Agricultural tractors — Front-mounted equipment — Part 4: Three-point linkage

This document specifies dimensions and requirements for three-point linkage in association with a power lift for the attachment of implements or equipment to the front of agricultural tractors. It is not applicable to tractors which are designed to run in two directions, where either end can be considered to be the front or the rear. NOTE In this case, ISO 730 applies.

Tracteurs agricoles — Équipement monté à l'avant — Partie 4: Attelage trois points

Le présent document spécifie les dimensions et les exigences applicables aux attelages trois points à relevage assisté, permettant d'atteler des instruments ou des équipements à l'avant des tracteurs agricoles. Il n'est pas applicable aux tracteurs conçus pour se déplacer dans deux directions et dont chacune des deux extrémités peut être indifféremment considérée comme l'extrémité avant ou l'extrémité arrière. NOTE Dans ce cas, l'ISO 730 s'applique.

General Information

Status
Published
Publication Date
14-Nov-2018
Current Stage
9060 - Close of review
Start Date
04-Jun-2029
Ref Project

Relations

Buy Standard

Standard
ISO 8759-4:2018 - Agricultural tractors -- Front-mounted equipment
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 8759-4:2018 - Tracteurs agricoles -- Équipement monté a l'avant
French language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 8759-4
First edition
2018-11
Agricultural tractors — Front-
mounted equipment —
Part 4:
Three-point linkage
Tracteurs agricoles — Équipement monté à l'avant —
Partie 4: Attelage trois points
Reference number
ISO 8759-4:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 8759-4:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 8759-4:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative reference(s) . 1
3 Terms and definitions . 1
4 Dimensions . 1
© ISO 2018 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 8759-4:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture
and forestry, Subcommittee SC 4, Tractors.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
This first edition of ISO 8759-4, together with the third edition of ISO 8759-1 and the first edition of
ISO 8759-3, cancels and replaces ISO 8759-1:1998, which has been technically revised.
A list of all parts in the ISO 8759 series can be found on the ISO website.
iv © ISO 2018 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 8759-4:2018(E)
Agricult
...

NORME ISO
INTERNATIONALE 8759-4
Première édition
2018-11
Tracteurs agricoles — Équipement
monté à l'avant —
Partie 4:
Attelage trois points
Agricultural tractors — Front-mounted equipment —
Part 4: Three-point linkage
Numéro de référence
ISO 8759-4:2018(F)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 8759-4:2018(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2018
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2018 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 8759-4:2018(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et definitions . 1
4 Dimensions . 1
© ISO 2018 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 8759-4:2018(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/directives).
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l'intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir le lien suivant: www .iso .org/iso/foreword .html.
Le présent document a été élaboré par le Comité technique ISO/TC 23, Tracteurs et matériels agricoles et
forestiers, sous-comité SC 4, Tracteurs.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaus
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.