ISO/DTS 5474-5.2

Electrically propelled road vehicles — Functional requirements and safety requirements for power transfer — Part 5: Automatic conductive power transfer

Véhicules routiers à propulsion électrique - Exigences fonctionnelles et exigences de sécurité pour le transfert de puissance — Partie 5: Transfert de puissance automatique par conduction

General Information

• Status: Not Published
• ICS: 43.120 - Electric road vehicles
• Technical Committee: ISO/TC 22/SC 37 - Electrically propelled vehicles
• Drafting Committee: ISO/TC 22/SC 37 - Electrically propelled vehicles
• Current Stage: 5020 - FDIS ballot initiated: 2 months. Proof sent to secretariat
• Start Date: 29-Sep-2023
• Completion Date: 29-Sep-2023

Standards Content (Sample)

FINAL
TECHNICAL ISO/DTS
DRAFT
SPECIFICATION 5474-5
ISO/TC 22/SC 37
Electrically propelled road vehicles —
Secretariat: DIN
Functional requirements and safety
Voting begins on:
2023-03-06 requirements for power transfer —
Voting terminates on:
Part 5:
2023-05-01
Automated conductive power transfer
Véhicules routiers à propulsion électrique - Exigences fonctionnelles et
exigences de sécurité pour le transfert de puissance —
Partie 5: Transfert d'énergie par conduction automatisé
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/DTS 5474-5:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 1 ----------------------
ISO/DTS 5474-5:2023(E)
FINAL
TECHNICAL ISO/DTS
DRAFT
SPECIFICATION 5474-5
ISO/TC 22/SC 37
Electrically propelled road vehicles —
Secretariat: DIN
Functional requirements and safety
Voting begins on:
requirements for power transfer —
Voting terminates on:
Part 5:
Automated conductive power transfer
Véhicules routiers à propulsion électrique - Exigences fonctionnelles et
exigences de sécurité pour le transfert de puissance —
Partie 5: Transfert d'énergie par conduction automatisé
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: [phone]
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: [e-mail]
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/DTS 5474-5:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 2 ----------------------
ISO/DTS 5474-5:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 System architecture . 5
4.1 General . 5
4.2 Compatibility of EV with ACD offboard subsystem. 6
5 Environmental and operational conditions . 6
6 General safety requirements . 6
6.1 General .
...

ISO/DTS 5474-5:2023(E)
ISO TC 22/SC 37/WG 5
Date: 2023-01-0602
Secretariat: DIN
Electrically propelled road vehicles — Functional requirements and safety requirements for
power transfer — Part 5: Automated conductive power transfer

DTS stage

Warning for WDs and CDs
This document is not an ISO International Standard. It is distributed for review and comment. It is subject to
change without notice and may not be referred to as an International Standard.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
To help you, this guide on writing standards was produced by the ISO/TMB and is available at
A model manuscript of a draft International Standard (known as “The Rice Model”) is available at

---------------------- Page: 1 ----------------------
ISO/DTS 5474-5:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part
of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or
mechanical, including photocopying, or posting on the internet or an intranet, without prior written
permission. Permission can be requested from either ISO at the address below or ISO’s member body
in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.orgwww.iso.org
Published in Switzerland
© ISO 2023 – All rights reserved
ii © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DTS 5474-5:2023(E)
Contents
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 System architecture . 5
4.1 General . 5
4.2 Compatibility of EV with ACD offboard subsystem . 6
5 Environmental and operational conditions . 6
6 General safety requirements . 6
6.1 General . 6
6.2 Disconnection requirements . 6
6.2.1 Manipulator on EVSE side (Case D): . 6
6.2.2 Manipulator on EV side (Case E) . 6
6.3 Protection against mechanically caused injury . 7
7 Functional requirements . 7
7.1 Vehicle localization . 7
7.2 Vehicle coupler localization and positioning . 7
7.3 Manipulator requirements . 7
7.3.1 Manipulator requirements for case D systems . 7
7.3.2 Manipulator requirements for case E systems . 8
7.3.3 Manipulator timing consideration . 8
7.4 Mating space and
...