Gasoline engines — Medium pressure liquid fuel supply connections — Part 1: 60° female cone connectors

ISO 18418-1:2014 specifies the dimensional requirements of medium-pressure pipe end-connections for gasoline (spark-ignition) engine fuel injection equipment. It is applicable to externally threaded end-connections having a 60° female cone, as well as to the pipe end assemblies of medium-pressure fuel injection pipes with outside diameters of up to and including 10 mm.

Moteurs à essence — Connexions pour des lignes de combustible liquide à moyenne pression — Partie 1: Raccords à cônes femelle de 60°

General Information

Status
Withdrawn
Publication Date
12-Nov-2014
Withdrawal Date
12-Nov-2014
Current Stage
9599 - Withdrawal of International Standard
Completion Date
21-Nov-2016
Ref Project

Relations

Buy Standard

Standard
ISO 18418-1:2014 - Gasoline engines -- Medium pressure liquid fuel supply connections
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 18418-1
First edition
2014-11-15
Gasoline engines — Medium pressure
liquid fuel supply connections —
Part 1:
60° female cone connectors
Moteurs à essence — Connections pour des lignes de combustible
liquide à moyenne pression —
Partie 1: Raccords à cônes femelle de 60°
Reference number
ISO 18418-1:2014(E)
©
ISO 2014

---------------------- Page: 1 ----------------------
ISO 18418-1:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 18418-1:2014(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative reference . 1
3 Requirements . 1
3.1 Dimensions and tolerances . 1
3.2 Materials . 3
4 Operating pressure . 3
5 Designation . 3
Bibliography . 4
© ISO 2014 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 18418-1:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - S
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.