Slotted headless screws with shank

ISO 2342:2003 specifies the characteristics of slotted headless screws with shank with threads from M1 up to and including M10.

Vis sans tête fendues, à fût

L'ISO 2342:2003 spécifie les caractéristiques des vis sans tête fendues, à fût, de filetage M1 à M10 inclus.

General Information

Status
Published
Publication Date
04-Dec-2003
Current Stage
9020 - International Standard under periodical review
Start Date
15-Jan-2023
Completion Date
15-Jan-2023
Ref Project

Relations

Buy Standard

Standard
ISO 2342:2003 - Slotted headless screws with shank
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 2342:2003 - Vis sans tete fendues, a fut
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 2342
Second edition
2003-12-01
Corrected version
2004-06-01
Slotted headless screws with shank
Vis sans tête fendues, à fût
Reference number
ISO 2342:2003(E)
ISO 2003
---------------------- Page: 1 ----------------------
ISO 2342:2003(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall

not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the

unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

© ISO 2003

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii ISO 2003 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 2342:2003(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International

Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 2342 was prepared by Technical Committee ISO/TC 2, Fasteners.

This second edition cancels and replaces the first edition (ISO 2342:1972), which has been technically revised.

In this corrected version of ISO 2342:2003 the following change has been incorporated:

page 2: the dimension ∅ d on Figure 1 has been corrected.
ISO 2003 – All rights reserved iii
---------------------- Page: 3 ----------------------
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 2342:2003(E)
Slotted headless screws with shank
1Scope

This International Standard specifies the characteristics of slotted headless screws with shank with threads

from M1 up to and including M10.

If, in special cases, specifications other than those listed in this International Standard are required, they should

be selected from existing International Standards, e.g. ISO 261, ISO 898-5, ISO 965-2, ISO 3506-3, ISO 8839

and ISO 4759-1.
2 Normative references

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced docum

...

NORME ISO
INTERNATIONALE 2342
Deuxième édition
2003-12-01
Vis sans tête fendues, à fût
Slotted headless screws with shank
Numéro de référence
ISO 2342:2003(F)
ISO 2003
---------------------- Page: 1 ----------------------
ISO 2342:2003(F)
PDF — Exonération de responsabilité

Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier

peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence

autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées

acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute

responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.

Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info du

fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation

de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer

le Secrétariat central à l'adresse donnée ci-dessous.
© ISO 2003

Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous

quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit

de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.

ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii ISO 2003 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 2342:2003(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de

normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée

aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du

comité technique créé à cet effet. Les organisations internationales, gouvernementales et non

gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec la

Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.

Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,

Partie 2.

La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes

internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur

publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres

votants.

L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de droits

de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne pas avoir

identifié de tels droits de propriété et averti de leur existence.

L'ISO 2342 a été élaborée par le comité technique ISO/TC 2, Éléments de fixation.

Cette deuxième édition annule et remplace la première édition (ISO 2342:1972), dont elle constitue une

révision technique.
ISO 2003 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 2342:2003(F)
Vis sans tête fendues, à fût
1 Domaine d'application

La présente Norme internationale spécifie les caractéristiques des vis sans tête fendues, à fût, de filetage M1 à

M10 inclus.

Si, dans des cas particuliers, des spécifications autres que celles figurant dans la présente Norme

internationale sont requises, il est recommandé de les prendre dans les Normes internationales existantes, par

exemple ISO 261, ISO 898-5, ISO 965-2, ISO 3506-3, ISO 8839 et ISO 4759-1.
2Références normatives

Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les

références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du

document de référence s'applique (y compris les éventuels amendements).
ISO
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.