ISO/FDIS 24062

Measurement of fluid flow in closed conduits — Clamp-on ultrasonic transit-time meters for liquids and gases

This document specifies requirements and recommendations for non-intrusive (clamp-on) ultrasonic flowmeters (USMs), which utilize the transit time of ultrasonic signals to measure the flow of predominantly single-phase homogenous fluids (liquids and gases) in closed conduits. This document specifies performance, calibration, and output characteristics, and deals with installation conditions.

Mesurage du débit des fluides dans les conduites fermées — Débitmètres non intrusifs à ultrasons à temps de transit pour les liquides et les gaz

General Information

• Status: Not Published
• ICS: 17.120.10 - Flow in closed conduits
• Technical Committee: ISO/TC 30/SC 5 - Velocity and mass methods
• Drafting Committee: ISO/TC 30/SC 5 - Velocity and mass methods
• Current Stage: 5020 - FDIS ballot initiated: 2 months. Proof sent to secretariat
• Start Date: 03-Oct-2023
• Completion Date: 03-Oct-2023

Standards Content (Sample)

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 24062
ISO/TC 30/SC 5
Measurement of fluid flow in closed
Secretariat: SNV
conduits — Clamp-on ultrasonic
Voting begins on:
2023-10-03 transit-time meters for liquids and
gases
Voting terminates on:
2023-11-28
Mesurage du débit des fluides dans les conduites fermées —
Débitmètres non-intrusifs à ultrasons à temps de transit pour les
liquides et les gaz
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 24062:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 1 ----------------------
ISO/FDIS 24062:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 24062
ISO/TC 30/SC 5
Measurement of fluid flow in closed
Secretariat: SNV
conduits — Clamp-on ultrasonic
Voting begins on:
transit-time meters for liquids and
gases
Voting terminates on:
Mesurage du débit des fluides dans les conduites fermées —
Débitmètres non-intrusifs à ultrasons à temps de transit pour les
liquides et les gaz
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: [phone]
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: [e-mail]
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/FDIS 24062:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 2 ----------------------
ISO/FDIS 24062:2023(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.2 Meter design . 2
3.3 Thermodynamic conditions . . 2
3.4 Statistics . 3
3.5 Calibration . 4
3.6 Symbols and subscripts . 5
4 Principle of measurement .
...

ISO /FDIS 24062:2023(E)
Style Definition: Heading 1: Indent: Left: 0 pt, First
line: 0 pt, Tab stops: Not at 21.6 pt
ISO TC 30/SC 05/WG 15
Style Definition: Heading 2: Font: Bold, Tab stops: Not
at 18 pt
Secretariat: SNV
Style Definition: Heading 3: Font: Bold
Date: 2023-09-09xx
Style Definition: Heading 4: Font: Bold
Style Definition: Heading 5: Font: Bold
Measurement of fluid flow in closed conduits — Clamp-on ultrasonic transit-time meters
Style Definition: Heading 6: Font: Bold
for liquids and gases
Style Definition: ANNEX
Mesurage du débit des fluides dans les conduites fermées — Débitmètres non-intrusifs à ultrasons
Style Definition: AMEND Terms Heading: Font: Bold
à temps de transit pour les liquides et les gaz
Style Definition: AMEND Heading 1 Unnumbered:
Font: Bold
Formatted: French (Switzerland)
Formatted: French (Switzerland)
Formatted: French (Switzerland)
Formatted: Font: Cambria

---------------------- Page: 1 ----------------------
ISO/FDIS 24062:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part
of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or
mechanical, including photocopying, or posting on the internet or an intranet, without prior written
permission. Permission can be requested from either ISO at the address below or ISO’s member body
in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.orgwww.iso.org
Published in Switzerland
ii © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 24062:2023(E)
Contents
Foreword . vi
Introduction . vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 Quantities . 1
3.1.1 volume flowrate . 1
3.1.2 mean flow velocity . 1
3.1.3 path velocity . 2
3.1.4 Reynolds number . 2
3.2 Meter design . 2
3.2.1 ultrasonic path . 2
3.2.2 electronic unit . 2
3.3 Thermodynamic conditions . 2
3.3.1 metering conditions . 2
3.3.2 standard conditions . 2
3.4 Statistics . 3
3.4.1 error . 3
3.4.2 repeatability (of results of measurements) . 3
3.4.3 reproducibility (of results of measurements) . 3
3.4.4 resolution .
...