ISO/IEC 15426-2:2015

Information technology — Automatic identification and data capture techniques — Bar code verifier conformance specification — Part 2: Two-dimensional symbols

ISO/IEC 15426-2:2015 defines test methods and minimum accuracy criteria applicable to verifiers using the methodologies of ISO/IEC 15415 for multi-row bar code symbols and two-dimensional matrix symbologies, and specifies reference calibration standards against which these should be tested. It provides for testing of representative samples of the equipment. NOTE ISO/IEC 15426‑1 applies to verifiers for linear bar code symbols.

Technologies de l'information — Techniques automatiques d'identification et de capture des données — Spécifications de conformité des vérificateurs de codes à barres — Partie 2: Symboles bidimensionnels

General Information

• Status: Withdrawn
• Publication Date: 09-Aug-2015
• ICS: 35.040 - Information coding
• ICS: 35.040.50 - Automatic identification and data capture techniques
• Technical Committee: ISO/IEC JTC 1/SC 31 - Automatic identification and data capture techniques
• Drafting Committee: ISO/IEC JTC 1/SC 31/WG 1 - Data carrier
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 13-Dec-2023

Relations

• Consolidates: ISO 3500:2005 - Gas cylinders — Seamless steel CO2 cylinders for fixed fire-fighting installations on ships
• Effective Date: 06-Jun-2022
• Revised: ISO/IEC 15426-2:2023 - Information technology — Automatic identification and data capture techniques — Bar code verifier conformance specification — Part 2: Two-dimensional symbols
• Effective Date: 06-Jun-2022
• Revises: ISO/IEC 15426-2:2005 - Information technology — Automatic identification and data capture techniques — Bar code verifier conformance specification — Part 2: Two-dimensional symbols
• Effective Date: 17-Jul-2010

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 15426-2
Second edition
2015-08-01
Information technology — Automatic
identification and data capture
techniques — Bar code verifier
conformance specification —
Part 2:
Two-dimensional symbols
Technologies de l’information — Techniques automatiques
d’identification et de capture des données — Spécifications de
conformité des vérificateurs de codes à barres —
Partie 2: Symboles bidimensionnels
Reference number
ISO/IEC 15426-2:2015(E)
©
ISO/IEC 2015

---------------------- Page: 1 ----------------------
ISO/IEC 15426-2:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO/IEC 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 15426-2:2015(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Conformance . 1
3 Normative references . 1
4 Terms and definitions . 2
5 Symbols . 2
6 Functional requirements . 2
6.1 General requirements . 2
6.2 Reflectance calibration . 2
6.3 Mandatory functions . 3
6.3.1 Verifiers for multi-row bar code symbols . 3
6.3.2 Verifiers for two-dimensional matrix symbols . 3
6.4 Optional functions . 3
7 General constructional and operational requirements . 4
7.1 Installation, operation and maintenance . 4
7.2 Power supply . 4
7.3 Temperature . 4
7.3.1 Operating temperature range .
...