Cycles — Lighting and retro-reflective devices — Part 3: Installation and use of lighting and retro-reflective devices

ISO 6742-3:2015 is applicable to lighting and retro-reflective devices used on cycles intended to be used on public roads and, especially, bicycles complying with ISO 4210 and ISO 8098. ISO 6742-3:2015 specifies the safety requirements and test methods of lighting and retro-reflective devices for fastening devices, control, (guidelines for maintenance), instructions for mounting and use.

Cycles — Éclairages et dispositifs rétroréfléchissant — Partie 3: Installation et usage des éclairages et des dispositifs rétroréfléchissant

General Information

Status
Published
Publication Date
26-May-2015
Current Stage
9092 - International Standard to be revised
Completion Date
10-Feb-2021
Ref Project

Relations

Buy Standard

Standard
ISO 6742-3:2015 - Cycles -- Lighting and retro-reflective devices
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6742-3
First edition
2015-05-15
Cycles — Lighting and retro-
reflective devices —
Part 3:
Installation and use of lighting and
retro-reflective devices
Cycles — Éclairages et dispositifs rétroréfléchissant —
Partie 3: Installation et usage des éclairages et des dispositifs
rétroréfléchissant
Reference number
ISO 6742-3:2015(E)
ISO 2015
---------------------- Page: 1 ----------------------
ISO 6742-3:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 6742-3:2015(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 General ............................................................................................................................................................................................................................ 1

4.1 Tolerances ................................................................................................................................................................................................... 1

4.2 Conditions ................................................................................................................................................................................................... 1

4.3 Order of tests ............................................................................................................................................................................................ 2

5 Requirements .......................................................................................................................................................................................................... 2

5.1 Lighting devices ..................................................................................................................................................................................... 2

5.1.1 Installation requirements ........................................................................................................................................ 2

5.1.2 Fixation requirements ........................................................................................................................................... ...... 2

5.1.3 Control requirements .................................................................................................................................................. 2

5.2 Retro-reflective devices ................................................................................................................................................................... 2

6 Test method ............................................................................................................................................................................................................... 2

6.1 Lighting devices ..................................................................................................................................................................................... 2

6.1.1 Test method for installation ................................................................................................................................... 2

6.1.2 Test method for fixation ............................................................................................................................................ 3

6.2 Retro-reflective devices ................................................................................................................................................................... 5

7 Manufacturer’s instructions ..................................................................................................................................................................... 5

7.1 Lighting devices ..................................................................................................................................................................................... 5

7.1.1 Mounting instructions ........................................................................................................................................... ...... 5

7.1.2 Instructions for use........................................................................................................................................................ 5

7.2 Retro-reflective devices ................................................................................................................................................................... 6

Bibliography ................................................................................................................................................................................................................................ 7

© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 6742-3:2015(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any

patent rights identified during the development of the document will be in the Introduction and/or on

the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity

assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers

to Trade (TBT), see the following URL: Foreword — Supplementary information.

The committee responsible for this document is ISO/TC 149, Cycles, SC 1, Cycles and sub-assemblies.

ISO 6742 consists of the following parts, under the general title Cycles — Lighting and retro-reflective devices:

— Part 1: Lighting and light signalling devices
— Part 2: Retro reflective devices
— Part 3: Installation and use of lighting and retro-reflective devices
— Part 4: Lighting systems powered by the cycle’s movement
— Part 5: Lighting systems not powered by the cycle’s movement
iv © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 6742-3:2015(E)
Introduction

This International Standard has been developed in response to demand throughout the world, and the

aim has been to ensure that bicycles manufactured in compliance with it will be as safe as is practically

possible. The tests have been designed to ensure the strength and durability of individual parts as well

as of the bicycle as a whole, demanding high quality throughout and consideration of safety aspects from

the design stage onwards.

The test method with PSD (6.1.2.2) reflects today’s state of the art and should be preferred to the sine

sweep vibration test (6.1.2.3).
Users of the standard are invited to provide their feedback to ISO/TC 149/SC 1.
© ISO 2015 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 6742-3:2015(E)
Cycles — Lighting and retro-reflective devices —
Part 3:
Installation and use of lighting and retro-reflective devices
1 Scope

This part of ISO 6742 is applicable to lighting and retro-reflective devices used on cycles intended to be

used on public roads and, especially, bicycles complying with ISO 4210 and ISO 8098.

This part of ISO 6742 specifies the safety requirements and test methods of lighting and retro-reflective

devices for fastening devices, control, (guidelines for maintenance), instructions for mounting and use.

2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are

indispensable for its application. For dated references, only the edition cited a

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.