Hydraulic fluid power — Filter elements — Sequence of tests for verifying performance characteristics

ISO 11170:2003 defines a sequence of tests for verifying filter elements. It can be used to check their hydraulic, mechanical and separation characteristics. ISO 11170:2003 is not intended to qualify a filter for a particular duty or replicate conditions of service. This can only be done by a specific test protocol developed for the purpose, including actual conditions of use (for example the operating fluid). The procedure in ISO 11170:2003 is applicable to individual fluids, or types of fluids having similar chemistry.

Transmissions hydrauliques — Éléments filtrants — Ordre des essais pour la vérification des caractéristiques de performance

L'ISO 11170:2003 définit l'ordre des essais permettant de vérifier les éléments filtrants. Elle peut être utilisée pour contrôler les caractéristiques hydrauliques, mécaniques et séparatives de ces éléments. L'ISO 11170:2003 n'est pas destinée à qualifier un filtre pour une application particulière ou à simuler les conditions de service. Cela ne peut être réalisé que par un mode opératoire d'essai spécifique mise en place à cette fin et qui inclut des conditions réelles d'utilisation (par exemple le fluide de service). Le mode opératoire spécifié dans l'ISO 11170:2003 s'applique à des fluides individuels ou à des types de fluides ayant une composition chimique semblable.

Fluidna tehnika – Hidravlika – Filtrski vložki – Postopki za preverjanje lastnosti

General Information

Status
Withdrawn
Publication Date
20-Aug-2003
Withdrawal Date
20-Aug-2003
Current Stage
9599 - Withdrawal of International Standard
Completion Date
13-Feb-2013

Relations

Buy Standard

Standard
ISO 11170:2003 - Hydraulic fluid power -- Filter elements -- Sequence of tests for verifying performance characteristics
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 11170:2005
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 11170:2003 - Transmissions hydrauliques -- Éléments filtrants -- Ordre des essais pour la vérification des caractéristiques de performance
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11170
Second edition
2003-09-01


Hydraulic fluid power — Filter
elements — Sequence of tests for
verifying performance characteristics
Transmissions hydrauliques — Éléments filtrants — Ordre des essais
pour la vérification des caractéristiques de performance





Reference number
ISO 11170:2003(E)
©
ISO 2003

---------------------- Page: 1 ----------------------
ISO 11170:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

---------------------- Page: 2 ----------------------
ISO 11170:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11170 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 6,
Contamination control.
This second edition cancels and replaces the first edition (ISO 11170:1995), which has been technically
revised.
© ISO 2003 — All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 11170:2003(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within a
closed circuit. The liquid is both a lubricant and power-transmitting medium. The presence of solid
contaminant particles in the liquid interferes with the ability of the hydraulic fluid to lubricate and causes wear
to the components. The extent of contamination in the fluid has a direct bearing in the performance and
reliability of the system, and needs to be controlled to levels that are considered appropriate for the system
concerned. Filters are used to control the contamination level of the fluid by removing solid contaminant
particles.
Different principles are used for this purpose; one of these uses a filter element enclosed in a filter housing.
The filter element is the porous device that performs the actual process of filtration. The complete assembly is
designated as a filter.
The performance of filter elements is measured by testing, and a series of International Standards has been
developed to determine performance under specified conditions (see Clause 2). To give a greater level of
assurance for a filter element's fitness for duty, most if not all of these tests should be used in a verification
programme.
This International Standard provides an approval or verification protocol that features all of the current
International Standards for filter testing.

iv © ISO 2003 — All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 11170:2003(E)

Hydraulic fluid power — Filter elements — Sequence of tests
for verifying performance characteristics
1 Scope
This International Standard defines a sequence of tests for verifying filter elements. It can be used to check
their hydraulic, mechanical and separation characteristics.
This International Standard is not intended to qualify a filter for a particular duty or replicate conditions of
service. This can only be done by a specific test protocol developed for the purpose, including actual
conditions of use (for example the operating fluid).
The procedure in this International Standard is applicable to individual fluids, or types of fluids having similar
chemistry.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 2941, Hydraulic fluid power — Filter elements — Verification of collapse/burst resistance
ISO 2942, Hydraulic fluid power — Filter elements — Verification of fabrication integrity and determination of
the first bubble point
ISO 2943:1998, Hydraulic fluid power — Filter elements — Verification of material compatibility with fluids
ISO 3723, Hydraulic fluid power — Filter elements — Method for end load test
ISO 3724, Hydraulic fluid power — Filter elements — Verification of flow fatigue characteristics
ISO 3968, Hydraulic fluid power — Filters — Evaluation of differential pressure versus flow characteristics
ISO 4406, Hydraulic fluid power — Fluids — Method for coding the level of contamination by solid particles
ISO 5598, Fluid power systems and components — Vocabulary
ISO 16889, Hydraulic fluid power filters — Multi-pass method for evaluating filtration performance of a filter
element
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5598 apply.
© ISO 2003 — All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 11170:2003(E)
4 Test samples
The filter elements selected for verification testing shall be representative of
...

SLOVENSKI STANDARD
SIST ISO 11170:2005
01-november-2005
Fluidna tehnika – Hidravlika – Filtrski vložki – Postopki za preverjanje lastnosti
Hydraulic fluid power -- Filter elements -- Sequence of tests for verifying performance
characteristics
Transmissions hydrauliques -- Éléments filtrants -- Ordre des essais pour la vérification
des caractéristiques de performance
Ta slovenski standard je istoveten z: ISO 11170:2003
ICS:
23.100.60 )LOWULWHVQLODLQ Filters, seals and
RQHVQDåHYDQMHWHNRþLQ contamination of fluids
SIST ISO 11170:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 11170:2005

---------------------- Page: 2 ----------------------

SIST ISO 11170:2005


INTERNATIONAL ISO
STANDARD 11170
Second edition
2003-09-01


Hydraulic fluid power — Filter
elements — Sequence of tests for
verifying performance characteristics
Transmissions hydrauliques — Éléments filtrants — Ordre des essais
pour la vérification des caractéristiques de performance





Reference number
ISO 11170:2003(E)
©
ISO 2003

---------------------- Page: 3 ----------------------

SIST ISO 11170:2005
ISO 11170:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 11170:2005
ISO 11170:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11170 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 6,
Contamination control.
This second edition cancels and replaces the first edition (ISO 11170:1995), which has been technically
revised.
© ISO 2003 — All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 11170:2005
ISO 11170:2003(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within a
closed circuit. The liquid is both a lubricant and power-transmitting medium. The presence of solid
contaminant particles in the liquid interferes with the ability of the hydraulic fluid to lubricate and causes wear
to the components. The extent of contamination in the fluid has a direct bearing in the performance and
reliability of the system, and needs to be controlled to levels that are considered appropriate for the system
concerned. Filters are used to control the contamination level of the fluid by removing solid contaminant
particles.
Different principles are used for this purpose; one of these uses a filter element enclosed in a filter housing.
The filter element is the porous device that performs the actual process of filtration. The complete assembly is
designated as a filter.
The performance of filter elements is measured by testing, and a series of International Standards has been
developed to determine performance under specified conditions (see Clause 2). To give a greater level of
assurance for a filter element's fitness for duty, most if not all of these tests should be used in a verification
programme.
This International Standard provides an approval or verification protocol that features all of the current
International Standards for filter testing.

iv © ISO 2003 — All rights reserved

---------------------- Page: 6 ----------------------

SIST ISO 11170:2005
INTERNATIONAL STANDARD ISO 11170:2003(E)

Hydraulic fluid power — Filter elements — Sequence of tests
for verifying performance characteristics
1 Scope
This International Standard defines a sequence of tests for verifying filter elements. It can be used to check
their hydraulic, mechanical and separation characteristics.
This International Standard is not intended to qualify a filter for a particular duty or replicate conditions of
service. This can only be done by a specific test protocol developed for the purpose, including actual
conditions of use (for example the operating fluid).
The procedure in this International Standard is applicable to individual fluids, or types of fluids having similar
chemistry.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 2941, Hydraulic fluid power — Filter elements — Verification of collapse/burst resistance
ISO 2942, Hydraulic fluid power — Filter elements — Verification of fabrication integrity and determination of
the first bubble point
ISO 2943:1998, Hydraulic fluid power — Filter elements — Verification of material compatibility with fluids
ISO 3723, Hydraulic fluid power — Filter elements — Method for end load test
ISO 3724, Hydraulic fluid power — Filter elements — Verification of flow fatigue characteristics
ISO 3968, Hydraulic fluid power — Filters — Evaluation of differential pressure versus flow characteristics
ISO 4406, Hydraulic fluid power — Fluids — Method for coding the level of contamination by solid particles
ISO 5598, Fluid power syste
...

NORME ISO
INTERNATIONALE 11170
Deuxième édition
2003-09-01



Transmissions hydrauliques — Éléments
filtrants — Ordre des essais pour la
vérification des caractéristiques de
performance
Hydraulic fluid power — Filter elements — Sequence of tests for
verifying performance characteristics





Numéro de référence
ISO 11170:2003(F)
©
ISO 2003

---------------------- Page: 1 ----------------------
ISO 11170:2003(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


©  ISO 2003
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2003 — Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 11170:2003(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 11170 a été élaborée par le comité technique ISO/TC 131, Transmissions hydrauliques et
pneumatiques, sous-comité SC 6, Contrôle de la contamination.
Cette deuxième édition annule et remplace la première édition (ISO 11170:1995), dont elle constitue une
révision technique.
© ISO 2003 — Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 11170:2003(F)
Introduction
Dans les systèmes de transmissions hydrauliques, l'énergie est transmise et commandée par l'intermédiaire
d'un liquide sous pression circulant en circuit fermé. Ce liquide sert à la fois à lubrifier le système et à
transmettre de l'énergie. La présence d'une pollution particulaire solide dans le liquide entrave la capacité du
fluide hydraulique à lubrifier le système et provoque l'usure des composants. Une pollution trop importante
influe directement sur les performances et la fiabilité du système, c'est pourquoi elle doit être maintenue à un
niveau jugé approprié au système concerné. Le niveau de pollution du fluide est contrôlé par des filtres qui
retiennent les particules solides polluantes.
Différents principes sont utilisés pour atteindre cet objectif; l'un de ces principes consiste à utiliser un corps de
filtre équipé d'un élément filtrant. Ce dernier est un dispositif poreux qui réalise le processus réel de filtration.
L'ensemble de cet assemblage est désigné sous le terme de filtre.
Les performances des éléments filtrants sont mesurées par l'intermédiaire d'essais. Une série de Normes
internationales a été élaborée dans le but de déterminer les performances du système dans des conditions
particulières (voir l'Article 2). Pour être certain qu'un élément filtrant correspond à son utilisation, il convient
d'intégrer la plupart, voire la totalité de ces essais au sein d'un programme de vérification.
La présente Norme internationale constitue un protocole d'homologation ou de vérification qui met en œuvre
toutes les Normes internationales existantes en matière d'essais des filtres.

iv © ISO 2003 — Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 11170:2003(F)

Transmissions hydrauliques — Éléments filtrants — Ordre des
essais pour la vérification des caractéristiques de performance
1 Domaine d'application
La présente Norme internationale définit l'ordre des essais permettant de vérifier les éléments filtrants. Elle
peut être utilisée pour contrôler les caractéristiques hydrauliques, mécaniques et séparatives de ces éléments.
La présente Norme internationale n'est pas destinée à qualifier un filtre pour une application particulière ou à
simuler les conditions de service. Cela ne peut être réalisé que par un mode opératoire d'essai spécifique mis
en place à cette fin et qui inclut des conditions réelles d'utilisation (par exemple le fluide de service).
Le mode opératoire spécifié dans la présente Norme internationale s'applique à des fluides individuels ou à
des types de fluides ayant une composition chimique semblable.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 2941, Transmissions hydrauliques — Éléments filtrants — Vérification de la résistance à l'écrasement ou
à l'éclatement
ISO 2942, Transmissions hydrauliques — Éléments filtrants — Vérification de la conformité de fabrication et
détermination du point de première bulle
ISO 2943:1998, Transmissions hydrauliques — Éléments filtrants — Vérification de la compatibilité des
matériaux avec les fluides
ISO 3723, Transmissions hydrauliques — Éléments filtrants — Méthode de détermination de la résistance à la
déformation axiale
ISO 3724, Transmissions hydrauliques — Éléments filtrants — Vérification des caractéristiques d'un filtre par
un essai de fatigue due au débit
ISO 3968, Transmissions hydrauliques — Filtres — Évaluation de la perte de charge en fonction du débit
ISO 4406, Transmissions hydrauliques — Fluides — Méthode de codification du niveau de pollution
particulaire solide
ISO 5598, Transmissions hydrauliques et pneumatiques — Vocabulaire
ISO 16889, Filtres pour transmissions hydrauliques — Évaluation des performances par la méthode de
filtration en circuit fermé
© ISO 2003 — Tous droits réservés 1

---------------------- Page: 5 ----------------------
ISO 11170:2003(F)
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l'ISO 5598 s'appliquent.
4 Échantillons d'essai
Les éléments filtrants sélectionnés pour les essais de vérification doivent être représentati
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.