foreword.html.
Le présent document a été élaboré par le comité technique ISO/TC 61, Plastiques, sous-comité SC 11, Produits,
en collaboration avec le comité technique CEN/TC 249, Plastiques, du Comité européen de normalisation
(CEN) conformément à l’Accord de coopération technique entre l’ISO et le CEN (Accord de Vienne).
Cette troisième édition annule et remplace la deuxième édition (ISO 15015:2011), qui a fait l’objet d’une
révi
...