Camera shutters — Timing — General definition and mechanical shutter measurements

This document provides a uniform basis for determining the exposure times for all types of shutters used in still cameras and contains suitable definitions of the terms used. It specifies the exposure-time markings for all types of shutters and their tolerances. The characteristics of all types of mechanical shutters, which are mounted in still cameras and affect the control of exposure, motion-stopping ability and synchronization with a photoflash light source are also defined. The tolerances specified are the target values for the shutter performance that can be expected to give good results. They are not intended for application as a general inspection standard in controlling the performance of mechanical shutters, since tolerances may vary with the feature and price class of camera tested. Test methods are described for routine manufacturing testing and quality control. These test methods require access to the focal plane of the camera and can therefore not be applied to assembled digital still cameras.

Obturateurs d'appareils photographiques — Durée d'exposition — Définition générale et mesurages d'obturateur mécanique

Zaklopi na kamerah - Zaklopni časi - Splošna opredelitev in meritve mehanskih zaklopov

Ta dokument ponuja enotno osnovo za določanje časa osvetlitve za vse vrste zaklopov, ki se uporabljajo v fotoaparatih, in vsebuje ustrezne opredelitve uporabljenih izrazov.
Določa oznake za čas osvetlitve za vse vrste zaklopov in njihove tolerance.
Opredeljuje tudi značilnosti vseh vrst mehanskih zaklopov, ki so nameščeni v fotoaparatih in vplivajo na nadzor osvetlitve, sposobnost zaustavljanja gibanja ter sinhronizacijo z bliskavico.
Dovoljena odstopanja so ciljne vrednosti za delovanje zaklopa, od katerega se pričakuje, da bo dal dobre rezultate. Namen ni uporaba kot splošni standard za nadzor delovanja mehanskih zaklopov, saj se odstopanja lahko razlikujejo glede na lastnosti in cenovni razred preskušenih fotoaparatov.
Opisane so preskusne metode za rutinsko preskušanje v proizvodnji in nadzor kakovosti. Te preskusne metode zahtevajo dostop do goriščne ravnine fotoaparata, zato jih ni mogoče uporabiti za sestavljene digitalne fotoaparate.

General Information

Status
Published
Publication Date
31-Mar-2019
Current Stage
9093 - International Standard confirmed
Completion Date
17-Jun-2024

Relations

Buy Standard

Standard
ISO 516:2022
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 516:2019 - Camera shutters — Timing — General definition and mechanical shutter measurements Released:1. 04. 2019
English language
22 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 516:2019 - Camera shutters -- Timing -- General definition and mechanical shutter measurements
English language
22 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 516:2022
01-oktober-2022
Nadomešča:
SIST ISO 516:2011
Zaklopi na kamerah - Zaklopni časi - Splošna opredelitev in meritve mehanskih
zaklopov
Camera shutters — Timing — General definition and mechanical shutter measurements
Obturateurs d'appareils photographiques — Durée d'exposition — Définition générale
et mesurages d'obturateur mécanique
Ta slovenski standard je istoveten z: ISO 516:2019
ICS:
37.040.10 Fotografska oprema. Photographic equipment.
Projektorji Projectors
SIST ISO 516:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 516:2022

---------------------- Page: 2 ----------------------
SIST ISO 516:2022
INTERNATIONAL ISO
STANDARD 516
Fourth edition
2019-04
Camera shutters — Timing — General
definition and mechanical shutter
measurements
Obturateurs d'appareils photographiques — Durée d'exposition —
Définition générale et mesurages d'obturateur mécanique
Reference number
ISO 516:2019(E)
©
ISO 2019

---------------------- Page: 3 ----------------------
SIST ISO 516:2022
ISO 516:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 516:2022
ISO 516:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 4
5 Required characteristics and their tolerances . 5
5.1 Exposure time . 5
5.1.1 Exposure time marking . 6
5.1.2 Tolerances . 6
5.2 Delay time . 6
5.2.1 Front shutters . 6
5.2.2 Focal-plane shutters . 8
6 Test methods . 9
6.1 General .
...

INTERNATIONAL ISO
STANDARD 516
Fourth edition
2019-04
Camera shutters — Timing — General
definition and mechanical shutter
measurements
Obturateurs d'appareils photographiques — Durée d'exposition —
Définition générale et mesurages d'obturateur mécanique
Reference number
ISO 516:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 516:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 516:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 4
5 Required characteristics and their tolerances . 5
5.1 Exposure time . 5
5.1.1 Exposure time marking . 6
5.1.2 Tolerances . 6
5.2 Delay time . 6
5.2.1 Front shutters . 6
5.2.2 Focal-plane shutters . 8
6 Test methods . 9
6.1 General . 9
6.2 Apparatus . 9
6.2.1 Apparatus . 9
6.2.2 Detector . 9
6.2.3 Time-interval meter .
...

INTERNATIONAL ISO
STANDARD 516
Fourth edition
2019-04
Camera shutters — Timing — General
definition and mechanical shutter
measurements
Obturateurs d'appareils photographiques — Durée d'exposition —
Définition générale et mesurages d'obturateur mécanique
Reference number
ISO 516:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 516:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 516:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 4
5 Required characteristics and their tolerances . 5
5.1 Exposure time . 5
5.1.1 Exposure time marking . 6
5.1.2 Tolerances . 6
5.2 Delay time . 6
5.2.1 Front shutters . 6
5.2.2 Focal-plane shutters . 8
6 Test methods . 9
6.1 General . 9
6.2 Apparatus . 9
6.2.1 Apparatus . 9
6.2.2 Detector . 9
6.2.3 Time-interval meter .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.