ISO 10563:2023
(Main)Building and civil engineering sealants — Determination of change in mass and volume
Building and civil engineering sealants — Determination of change in mass and volume
This document specifies a method for the determination of the change of mass and the change of volume of self-levelling and non-sagging sealants used in joints in building construction. NOTE This test procedure is not intended to determine the absolute maximum value of loss of mass and volume of a tested sealant, but it is an indicative measurement of the loss of mass and volume under specified parameters.
Mastics pour bâtiments et ouvrages de génie civil — Détermination des variations de masse et de volume
La présente Norme internationale spécifie une méthode pour la détermination des variations de masse et de volume des mastics auto-nivelant et non coulables utilisés dans des joints dans la construction immobilière. NOTE Cette procédure d’essai n’a pas pour objectif de déterminer la valeur maximale absolue de perte de masse et de volume du mastic testé, mais c'est une mesure indicative de la perte de masse et de volume avec des paramètres spécifiés.
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 10563
Fourth edition
2023-06
Building and civil engineering
sealants — Determination of change
in mass and volume
Mastics pour bâtiments et ouvrages de génie civil — Détermination
des variations de masse et de volume
Reference number
ISO 10563:2023(E)
© ISO 2023
---------------------- Page: 1 ----------------------
ISO 10563:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 10563:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus and materials .1
6 Preparation of test specimens . 2
6.1 For non-sagging sealant . 2
6.2 For self-levelling sealant . 2
7 Test procedure .3
7.1 General . 3
7.2 Preconditioning . 3
7.3 Specific conditioning . 3
8 Calculation and expression of results . 3
8.1 Change in mass . 3
8.2 Change in volume . 4
9 Test report . 4
iii
© ISO 2023 – All rights reserved
---------------------- Page: 3 ----------------------
ISO 10563:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 59, Buildings and civil engineering works,
Subcommittee SC 8, Sealants, in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/SS B02, Structures, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 10563:2017), of which it constitutes a
minor revision. The changes are as follows:
— the title has been revised from Buildings and civil engineering works — Sealants— Determination of
change in mass and volume;
— “mass and” has been added before “volume” twice in the note in the Scope;
— “shall be taken as the test results” has been replaced by “shall be calculated” in 8.1 and 8.2;
— the list items in Clause 9 have been revised.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
© ISO 2023 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 10563:2023(E)
Building and civil engineering sealants — Determination of
change in mass and volume
1 Scope
This document specifies a method for the determination of the change of mass and the change of volume
of self-levelling and non-sagging sealants used in joints in building construction.
NOTE This test procedure is not intended to determine the absolute maximum value of loss of mass and
volume of a tested sealant, but it is an indicative measurement of the loss of mass and volume under specified
parameters.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements
...
NORME ISO
INTERNATIONALE 10563
Quatrième édition
2023-06
Mastics pour bâtiments et ouvrages
de génie civil — Détermination des
variations de masse et de volume
Building and civil engineering sealants — Determination of change in
mass and volume
Numéro de référence
ISO 10563:2023(F)
© ISO 2023
---------------------- Page: 1 ----------------------
ISO 10563:2023(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2023
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
© ISO 2023 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 10563:2023(F)
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives .1
3 Termes et définitions . 1
4 Principe. 1
5 Appareillage et matériaux .1
5.1 Anneaux en métal non corrosif pour le mastic non coulable . 1
5.2 Support anti-adhérent pour le mastic non coulable . 1
5.3 Moules en métal non corrosif pour le mastic auto-nivelant . 2
5.4 Balance . 2
5.5 Liquide d’essai . 2
5.6 Chambre de préconditionnement . 2
5.7 Étuve ventilée . 2
5.8 Récipient . . 2
6 Préparation des éprouvettes . 2
6.1 Pour le mastic non coulable . 2
6.2 Pour le mastic auto-nivelant . 2
7 Mode opératoire d’essai . 3
7.1 Généralités . 3
7.2 Préconditionnement . 3
7.3 Conditionnement spécifique. 3
8 Calcul et expression des résultats .4
8.1 Variation de masse . 4
8.2 Variation de volume . 4
9 Rapport d’essai . 4
iii
© ISO 2023 – Tous droits réservés
---------------------- Page: 3 ----------------------
ISO 10563:2023(F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été préparé par le comité technique ISO/TC 59, Bâtiments et ouvrages de génie
civil, sous-comité SC 8, Mastics, en collaboration avec le comité technique CEN/SS B02, Structures, du
Comité européen de normalisation (CEN), conformément à l'accord de coopération technique entre
l'ISO et le CEN (accord de Vienne).
Cette quatrième édition annule et remplace la troisième édition (ISO 10563:2017), dont elle constitue
une révision mineure. Les modifications sont les suivantes:
— le titre a été révisé de Bâtiments et ouvrages de génie civil - Mastics - Détermination de la variation
de masse et de volume;
— "masse et" a été ajouté avant "volume" deux fois dans la note du champ d'application;
— Les mots "doivent être considérés comme les résultats de l'essai" ont été remplacés par "doivent
être calculés" aux points 8.1 et 8.2;
— les éléments de la liste de l'article 9 ont été révisés.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www.iso.org/fr/members.html.
iv
© ISO 2023 – Tous droits réservés
---------------------- Page: 4 ----------------------
NORME INTERNATION
...
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 10563
ISO/TC 59/SC 8
Building and civil engineering
Secretariat: SAC
sealants — Determination of change
Voting begins on:
2023-03-03 in mass and volume
Voting terminates on:
2023-05-26
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 10563:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 1 ----------------------
ISO/FDIS 10563:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 10563
ISO/TC 59/SC 8
Building and civil engineering
Secretariat: SAC
sealants — Determination of change
Voting begins on:
in mass and volume
Voting terminates on:
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
ISO/CEN PARALLEL PROCESSING
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: +41 22 749 01 11
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: copyright@iso.org
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 10563:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
© ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 2 ----------------------
ISO/FDIS 10563:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus and materials .1
6 Preparation of test specimens . 2
6.1 For nonsagging sealant . 2
6.2 For selflevelling sealant . 2
7 Test procedure .3
7.1 General . 3
7.2 Preconditioning . 3
7.3 Specific conditioning . 3
8 Calculation and expression of results . 3
8.1 Change in mass . 3
8.2 Change in volume . 4
9 Test report . 4
iii
© ISO 2023 – All rights reserved
---------------------- Page: 3 ----------------------
ISO/FDIS 10563:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and nongovernmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 59, Buildings and civil engineering works,
Subcommittee SC 8, Sealants, in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/SS B02, Structures, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 10563:2017), of which it constitutes a
minor revision. The changes are as follows:
— the title has been revised from Buildings and civil engineering works — Sealants— Determination of
change in mass and volume;
— “mass and” has been added before “volume” twice in the note in the Scope;
— “shall be taken as the test results” has been replaced by “shall be calculated” in 8.1 and 8.2;
— the list items in Clause 9 have been revised.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
© ISO 2023 – All rights reserved
---------------------- Page: 4 ----------------------
FINAL
...
ISO/FDIS 10563:20222023(E)
Date: 2023-02-16
ISO TC 59/SC 8
Date: 2022-12-15
Secretariat: SAC
Building and civil engineering sealants — Determination of
change in mass and volume
DIS stage
© ISO 2022 – All rights reserved
---------------------- Page: 1 ----------------------
© ISO 2023 – All rights reserved
© ISO 2022
---------------------- Page: 2 ----------------------
ISO/FDIS 10563:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of
this publication may be reproduced or utilized otherwise in any form or by any means, electronic or
mechanical, including photocopying, or posting on the internet or an intranet, without prior written
permission. Permission can be requested from either ISO at the address below or ISO’s member body in the
country of the requester.
ISO Copyright Office
CP 401 • CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland.
iv © ISO 2023 – All rights reserved
---------------------- Page: 3 ----------------------
ISO/FDIS 10563:2023(E)
Contents
Foreword .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus and materials . 1
6 Preparation of test specimens . 2
6.1 For non-sagging sealant . 2
6.2 For self-levelling sealant . 2
7 Test procedure . 3
7.1 General . 3
7.2 Preconditioning . 3
7.3 Specific conditioning . 3
8 Calculation and expression of results . 4
8.1 Change in mass . 4
8.2 Change in volume . 4
9 Test report . 4
© ISO 2023 – All rights reserved v
---------------------- Page: 4 ----------------------
ISO/FDIS 10563:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 59, BuildingBuildings and civil engineering
works, Subcommittee SC 8, Sealants., in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/SS B02, Structures, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This forthfourth edition cancels and replaces the third edition (ISO 10563:2017), of which has been
minor editoralit constitutes a minor revision. The changes are as follows:
— the title has been revised from Buildings and civil engineering works — Sealants— Determination of
change in mass and volume;
— “mass and” has been added before “volume” twice in the note in the Scope;
— “shall be taken as the test results” has been replaced by “shall be calculated” in 8.1 and 8.2;
— the list items in Clause 9 have been revised.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
vi © ISO 2023 – All rights reserved
---------------------- Page: 5 ----------------------
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 10563:2023(E)
Building and civil engineering sealants —Determination of change
in mass and volume
1 Scope
This document specifies a method for the determination of the change of mass and the change of volume
of self-levelling and non-sagging sealants used in joints in building construction.
NOTE This test procedure is not intended to determine the absolute maximum value of loss of mass and volume
of a tested sealant, but it is an indicative measurement of the loss of mass and volume under specified parameters.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 6927, BuildingsBuilding and civil engineering works — Sealants —sealants — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6927 apply.
ISO and IEC maintain terminology databases for
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.