ISO 7217:2023/Amd 1:2024
(Amendment)Titanium and titanium alloys — Bar, rod and billet — Technical delivery conditions — Amendment 1: Effective utilization of ISO 23515 specifying the designation of chemical composition
Titanium and titanium alloys — Bar, rod and billet — Technical delivery conditions — Amendment 1: Effective utilization of ISO 23515 specifying the designation of chemical composition
Titane et alliages de titane — Barre, tige et billette — Conditions techniques de livraison — Amendement 1: Titre manque
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 7217
First edition
Titanium and titanium alloys — Bar,
2023-04
rod and billet — Technical delivery
conditions
AMENDMENT 1
2024-07
AMENDMENT 1: Effective utilization of
ISO 23515 specifying the designation
of chemical composition
Reference number
ISO 7217:2023/Amd.1:2024(en) © ISO 2024
ISO 7217:2023/Amd.1:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 7217:2023/Amd.1:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the
...
International
Standard
ISO 7217
First edition
Titanium and titanium alloys — Bar,
2023-04
rod and billet — Technical delivery
conditions
AMENDMENT 1
AMENDMENT 1: Effective utilization
of ISO 23515 specifying the
designation of chemical composition
PROOF/ÉPREUVE
Reference number
ISO 7217:2023/Amd.1:2024(en) © ISO 2024
ISO 7217:2023/Amd.1:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE
ii
ISO 7217:2023/Amd.1:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibi
...
ISO
INTERNATIONAL
STANDARD
First edition
:2023-04
AMENDMENT/PRF Amd 1
ISO/TC 79/SC 11
Secretariat: JISC
Date: 2024-04-30
Titanium and titanium alloys — Bar, rod and billet — Technical
delivery conditions
AMENDMENT 1: Effective utilization of ISO 23515 specifying the
designation of chemical composition
Titane et alliages de titane — Barre, tige et billette — Conditions
techniques de livraison
Reference
number ISO
7217:2023(
E)
PROOF
ISISOO 7217:7217:22023/023/AAmmdd.1:.1:2024(2024(EE))
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8 CH-1214 Vernier, Geneva Phone: +41 22 749 01 11
CH-1214 Vernier,
GenevaEmail:
copyright@iso.org Website:
www.iso.org
Phone: + 41 22 749 01 11
E-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ISISOO 7217:7217:22023/023/AAmmdd.1:.1:2024(2024(EE))
ii © ISO 2023 – All rights reserved
ISISOO 7217:7217:22023/023/AAmmdd.1:.1:2024(2024(EE))
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental,
in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the
ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO
documentsdocument should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/d
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.