ISO 23146:2008
(Main)Fine ceramics (advanced ceramics, advanced technical ceramics) — Test methods for fracture toughness of monolithic ceramics — Single-edge V-notch beam (SEVNB) method
Fine ceramics (advanced ceramics, advanced technical ceramics) — Test methods for fracture toughness of monolithic ceramics — Single-edge V-notch beam (SEVNB) method
ISO 23146:2008 specifies a method for the determination of the fracture toughness of advanced technical ceramics. The procedure makes use of single-edge V-notched bars, which are loaded in 4-point bending until failure. It is applicable to monolithic ceramics with a grain size or major microstructural feature size larger than about 1 µm. The use of ISO 23146:2008 for yttria tetragonal zirconia polycrystal material (Y-TZP) is not recommended. The method might also be unsuitable for some other very tough or soft ceramics in which a sharp crack does not form at the root of the V-notch.
Céramiques techniques — Méthodes d'essai pour la détermination de la ténacité à la rupture des céramiques monolithiques — Méthode sur éprouvette à entaille en V sur une seule face (Méthode SEVNB)
General Information
- Status
- Withdrawn
- Publication Date
- 21-May-2008
- Withdrawal Date
- 21-May-2008
- Technical Committee
- ISO/TC 206 - Fine ceramics
- Drafting Committee
- ISO/TC 206 - Fine ceramics
- Current Stage
- 9599 - Withdrawal of International Standard
- Start Date
- 13-Dec-2012
- Completion Date
- 14-Feb-2026
Relations
- Effective Date
- 19-May-2012
Frequently Asked Questions
ISO 23146:2008 is a standard published by the International Organization for Standardization (ISO). Its full title is "Fine ceramics (advanced ceramics, advanced technical ceramics) — Test methods for fracture toughness of monolithic ceramics — Single-edge V-notch beam (SEVNB) method". This standard covers: ISO 23146:2008 specifies a method for the determination of the fracture toughness of advanced technical ceramics. The procedure makes use of single-edge V-notched bars, which are loaded in 4-point bending until failure. It is applicable to monolithic ceramics with a grain size or major microstructural feature size larger than about 1 µm. The use of ISO 23146:2008 for yttria tetragonal zirconia polycrystal material (Y-TZP) is not recommended. The method might also be unsuitable for some other very tough or soft ceramics in which a sharp crack does not form at the root of the V-notch.
ISO 23146:2008 specifies a method for the determination of the fracture toughness of advanced technical ceramics. The procedure makes use of single-edge V-notched bars, which are loaded in 4-point bending until failure. It is applicable to monolithic ceramics with a grain size or major microstructural feature size larger than about 1 µm. The use of ISO 23146:2008 for yttria tetragonal zirconia polycrystal material (Y-TZP) is not recommended. The method might also be unsuitable for some other very tough or soft ceramics in which a sharp crack does not form at the root of the V-notch.
ISO 23146:2008 is classified under the following ICS (International Classification for Standards) categories: 81.060.30 - Advanced ceramics. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 23146:2008 has the following relationships with other standards: It is inter standard links to ISO 23146:2012. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
ISO 23146:2008 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 23146
First edition
2008-06-01
Fine ceramics (advanced ceramics,
advanced technical ceramics) — Test
methods for fracture toughness of
monolithic ceramics — Single-edge V-notch
beam (SEVNB) method
Céramiques techniques — Méthodes d'essai pour la détermination de la
ténacité à la rupture des céramiques monolithiques — Méthode sur
éprouvette à entaille en V sur une seule face (Méthode SEVNB)
Reference number
©
ISO 2008
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
©
ii ISO 2008 – All rights reserved
Contents Page
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Test piece preparation . 3
6.1 Number of test pieces . 3
6.2 Test-piece dimensions . 3
6.3 Preparing the V-notch by hand . 4
6.4 Preparing the V-notches by machine (optional) . 6
6.5 Determination of notch-root radius . 7
7 Test procedure . 8
7.1 Dimensions of test piece . 8
7.2 Flexural-strength test . 8
7.3 Measurement of notch depth . 8
7.4 Calculation of fracture toughness . 9
8 Precision and bias . 10
9 Test report . 11
Annex A (informative) Notch honing by machine . 12
Annex B (informative) Interlaboratory evaluation of the SEVNB fracture
toughness test procedures . 13
Annex C (informative) Corrections for effective crack length greater than notch depth . 15
Bibliography . 16
©
ISO 2008 – All rights reserved iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 23146 was prepared by Technical Committee ISO/TC 206, Fine ceramics.
©
iv ISO 2008 – All rights reserved
INTERNATIONAL STANDARD ISO 23146:2008(E)
Fine ceramics (advanced ceramics, advanced technical
ceramics) — Test methods for fracture toughness of monolithic
ceramics — Single-edge V-notch beam (SEVNB) method
1Scope
This International Standard specifies a method for the determination of the fracture toughness of advanced
technical ceramics. The procedure makes use of single-edge V-notched bars, which are loaded in 4-point
bending until failure. It is applicable to monolithic ceramics with a grain size or major microstructural feature size
larger than about 1µm.
The use of this International Standard for yttria tetragonal zirconia polycrystal material (Y-TZP) is not
recommended. The method might also be unsuitable for some other very tough or soft ceramics in which a
sharp crack does not form at the root of the V-notch.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 3611, Geometrical product specifications (GPS) — Dimensional measuring instruments — Micrometers for
external measurements; Design and metrological characteristics
ISO 7500-1, Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression
testing machines — Verification and calibration of the force-measuring system
ISO 14704, Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for flexural
strength of monolithic ceramics at room temperature
ISO 15732, Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for fracture
toughness of monolithic ceramics at room temperature by single edge precracked beam (SEPB) method
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 15732 apply.
4 Principle
This method of conducting a fracture toughness test is based on the preparation and fracture of bar test pieces
in which a sharp-tipped notch is machined. Using the technique of a reciprocating razor blade and diamond
paste, a narrow notch can be honed into a test piece using either a manual method or a simple machine. Under
well-controlled conditions, a notch-tip radius in the range of 1µm to 20µm can be prepared depending on the
grain size of the test material. For many materials, this is a close approximation to a sharp crack, and the
method has been found to give fracture toughness values very close to those of other methods such as the
single-edge precracked beam method (ISO 15732) or the surface crack in flexure method (ISO 18756) provided
that a sharp crack forms at the root of the notch either during its preparation or during the subsequent fracture
sequence. The method has the advantage of simplicity of notch production compared with using a sharp-tipped
diamond saw or a diamond impregnated wire in which the tip radius is normally greater than 50µm. The method
©
ISO 2008 – All rights reserved 1
is often easier to undertake compared with other methods of precracking, and is applicable to a wider range of
materials outside the scope of these methods.
The method has been extensively researched (see the Bibliography) and has been evaluated in an ESIS
(European Structural Integrity Society)/VAMAS (Versailles Agreement on Advanced Materials and Standards)
round robin, the results of which are summarised in Annex B. This recommended practice is based upon the
ESIS/VAMAS SEVNB round robin.
The method may have some limitations for materials with grain sizes of less than 1µm, for which the
assumption that the notch approximates to a sharp crack may not be valid (see Annex C). Users should strive
to minimize the notch-root radius in the test pieces. This International Standard places a provisional criterion
that the notch-root radius should be similar to or less than twice the average grain size of the material.
The method is complementary to other methods of measuring fracture toughness described in ISO 15732
(single-edge precracked beam method), ISO 18756 (surface crack in flexure method), and ISO 24370 (chevron
notch method); see the Bibliography.
5 Apparatus
5.1 Ordinary razor blades, preferably with a support along one edge but alternatively inserted in a suitable
holder.
NOTE 1 Razor blades thinner than about 0,2 mm are not ideal for this task unless stiffened by a support, such as by gluing
◦
or screwing between two steel plates, leaving only about 2mm of edge showing. A razor blade with a tip angle of 30 or
smaller is ideal.
NOTE 2 Although it is possible to machine the notches entirely by hand, the use of a simple device in which the test pieces
are mounted and in which a razor blade primed with diamond paste is moved in a reciprocating motion across the mounted
test pieces has a distinct advantage, as this provides controlled loading and directional stability to the razor blade, and
sharper notches are produced. An example is shown in Annex A.
5.2 Metallographic diamond paste, in a viscous organic carrier and of fine grain size, typically 1µm to 3µm.
5.3 Lubricant, a light lubricating oil for lubricating the razor blade, e.g. clock oil.
5.4 Test piece support, consisting of a flat plate or other suitable device for mounting test pieces during
notch honing.
5.5 Flexural-strength test fixture, preferably, a four-point flexural-strength test fixture operating in
accordance with the requirements of ISO 14704, i.e. either 1/4-point flexure (preferred) or 1/3-point flexure.
Alternatively, a three-point flexural-strength test jig may also be used, but the alignment of the V-notch with the
central loading roller is more critical.
The test piece is supported on two bearing edges perpendicular to its length. The outer-support bearing edges
shall be parallel rollers of diameter 5,0 mm± 0,2 mm and shall be capable of rolling outward on flat support
surfaces. Preferably, one of the rollers shall additionally be capable of rotating about an axis parallel to the
length of the test piece such that torsional loading is minimised. The two rollers shall be positioned initially with
their centres 40,0 mm± 0,5 mm (1/4-point flexure) or 30 mm± 0,5 mm (1/3-point flexure) apart with their axes
◦
parallel to within 1 . The separation of the centres of the rollers in their starting positions shall be measured to
the nearest 0,1 mm with a travelling microscope. The rollers shall be made from hardened steel or other hard
material with a hardness greater than 40 HRC (Rockwell C-scale). The rollers shall have a smooth burr-free
surface finish with roughness less than 0,5µm Ra, and shall have a diameter uniform to ± 0,02 mm.
For four-point flexure, the two loading rollers are located at the 1/4-points (or 1/3-points), with an inner span of
20 mm± 0,2 mm (or 10 mm± 0,2 mm for 1/3-point flexure) and are free to roll inwards. The rollers are free to
rotate separately about an axis parallel to the length of the test piece to allow alignment. For three-point flexure,
the single loading roller, which need not rotate, shall be positioned centrally between the outer-support rollers.
The distances between the rollers shall be measured to the nearest 0,1 mm along the length of the specimen
perpendicular to the direction of loading, using a travelling microscope or other suitable device. The loading
rollers in four-point flexure shall be symmetrically positioned to within ± 0,1 mm. The arrangement for loading
©
2 ISO 2008 – All rights reserved
shall ensure that equal forces are applied to the two loading rollers. The single loading roller in three-point
flexure shall be centrally located to within ± 0,2 mm.
5.6 Mechanical testing machine, capable of applying a force at a constant rate of displacement or constant
loading rate to the test piece in the flexural-strength test jig and of recording the force at which the test piece
fractures. The force measuring device shall be in accordance with ISO 7500-1 and shall have an accuracy of
� 1%.
NOTE The test facility can, with advantage, be equipped with a capability for recording the force/displacement behaviour of
the test piece, ideally a sensitive system directly contacting the test piece. Provided that the load-train stiffness is sufficient,
machine displacement recording can be adequate.
5.7 Ultrasonic cleaning bath, for cleaning the test pieces after notching, suitable for insertion of a beaker or
other receptacle containing solvent.
5.8 Calibrated micrometer, similar to the one in accordance with ISO 3611, but capable of being read to a
precision of 0,002 mm using a vernier or electronic readout.
5.9 Optical microscope, with calibrated magnifications over the range 50× to 500×, suitable for observing
the notch-tip shape, and fitted with photomicrographic facilities.
5.10 Notch-measuring device, a calibrated device for measuring the depth of the sawn notch after fracture
with a reading precision of 0,002 mm.
NOTE This can be achieved by the use of an appropriate travelling microscope, or a conventional metallurgical microscope
with calibrated stage movement, or a microscope with a calibrated micrometer eyepiece.
◦ ◦
5.11 Drying oven, capable of maintaining 120 C± 5 C for drying test pieces after cleaning.
5.12 Diamond slitting saw or slitting machine, capable of preparing a shallow notch in a set of test pieces
of width no more than 0,5 mm and depth of about 0,5 mm. See 6.3 for guidance.
6 Test piece preparation
6.1 Number of test pieces
At least seven test pieces shall be prepared for notching, of which five are required for testing and two are
dummy test pieces for protecting the others during notch preparation.
NOTE If a machine is used for preparing the V-notches, it might not be necessary to employ the dummy test pieces to
protect a test set of five test pieces.
Operators with no experience of preparing the sharp V-notches used in this method are highly recommended to
try out the technique and equipment first with surplus test pieces.
6.2 Test-piece dimensions
Prepare bar test pieces of rectangular cross-section, preferably in accordance with the requirements of
ISO 14704. Figure 1 shows the shape and main dimensions of the test pieces prepared in accordance with this
International Standard.
NOTE 1 The chamfering or rounding requirements in ISO 14704 are not essential for the V-notch test, and can be ignored.
NOTE 2 Other sizes of test pieces, e.g. (2× 2,5× > 25 mm) can optionally be used with appropriately sized flexural-
strength fixtures.
©
ISO 2008 – All rights reserved 3
Key
L > 45 mm (1/4-point flexure) or > 35 mm (1/3-point flexure)
W 4,0 mm± 0,2 mm
B 3,0 mm± 0,2 mm
Figure 1 — Test piece dimensions in accordance with ISO 14704
6.3 Preparing the V-notch by hand
Mount the test pieces side by side on the test-piece support using an appropriate temporary adhesive, as in
Figure 2. Mount test pieces and dummies as close together as possible. Ensure that the top surfaces of the test
pieces are level. Draw a pencil line across the set of test pieces at the mid-point of their length, to indicate where
the notch is to be prepared. Bending the test pieces while mounting on the holder is to be avoided.
Key
1 mounting plate
2 dummy test pieces
3 test pieces for testing
4 pencil line as a guide for introducing a diamond-sawn starter notch
Figure 2 — Mounting procedure for the set of test pieces
Mount the holder on a diamond saw. Saw a starter notch along the pencil line of width � 0,5 mm. The notch
should have the same depth of about 0,5 mm over its entire length. Figure 3 shows a schematic arrangement
for sawing. After sawing, clean the holder, test pieces and especially the notch.
©
4 ISO 2008 – All rights reserved
Dimensions in millimetres
a) Test pieces arranged on b) Machining a starter notch with
the test piece support a thin diamond saw blade
Key
A tensile surface
B holder
C diamond saw blade
D sawn notch
X dummy test pieces
Figure 3 — Schematic diagrams for sawing
NOTE 1 It is helpful if the thickness of the diamond saw blade is only a little larger than the thickness of the razor blade
used for notch honing. Otherwise, the razor-blade tip might skate over the surface of the pre-sawn notch and it might be
difficult to start polishing the V-notch. V-shaping the saw-blade tip can help if available saw blades are significantly thicker
than the razor blades.
Fix the test-piece holder in a vice or other suitable clamp. Fill the starter notch with the fine diamond paste as
shown in Figure 4 a).
To protect the fingers, place a razor blade in a holder or apply a heavy self-adhesive tape as shown in
Figure 4 b). Put the exposed edge of the razor blade in the starter notch and apply a light force.
NOTE 2 Excessive force can be counter-productive, causing the razor-blade tip to blunt more quickly. Using a force of
about 5N to 10 N on the razor blade while polishing is normally sufficient.
Hone the V-notch with the razor blade with a smooth gentle back-and-forth motion [white arrows in Figure 4 b)].
Move the razor blade as upright and level as possible.
NOTE 3 A drop of lubricating oil placed in the notch reduces any tendency for the razor blade to jerk or bind while honing.
©
ISO 2008 – All rights reserved 5
a) Applying diamond paste from a syringe to the b) Reciprocating a razor blade in
sawn notch the sawn notch
Key
1 heavy protection tape
2 razor blade
Figure 4 — Positioning a razor blade in the sawn notch
Examine the depth of the V-notch periodically with an optical microscope at both ends of the V-notch. If
possible, do not remove the test pieces from the test-piece holder for examination. If it is necessary to remove
them and further honing is required, remount the test pieces on the holder with a razor blade inserted in the
V-notch to act as a guide. If the total V-notch depth is less than 0,8 mm, continue to hone. The total final V-notch
depth should be between 0,8 mm and 1,2 mm.
NOTE 4 Honing by hand with a 4µm diamond paste produces a V-notch width S of ≈ 20µm. Using a finer diamond paste,
e.g. a 1µm one, usually does not decrease the width. If the V-notch width S is larger than about 30µm, it is suggested that
a new razor blade or different razor-blade brand be employed. In coarse-grained materials, large grains might pop out into
the notch during honing and limit the ability to obtain a sharp V-notch.
NOTE 5 Different materials will take different periods of time to prepare the notch. Generally, harder or tougher ceramics
take longer than softer, more easily machined ceramics. Polishing V-notches into alumina test pieces will take typically
≈ 30 min, and into silicon nitride ones typically ≈ 4h, for five test pieces and two dummies.
Remove the test pieces from the holder while avoiding bending them. Carefully clean the test pieces with
acetone in a small powerful ultrasonic bath. Take care not to damage the test pieces while cleaning, e.g. by
1h
allowing them to come into contact during ultrasonic cleaning. Dry the test pieces in the oven for at least at
◦
120 C.
NOTE 6 Cleaning of the V-notch can be difficult, especially when the tip radius is small. Alternative steps might be
necessary to flush or scrape out the diamond grains.
6.4 Preparing the V-notches by machine (optional)
The task of honing V-notches can be automated. An example of a machine and its principal requirements are
shown in Annex A.
NOTE 1 With a machine of sufficient rigidity employing a 1µm diamond paste for the final stages of notching, the notch
width can be reduced typically to 1µm for ceramics with a grain size of about 1µm to 2µm.
NOTE 2 By commencing the notching directly on the flat test-piece surfaces using a razor blade and medium grit size
diamond past
...




Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...