ISO 18418-1:2016

Gasoline engines — Medium pressure liquid fuel supply connections — Part 1: 60° female cone connectors

ISO 18418-1:2016 specifies the dimensional requirements of medium-pressure pipe end-connections for gasoline (spark ignition) engine fuel injection equipment. It is applicable to externally threaded end-connections having a 60° female cone (see Figure 1), as well as to the pipe end assemblies of medium-pressure fuel injection pipes with outside diameters of up to and including 10 mm (see Table 1).

Moteurs à essence — Connexions pour des lignes de combustible liquide à moyenne pression — Partie 1: Raccords à cônes femelle de 60°

General Information

• Status: Published
• Publication Date: 20-Nov-2016
• ICS: 43.060.40 - Fuel systems
• Technical Committee: ISO/TC 22/SC 34 - Propulsion, powertrain and powertrain fluids
• Drafting Committee: ISO/TC 22/SC 34/WG 2 - Injection equipment
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 18-Apr-2022

Relations

• Revises: ISO 18418-1:2014 - Gasoline engines — Medium pressure liquid fuel supply connections — Part 1: 60° female cone connectors
• Effective Date: 05-Nov-2015

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 18418-1
Second edition
2016-12-01
Gasoline engines — Medium pressure
liquid fuel supply connections —
Part 1:
60° female cone connectors
Moteurs à essence — Connexions pour des lignes de combustible
liquide à moyenne pression —
Partie 1: Raccords à cônes femelle de 60°
Reference number
ISO 18418-1:2016(E)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 18418-1:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 18418-1:2016(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 1
4.1 Dimensions and tolerances . 1
4.2 Materials . 3
5 Operating pressure . 3
6 Designation . 3
Bibliography . 4
© ISO 2016 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 18418-1:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 22, Road vehicl
...