Fasteners — Hexalobular socket countersunk flat head screws

ISO 14581:2013 specifies the characteristics of hexalobular socket countersunk flat head screws in product grade A and with threads from M2 to M10 inclusive and with reduced loadability (according to Table 3).

Éléments de fixation — Vis à tête fraisée réduite à six lobes internes

L'ISO 14581:2013 spécifie les caractéristiques des vis à tête fraisée réduite à six lobes internes, de grade A, de diamètre de filetage M2 à M10 inclus, et à capacité de charge réduite conformément au Tableau 3.

General Information

Status
Withdrawn
Publication Date
11-Sep-2013
Current Stage
9599 - Withdrawal of International Standard
Completion Date
16-Dec-2022
Ref Project

Relations

Buy Standard

Standard
ISO 14581:2013 - Fasteners -- Hexalobular socket countersunk flat head screws
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 14581:2013 - Éléments de fixation -- Vis a tete fraisée réduite a six lobes internes
French language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 14581
First edition
2013-09-15
Fasteners — Hexalobular socket
countersunk flat head screws
Éléments de fixation — Vis à tête fraisée réduite à six lobes internes
Reference number
ISO 14581:2013(E)
ISO 2013
---------------------- Page: 1 ----------------------
ISO 14581:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 14581:2013(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Dimensions ................................................................................................................................................................................................................. 2

4 Requirements and reference International Standards ................................................................................................ 5

5 Marking .......................................................................................................................................................................................................................... 6

6 Designation ................................................................................................................................................................................................................ 6

Bibliography ................................................................................................................................................................................................................................ 7

© ISO 2013 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 14581:2013(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received. www.iso.org/patents

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

The committee responsible for this document is ISO/TC 2, Fasteners, Subcommittee SC 11, Fasteners

with metric external thread.
iv © ISO 2013 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 14581:2013(E)
Fasteners — Hexalobular socket countersunk flat head
screws
1 Scope

This International Standard specifies the characteristics of hexalobular socket countersunk flat head

screws in product grade A and with threads from M2 to M10 inclusive and with reduced loadability

according to Table 3.

If, in special cases, specifications other than those listed in this International Standard are required,

they can be selected from existing International Standards, e.g. ISO 261, ISO 888, ISO 898-1, ISO 965-2,

ISO 3506-1 and ISO 4759-1.

NOTE Countersunk head screws, high head, made of steel, with property classes 4.8, 8.8 and 10.9, are

specified in ISO 14582, but these products are not interchangeable, because of different head heights.

2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are

indispensable for its application. For dated references, only the edition cited applies. For undated

references, the latest edition of the referenced document (including any amendments) applies.

ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions

ISO 261, ISO general purpose metric screw threads — General plan

ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws

and studs with specified property classes — Coarse thread and fine pitch thread

ISO 965-2, ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general

purpose external and internal screw threads — Medium quality
ISO 3269, Fasteners — Acceptance inspection

ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts,

screws and studs
ISO 4042, Fasteners — Electroplated coatings

ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C

ISO 6157-1, Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements

ISO 7721, Countersunk head screws — Head configuration and gauging
ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts
ISO 10664, Hexalobular internal driving feature for bolts and screws
ISO 10683, Fasteners — Non-electrolytically applied zinc flake coatings
ISO 10684, Fasteners — Hot dip galvanized coatings
ISO 16048, Passivation of corrosion-resistant stainless-steel fasteners
© ISO 2013 – All rights reserved 1
---------------------- Page: 5 ----------------------
ISO 14581:2013(E)
3 Dimensions

See Figure 1 and Table 1. Symbols and descriptions of dimensions are specified in ISO 225.

a) Screws without shoulder for sizes M2 to M4
b) Fully threaded screws with shou
...

NORME ISO
INTERNATIONALE 14581
Première édition
2013-09-15
Éléments de fixation — Vis à tête
fraisée réduite à six lobes internes
Fasteners — Hexalobular socket countersunk flat head screws
Numéro de référence
ISO 14581:2013(F)
ISO 2013
---------------------- Page: 1 ----------------------
ISO 14581:2013(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2013

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée

sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur

l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à

l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2013 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 14581:2013(F)
Sommaire Page

Avant-propos ..............................................................................................................................................................................................................................iv

1 Domaine d’application ................................................................................................................................................................................... 1

2 Références normatives ................................................................................................................................................................................... 1

3 Dimensions ................................................................................................................................................................................................................. 2

4 Exigences et Normes internationales de référence .......................................................................................................... 4

5 Marquage ...................................................................................................................................................................................................................... 6

6 Désignation ................................................................................................................................................................................................................ 6

Bibliographie .............................................................................................................................................................................................................................. 7

© ISO 2013 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 14581:2013(F)
Avant-propos

L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes

nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est

en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.

L’ISO collabore étroitement avec la Commission électrotechnique internationale (CEI) en ce qui concerne

la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/CEI, Partie 1. Il convient, en particulier de prendre note des différents

critères d’approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/CEI, Partie 2, www.iso.

org/directives.

L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de

droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les

références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l’élaboration

du document sont indiqués dans l’Introduction et/ou sur la liste ISO des déclarations de brevets reçues,

www.iso.org/patents.

Les éventuelles appellations commerciales utilisées dans le présent document sont données pour

information à l’intention des utilisateurs et ne constituent pas une approbation ou une recommandation.

Le comité chargé de l’élaboration du présent document est l’ISO/TC 2, Fixations, sous-comité SC 11,

Fixations à filetage métrique extérieur.
iv © ISO 2013 – Tous droits réservés
---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 14581:2013(F)
Éléments de fixation — Vis à tête fraisée réduite à six
lobes internes
1 Domaine d’application

La présente Norme internationale spécifie les caractéristiques des vis à tête fraisée réduite à six

lobes internes, de grade A, de diamètre de filetage M2 à M10 inclus, et à capacité de charge réduite

conformément au Tableau 3.

Si, pour des cas particuliers, des spécifications autres que celles figurant dans la présente Norme

internationale sont requises, elles peuvent être choisies dans les Normes internationales existantes, par

exemple l’ISO 261, l’ISO 888, l’ISO 898-1, l’ISO 965-2, l’ISO 3506-1 et l’ISO 4759-1.

NOTE Les vis à tête fraisée à six lobes internes, tête haute, réalisée en acier, de classe de qualité 4.8, 8.8 et

10.9 sont spécifiées dans l’ISO 14582, mais ces produits ne sont pas interchangeables, en raison de hauteurs de

tête différentes.
2 Références normatives

Les documents suivants, en totalité ou en partie, sont référencés de manière normative dans le présent

document et sont indispensables pour son application. Pour les références datées, seule l’édition citée

s’applique. Pour les références non datées, la dernière édition du document de référence s’applique (y

compris les éventuels amendements).

ISO 225, Éléments de fixation —Vis, goujons et écrous — Symboles et description des dimensions

ISO 261, Filetages métriques ISO pour usages généraux — Vue d’ensemble

ISO 898-1, Caractéristiques mécaniques des éléments de fixation en acier au carbone et en acier allié —

Partie 1: Vis, goujons et tiges filetées de classes de qualité spécifiées — Filetages à pas gros et filetages à pas fin

ISO 965-2, Filetages métriques ISO pour usages généraux — Tolérances — Partie 2: Dimensions limites pour

filetages intérieurs et extérieurs d’usages généraux — Qualité moyenne
ISO 3269, Éléments de fixation — Contrôle de réception

ISO 3506-1, Caractéristiques mécaniques des éléments de fixation en acier inoxydable résistant à la

corrosion — Partie 1: Vis et goujons
ISO 4042, Éléments de fixation — Revêtements électrolytiques

ISO 4759-1, Tolérances des éléments de fixation — Partie 1: Vis, goujons et écrous — Grades A, B et C

ISO 6157-1, Éléments de fixation — Défauts de surface — Partie 1: Vis et goujons d’usage général

ISO 7721, Vis à tête fraisée — Configuration de la tête et vérification par calibre

ISO 8992, Éléments de fixation — Exigences générales pour vis, goujons et écrous
ISO 10664, Empreinte à six lobes internes pour vis

ISO 10683, Éléments de fixation — Revêtements non électrolytiques de lamelles de zinc

ISO 10684, Éléments de fixation — Revêtements de galvanisation à chaud

ISO 16048, Passivation des éléments de fixation en acier inoxydable résistant à la corrosion

© ISO 2013 – Tous droits réservés 1
---------------------- Page: 5 ----------------------
ISO 14581:2013(F)
3 Dimensions

Voir Figure 1 et Tableau 1. Les symboles et descriptions des dimensions sont spécifiés dans l’ISO 225.

a) Vis sans épaulement pour diamètres de filetage M2 à M4
b) Vis entièrement filetées avec épaulement pour diamètres de file
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.