ISO 11515:2013/Amd 1:2018

Gas cylinders — Refillable composite reinforced tubes of water capacity between 450 L and 3000 L — Design, construction and testing — Amendment 1

Bouteilles à gaz — Bouteilles tubulaires en composite renforcé rechargeables d'une capacité de 450 L à 3000 L — Conception, construction et essais — Amendement 1

General Information

• Status: Withdrawn
• Publication Date: 04-Sep-2018
• ICS: 23.020.30 - Pressure vessels, gas cylinders
• Technical Committee: ISO/TC 58/SC 3 - Cylinder design
• Drafting Committee: ISO/TC 58/SC 3/WG 32 - Refillable composite reinforced tubes of water capacity between 150l and 3 000l – Design, construction and testing
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 24-Aug-2022

Relations

• Revised: ISO 11515:2022 - Gas cylinders — Refillable composite reinforced tubes of water capacity between 450 l and 3000 l — Design, construction and testing
• Effective Date: 23-Apr-2020
• Amends: ISO 11515:2013 - Gas cylinders — Refillable composite reinforced tubes of water capacity between 450 L and 3000 L — Design, construction and testing
• Effective Date: 28-Aug-2021

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11515
First edition
2013-07-15
AMENDMENT 1
2018-08
Gas cylinders — Refillable composite
reinforced tubes of water capacity
between 450 L and 3000 L — Design,
construction and testing
AMENDMENT 1
Bouteilles à gaz — Bouteilles tubulaires en composite renforcé
rechargeables d'une capacité de 450 L à 3000 L — Conception,
construction et essais
AMENDEMENT 1
Reference number
ISO 11515:2013/Amd.1:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 11515:2013/Amd.1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11515:2013/Amd.1:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see: www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 3,
Cylinder design.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
© ISO 2018 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 11515:2013/Amd.1:2018(E)
Gas cylinders — Refillable composite reinforced tubes
of water capacity between 450 L and 3000 L — Design,
construction and testing
AMENDMENT 1

8.5.8 Blunt impact test
Replace the text in 8.5.8 with the following:
8.5.8.1 Procedure
For Type 2 tubes, one empty tube, and if necessary, a second empty tube, shall be subjected to two
impacts:
a) one at the tube sidewall midway between the ends;
b) one at the termination of the overwrap near the domes.
For Type 3 and 4 tubes, one empty tube and if necessary a second empty tube, shall be subjected to two
impacts:
a) one at the tube sidewall midway between the ends;
b) one at an angle of 45° to strike the shoulder of the tube (mid arc length at the dome).
See Figure 2.
The impact can be conducted by dropping a suit
...