Liming materials — Determination of size distribution by dry and wet sieving

This document specifies two methods for the determination of the particle size distribution of liming materials. Method A (the dry sieving method) is applicable to all liming materials except wet and paste-like products. Method A is not applicable if blinding, caking, electrostatic charges or agglomeration occur after drying. Method B (the wet sieving method) is applicable to products which are susceptible to blinding, caking, electrostatic charges or agglomeration after drying. Method B can be used to determine the primary particle size distribution of granulated products. Method B is not applicable to burnt lime and liming materials containing water-soluble constituents.

Amendements minéraux basiques — Détermination de la distribution granulométrique par tamisage à sec ou à l'état humide

Ce document spécifie deux méthodes permettant de déterminer la distribution granulométrique des amendements minéraux basiques. La méthode A (méthode de tamisage par voie sèche) est applicable à tous les amendements minéraux basiques, à l'exception des produits humides et pâteux. La méthode A n'est pas applicable si un colmatage, un mottage, des charges électrostatiques ou une agglomération se produisent après séchage. La méthode B (méthode de tamisage par voie humide) est applicable aux produits qui sont susceptibles de colmater le tamis, de s'agglutiner, de provoquer des charges électrostatiques ou de s'agglomérer après séchage. La méthode B peut être utilisée pour déterminer la distribution granulométrique initiale de produits granulés. La méthode B n'est pas applicable à la chaux ni aux amendements minéraux basiques contenant des constituants solubles dans l'eau.

General Information

Status
Published
Publication Date
06-Dec-2018
Current Stage
6060 - International Standard published
Due Date
12-Nov-2018
Completion Date
07-Dec-2018
Ref Project

Buy Standard

Standard
ISO 20977:2018 - Liming materials -- Determination of size distribution by dry and wet sieving
English language
14 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 20977:2018 - Amendements minéraux basiques -- Détermination de la distribution granulométrique par tamisage a sec ou a l'état humide
French language
14 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 20977
First edition
2018-12
Liming materials — Determination of
size distribution by dry and wet sieving
Amendements minéraux basiques — Détermination de la distribution
granulométrique par tamisage à sec ou à l'état humide
Reference number
ISO 20977:2018(E)
ISO 2018
---------------------- Page: 1 ----------------------
ISO 20977:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 20977:2018(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 1

4.1 Suitable methods ................................................................................................................................................................................... 1

4.2 Method A (dry sieving) .................................................................................................................................................................... 4

4.3 Method B (wet sieving) .................................................................................................................................................................... 4

5 Apparatus ..................................................................................................................................................................................................................... 4

6 Sampling ........................................................................................................................................................................................................................ 4

7 Procedure..................................................................................................................................................................................................................... 5

7.1 Test portion ................................................................................................................................................................................................ 5

7.2 Method A (dry sieving) .................................................................................................................................................................... 5

7.2.1 Preparation of test portions ................................................................................................................................... 5

7.2.2 Determination .................................................................................................................................................................... 5

7.3 Method B (wet sieving) .................................................................................................................................................................... 5

7.3.1 General...................................................................................................................................................................................... 5

7.3.2 Determination .................................................................................................................................................................... 6

8 Expression of results ........................................................................................................................................................................................ 6

8.1 Method A ...................................................................................................................................................................................................... 6

8.2 Method B ...................................................................................................................................................................................................... 7

9 Precision ....................................................................................................................................................................................................................... 7

9.1 General ........................................................................................................................................................................................................... 7

9.2 Repeatability ............................................................................................................................................................................................. 7

9.3 Reproducibility ....................................................................................................................................................................................... 8

10 Test report ................................................................................................................................................................................................................... 8

Annex A (informative) Results of an interlaboratory trial to determine the size distribution

by dry and wet sieving .................................................................................................................................................................................... 9

Bibliography .............................................................................................................................................................................................................................14

© ISO 2018 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 20977:2018(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso

.org/iso/foreword .html.

This document was prepared by Technical Committee ISO/TC 134, Fertilizers, soil conditioners and

beneficial substances.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 20977:2018(E)
Introduction

The dry sieving of powdered material containing individual particles can be carried out quite easily.

This simple, quick and cheap method enables the determination of the particle size of water-soluble

materials. Therefore, the dry sieving method should always be used first. However, the sieve apertures

can become blocked by sample particles, a phenomenon known as blinding. Blinding is mainly caused

by caking and the production of electrostatic charges, particularly on sieves with small apertures. Dry

sieving of very wet material can also lead to blinding. These difficulties are not encountered with the

wet sieving method, which is applicable to any kind of material such as powders (dry or wet), paste-like

products or granules except those containing water-soluble constituents.

In order to ensure the comparability of results, all masses of size fractions are expressed as dry matter.

This document is based on EN 12948:2002.
© ISO 2018 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 20977:2018(E)
Liming materials — Determination of size distribution by
dry and wet sieving
1 Scope

This document specifies two methods for the determination of the particle size distribution of liming

materials.

Method A (the dry sieving method) is applicable to all liming materials except wet and paste-like

products. Method A is not applicable if blinding, caking, electrostatic charges or agglomeration occur

after drying.

Method B (the wet sieving method) is applicable to products which are susceptible to blinding, caking,

electrostatic charges or agglomeration after drying. Method B can be used to determine the primary

particle size distribution of granulated products. Method B is not applicable to burnt lime and liming

materials containing water-soluble constituents.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 565, Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes

of openings

ISO 3310-1, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth

ISO 8397:1988, Solid fertilizers and soil conditioners — Test sieving

ISO 14820-1, Fertilizers and liming materials — Sampling and sample preparation — Part 1: Sampling

EN 12048, Solid fertilisers and liming materials — Determination of moisture content — Gravimetric

method by drying at (105 ± 2) °C
3 Terms and definitions
No terms and definitions are listed in this document.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
4 Principle
4.1 Suitable methods
Table 1 gives the recommended methods for different liming materials.
In case of different options, see remarks.
© ISO 2018 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO 20977:2018(E)
2 © ISO 2018 – All rights reserved
Table 1 — Suitable methods for size distribution determination
Material Water
Presentation Moisture Size range on the market Suitable method(s) Remarks
type soluble
Powder/
Laser diffraction
Defined/
Dry sieving Wet sieving
Yes/No/
Granulated/ Dry/Wet
(not standard-
Partially
(method A) (method B)
Suspension/
ized)
Screened
Powder Dry No 0/10 µm to 0/63 µm — — x
Powder Dry No 0/63 µm to 0/100 µm x — x
Powder Dry No 0/100 µm to 0/5 mm x optional —
after drying for dry sieving
Powder Wet No 0/100 µm to 0/5 mm optional x —
as received for wet sieving
Limestone/
dolomite
Defined Dry No 100 µm/x to y/5 mm x optional —
Granulated Dry No 2/7 mm x — — before breakdown
1 and 2: after breakdown
0/63 µm to 0/1 mm (el-
Granulated Dry No x optional 1 optional 2
ementary particles)
2: up to 200 µm
Suspension Wet No 0/10 µm to 0/250 µm optional — x fraction coarser than 100 µm
Powder Wet No 0/5 mm to 0/ 50 mm — x — as received
Chalk (soft
material)
Powder Dry No 0/63 µm to 0/1 mm x optional —
Powder Dry Partially 0/1 mm to 0/3 mm x — —
Burnt lime
Screened Dry Partially 1/x mm to y/8 mm x — —
Powder Dry Partially 0/50 µm to 0/200 µm x — optional in alcohol
Hydrated
lime
Suspension Wet Partially — — — — no need
BOF slags Powder Dry Partially up to 1 mm x — optional in alcohol
(blast oxy-
Powder Wet Partially up to 4 mm x — — after drying
gen furnace)
Key
x: preferred method
optional: may be used
—: not applicable
---------------------- Page: 7 ----------------------
ISO 20977:2018(E)
© ISO 2018 – All rights reserved 3
Table 1 (continued)
Material Water
Presentation Moisture Size range on the market Suitable method(s) Remarks
type soluble
Powder/
Laser diffraction
Defined/
Dry sieving Wet sieving
Yes/No/
Granulated/ Dry/Wet
(not standard-
Partially
(method A) (method B)
Suspension/
ized)
Screened
Powder Dry No very fine particles x — x
Sugar
Powder Wet No very fine particles x — x after drying
factory lime
Suspension Wet No very fine particles — — x
Powder Dry Partially up to 5 mm x — —
up to 5 mm after prelimi-
Ashes Powder Wet Partially x — — after drying
nary sieving
Granulated Dry Partially 2/7 mm x — —
Key
x: preferred method
optional: may be used
—: not applicable
---------------------- Page: 8 ----------------------
ISO 20977:2018(E)

In some countries, very fine materials (finer than 50 µm) can be found (such as calcium carbonate

suspensions).
For such products, measurement by sieving is not suitable:

Fine particles block the sieve holes and the results cannot be considered as representative.

In this situation, only the laser granulometry measurement is suitable.

However, this measurement is not standardized because the results (xx percent passing yy mm) depend

on a material matrix and on a device calculation algorithm which is specific to each device provider.

Usually, for la
...

NORME ISO
INTERNATIONALE 20977
Première édition
2018-12
Amendements minéraux basiques —
Détermination de la distribution
granulométrique par tamisage à sec
ou à l'état humide
Liming materials — Determination of size distribution by dry and
wet sieving
Numéro de référence
ISO 20977:2018(F)
ISO 2018
---------------------- Page: 1 ----------------------
ISO 20977:2018(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2018

Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette

publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,

y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut

être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.

ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2018 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 20977:2018(F)
Sommaire Page

Avant-propos ..............................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Domaine d’application ................................................................................................................................................................................... 1

2 Références normatives ................................................................................................................................................................................... 1

3 Termes et définitions ....................................................................................................................................................................................... 1

4 Principe .......................................................................................................................................................................................................................... 2

4.1 Méthodes adaptées .............................................................................................................................................................................. 2

4.2 Méthode A (tamisage par voie sèche) ................................................................................................................................. 5

4.3 Méthode B (tamisage par voie humide) ............................................................................................................................ 5

5 Appareillage .............................................................................................................................................................................................................. 5

6 Échantillonnage ..................................................................................................................................................................................................... 5

7 Mode opératoire.................................................................................................................................................................................................... 6

7.1 Prise d’essai ............................................................................................................................................................................................... 6

7.2 Méthode A (tamisage par voie sèche) ................................................................................................................................. 6

7.2.1 Préparation des prises d’essai ............................................................................................................................. 6

7.2.2 Détermination .................................................................................................................................................................... 6

7.3 Méthode B (tamisage par voie humide) ............................................................................................................................ 6

7.3.1 Généralités ............................................................................................................................................................................ 6

7.3.2 Détermination .................................................................................................................................................................... 7

8 Expression des résultats............................................................................................................................................................................... 7

8.1 Méthode A ................................................................................................................................................................................................... 7

8.2 Méthode B ................................................................................................................................................................................................... 8

9 Fidélité ............................................................................................................................................................................................................................ 8

9.1 Généralités .................................................................................................................................................................................................. 8

9.2 Répétabilité ................................................................................................................................................................................................ 8

9.3 Reproductibilité ..................................................................................................................................................................................... 9

10 Rapport d’essai ....................................................................................................................................................................................................... 9

Annexe A (informative) Résultats d’un essai interlaboratoires pour déterminer

la distribution granulométrique par tamisage par voie sèche et par voie humide .....................10

Bibliographie ...........................................................................................................................................................................................................................14

© ISO 2018 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 20977:2018(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes

nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est

en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.

L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui

concerne la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents

critères d'approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www

.iso .org/directives).

L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant

les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de

l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de

brevets reçues par l'ISO (voir www .iso .org/brevets).

Les appellations commerciales éventuellement mentionnées dans le présent document sont données

pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un

engagement.

Pour une explication de la nature volontaire des normes, la signification des termes et expressions

spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion

de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles

techniques au commerce (OTC), voir www .iso .org/avant -propos.

Le présent document a été élaboré par le comité technique ISO/TC 134, Engrais, amendements et

substances bénéfiques.

Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent

document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes

se trouve à l’adresse www .iso .org/fr/members .html.
iv © ISO 2018 – Tous droits réservés
---------------------- Page: 4 ----------------------
ISO 20977:2018(F)
Introduction

Le tamisage par voie sèche d’un matériau pulvérulent contenant des particules individuelles peut être

effectué relativement facilement. Cette méthode, simple, rapide et peu onéreuse, permet de déterminer

la taille des particules de matériaux solubles dans l’eau. Par conséquent, il convient de toujours utiliser

cette méthode de tamisage par voie sèche en premier. Cependant, un phénomène caractéristique peut se

produire, le colmatage, c’est-à-dire le bouchage des orifices du tamis par les particules de l’échantillon.

Le colmatage est principalement causé par le mottage et par la production de charges électrostatiques,

en particulier sur des tamis présentant une petite ouverture de maille. Le tamisage par voie sèche

d’un matériau très humide peut également engendrer des problèmes de colmatage. Ces difficultés ne

se rencontrent pas avec la méthode de tamisage par voie humide, qui est applicable à toute espèce de

matériaux, tels que les poudres (sèches ou humides), les produits pâteux ou les granulés à l’exception de

ceux contenant des constituants solubles dans l’eau.

Pour garantir la comparabilité des résultats, toutes les masses de fractions granulométriques sont

exprimées en matière sèche.
Ce document est basé sur l'EN 12948:2002.
© ISO 2018 – Tous droits réservés v
---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 20977:2018(F)
Amendements minéraux basiques — Détermination de
la distribution granulométrique par tamisage à sec ou à
l'état humide
1 Domaine d’application

Ce document spécifie deux méthodes permettant de déterminer la distribution granulométrique des

amendements minéraux basiques.

La méthode A (méthode de tamisage par voie sèche) est applicable à tous les amendements minéraux

basiques, à l’exception des produits humides et pâteux. La méthode A n’est pas applicable si un

colmatage, un mottage, des charges électrostatiques ou une agglomération se produisent après séchage.

La méthode B (méthode de tamisage par voie humide) est applicable aux produits qui sont susceptibles

de colmater le tamis, de s’agglutiner, de provoquer des charges électrostatiques ou de s’agglomérer

après séchage. La méthode B peut être utilisée pour déterminer la distribution granulométrique initiale

de produits granulés. La méthode B n’est pas applicable à la chaux ni aux amendements minéraux

basiques contenant des constituants solubles dans l’eau.
2 Références normatives

Les documents suivants cités dans le texte constituent, pour tout ou partie de leur contenu, des

exigences du présent document. Pour les références datées, seule l’édition citée s’applique. Pour les

références non datées, la dernière édition du document de référence s’applique (y compris les éventuels

amendements).

ISO 565, Tamis de contrôle — Tissus métalliques, tôles métalliques perforées et feuilles électroformées —

Dimensions nominales des ouvertures

ISO 3310-1, Tamis de contrôle — Exigences techniques et vérifications — Partie 1: Tamis de contrôle en

tissus métalliques
ISO 8397:1988, Matières fertilisantes solides — Tamisage de contrôle

ISO 14820-1, Engrais et amendements minéraux basiques — Échantillonnage et préparation de

l'échantillon — Partie 1: Échantillonnage

EN 12048, Engrais solides et amendements calciques et/ou magnésiens — Détermination de la teneur en

eau — Méthode gravimétrique par séchage à (105 ± 2) °C
3 Termes et définitions
Aucun terme n’est défini dans le présent document.
© ISO 2018 – Tous droits réservés 1
---------------------- Page: 6 ----------------------
ISO 20977:2018(F)

L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en

normalisation, consultables aux adresses suivantes:

— ISO Online Browsing Platform: disponible à l’adresse https: //www .iso .org/obp

— IEC Electropedia: disponible à l’adresse http: //www .electropedia .org/
4 Principe
4.1 Méthodes adaptées

Le Tableau 1 indique les méthodes recommandées pour différents amendements minéraux basiques.

Si plusieurs options sont possibles, voir les remarques.
2 © ISO 2018 – Tous droits réservés
---------------------- Page: 7 ----------------------
ISO 20977:2018(F)
© ISO 2018 – Tous droits réservés 3

Tableau 1 — Méthodes adaptées pour la détermination de la distribution granulométrique

Type de Soluble dans Granulométrie dispo-
Présentation Humidité Méthode(s) adaptée(s) Remarques
matériau l’eau nible sur le marché
Poudre/
Definé/ Oui/ Tamisage par Tamisage par Diffraction
Sec/
Granulé/ Non/ voie sèche voie humide laser
Humide
Suspension/ Partiellement (méthode A) (méthode B) (non normalisée)
Calibrée
Poudre Sec Non 0/10 µm à 0/63 µm — — x
Poudre Sec Non 0/63 µm à 0/100 µm x — x
Poudre Sec Non 0/100 µm à 0/5 mm x facultatif —
après séchage pour le
tamisage par voie sèche
Poudre Humide Non 0/100 µm à 0/5 mm facultatif x —
tel que reçu pour le
Calcaire/
tamisage par voie humide
dolomie
Définé Sec Non 100 µm/x à y/5 mm x facultatif —
Granulés Sec Non 2/7 mm x — — avant délitage
1 et 2: après délitage
0/63 µm à 0/1 mm (par-
Granulés Sec Non x facultatif 1 facultatif 2
ticules élémentaires)
2: jusqu’à 200 µm
fraction plus grossière que
Suspension Humide Non 0/10 µm à 0/250 µm facultatif — x
100 µm
Craie Poudre Humide Non 0/5 mm à 0/50 mm — x — tel que reçu
(matériau
Poudre Sec Non 0/63 µm à 0/1 mm x facultatif —
tendre)
Poudre Sec Partiellement 0/1 mm à 0/3 mm x — —
Chaux vive
Calibrée Sec Partiellement 1/x mm à y/8 mm x — —
Poudre Sec Partiellement 0/50 µm à 0/200 µm x — facultatif dans l’alcool
Chaux
éteinte
Suspension Humide Partiellement — — — — inutile
Légende
x: méthode recommandée
facultatif: peut être utilisé
—: non applicable
---------------------- Page: 8 ----------------------
ISO 20977:2018(F)
4 © ISO 2018 – Tous droits réservés
Tableau 1 (suite)
Type de Soluble dans Granulométrie dispo-
Présentation Humidité Méthode(s) adaptée(s) Remarques
matériau l’eau nible sur le marché
Scories Poudre Sec Partiellement jusqu’à 1 mm x — facultatif dans l’alcool
de hauts-
Poudre Humide Partiellement jusqu’à 4 mm x — — après séchage
fourneaux
Poudre Sec Non très fines particules x — x
Écumes de
Poudre Humide Non très fines particules x — x après séchage
sucrerie
Suspension Humide Non très fines particules — — x
Poudre Sec Partiellement jusqu’à 5 mm x — —
jusqu’à 5 mm après un
Cendres Poudre Humide Partiellement x — — après séchage
tamisage préliminaire
Granulés Sec Partiellement 2/7 mm x — —
Légende
x: méthode recommandée
facultatif: peut être utilisé
—: non applicable
---------------------- Page: 9 ----------------------
ISO 20977:2018(F)

Dans certains pays, des matériaux très fins (moins de 50 µm) sont disponibles (notamment des

suspensions de carbonate de calcium).
Pour ces produits, le mesurage par tamisage n’est pas adapté:

Les fines particules colmatent les orifices du tamis et les résultats ne peuvent pas être considérés

comme représentatifs.
Dans cette situation, seul le mesurage par granulométrie laser est approprié.

Cependant, ce mesurage n’est pas normalisé car les résultats (xx pourcents de passant à yy mm)

dépendent de la matrice du matériau et de l’algorithme de calcul du dispositif qui est spécifique

de chaque fournisseur de dispositif. Généralement, pour la granulométrie laser, les particules sont

dispersées dans l’eau. Lorsque le produit est totalement ou partiellement soluble dans l’eau, il convient

d’utiliser de l’alcool, mais dans ce cas (p
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.