ISO 29472:2008/Amd 1:2014
(Amendment)Thermal insulating products for building applications — Determination of dimensional stability under specified temperature and humidity conditions — Amendment 1
Thermal insulating products for building applications — Determination of dimensional stability under specified temperature and humidity conditions — Amendment 1
Produits isolants thermiques destinés aux applications du bâtiment — Détermination de la stabilité dimensionnelle dans des conditions de température et d'humidité spécifiées — Amendement 1
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 29472
First edition
2008-11-01
AMENDMENT 1
2014-12-01
Thermal insulating products
for building applications —
Determination of dimensional
stability under specified temperature
and humidity conditions
AMENDMENT 1
Produits isolants thermiques destinés aux applications du bâtiment —
Détermination de la stabilité dimensionnelle dans des conditions de
température et d’humidité spécifiées
AMENDEMENT 1
Reference number
ISO 29472:2008/Amd.1:2014(E)
©
ISO 2014
---------------------- Page: 1 ----------------------
ISO 29472:2008/Amd.1:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 29472:2008/Amd.1:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 163, Thermal performance and energy use in the
built environment, Subcommittee SC 1, Test and measurement methods.
© ISO 2014 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 29472:2008/Amd.1:2014(E)
iv © ISO 2014 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 29472:2008/Amd.1:2014(E)
Thermal insulating products for building applications —
Determination of dimensional stability under specified
temperature and humidity conditions
AMENDMENT 1
Page V, Introduction
Replace the existing Introduction with the following:
This International Standard comprises the original EN 1604:1996 and EN 1604:1996/AC:1997 prepared
by Technical Committee CEN/TC 88, Thermal insulating materials and products, which have been amended
by ISO/TC 163/SC 1 with reference to conditioning and testing conditions in tropical countries.
This International Standard is one of a series of documents specifying test methods, based on existing
European Standards, that are being adopted by ISO. This “package” of standards includes the following
group of interrelated documents.
Respective
ISO standard Title
EN standard
ISO 12344 Thermal insulating products for building applications — Determination EN 12089
of bending behaviour
ISO 12968 Thermal insulation products for building applications — Determination EN 13495
of the pull-off resistance of external thermal insulation composite sys-
tems (ETICS) (foam block test)
ISO 29465 Thermal insulating products for building applications — Determination EN 822
of length and width
ISO 29466 Thermal insulating products for building applications — Determination EN 823
of thickness
ISO 29467 Thermal insulating products for building applications — Determination EN 824
of squareness
ISO 29468 Thermal insulating products for building applications — Determination EN 825
of flatness
ISO 29469 Thermal insulating products for building applications — Determination EN 826
of compression behaviour
ISO 29470 Thermal insulating products for building applications — Determination EN 1602
of the apparent density
ISO 29471 Thermal insulating products for building applications — Determination EN 1603
of dimensional stability under constant normal laboratory conditions
(23 degree
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.