iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 15500-14:2012/Amd 1:2016

(Amendment)

Road vehicles — Compressed natural gas (CNG) fuel system components — Part 14: Excess flow valve — Amendment 1

Road vehicles — Compressed natural gas (CNG) fuel system components — Part 14: Excess flow valve — Amendment 1

Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 14: Valve de limitation de débit — Amendement 1

General Information

Status
Withdrawn
Publication Date
22-Mar-2016
Withdrawal Date
22-Mar-2016
ICS
43.060.40 - Fuel systems
Technical Committee
ISO/TC 22/SC 41 - Specific aspects for gaseous fuels
Drafting Committee
ISO/TC 22/SC 41/WG 3 - Fuel system components and refuelling connector for vehicles propelled by gaseous fuel
Current Stage
9599 - Withdrawal of International Standard
Completion Date
15-Sep-2020
Ref Project

Relations

Revised
ISO 15500-14:2020 - Road vehicles — Compressed natural gas (CNG) fuel system components — Part 14: Excess flow valve
Effective Date
09-Jun-2018
Amends
ISO 15500-14:2012 - Road vehicles — Compressed natural gas (CNG) fuel system components — Part 14: Excess flow valve
Effective Date
25-Dec-2021

Buy Standard

ISO 15500-14:2012/Amd 1:2016ISO 15500-14:2012/Amd 1:2016
PreviousNext
Standard
ISO 15500-14:2012/Amd 1:2016
English language
1 pages
sale 15% off
Preview
sale 15% off
Preview
ISO 15500-14:2012/Amd 1:2016ISO 15500-14:2012/Amd 1:2016
PreviousNext
Standard
ISO 15500-14:2012/Amd 1:2016
English language
1 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 15500-14
Second edition
2012-04-15
AMENDMENT 1
2016-04-01
Road vehicles — Compressed natural
gas (CNG) fuel system components —
Part 14:
Excess flow valve
AMENDMENT 1
Véhicules routiers — Composants des systèmes de combustible gaz
naturel comprimé (GNC) —
Partie 14: Valve de limitation de débit
AMENDEMENT 1
Reference number
ISO 15500-14:2012/Amd.1:2016(E)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 15500-14:2012/Amd.1:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 15500-14:2012/Amd.1:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possib
...

DRAFT AMENDMENT
ISO 15500-14:2012/DAM 1
ISO/TC 22/SC 41 Secretariat: UNI
Voting begins on: Voting terminates on:
2015-08-19 2015-11-19
Road vehicles — Compressed natural gas (CNG) fuel
system components —
Part 14:
Excess flow valve
AMENDMENT 1
Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) —
Partie 14: Valve de limitation de débit
AMENDEMENT 1
ICS: 43.060.40
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 15500-14:2012/DAM 1:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015

---------------------- Page: 1 ----------------------
ISO 15500-14:2012/DAM 1:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or me
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 20766-21:2023(Main)
Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 21: Pressure and/or temperature sensors

This document specifies general requirements for the pressure and/or temperature sensors liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to device which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

  • Standard
    4 pages
    English language
    sale 15% off
ISO
ISO 20766-15:2023(Main)
Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 15: Excess flow valve

This document specifies general requirements of the liquefied petroleum gas fuel component, excess flow valve, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to devices which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

  • Standard
    3 pages
    English language
    sale 15% off
ISO
ISO 20766-7:2023(Main)
Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 7: Remotely controlled service valve with excess flow valve

This document specifies general requirements and definitions of the liquefied petroleum gas fuel component: remotely controlled service valve with excess flow valve. This component is intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to device which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ISO
ISO 20766-8:2023(Main)
Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 8: Fuel pump

This document specifies general requirements for the fuel pump component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to device which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ISO
ISO 15500-21:2023(Main)
Road vehicles — Compressed natural gas (CNG) fuel system components — Part 21: Discharge line closures

This document specifies tests and requirements for discharge lines closures, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with the ISO 15403-1. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; c) stationary gas engines; d) container-mounting hardware; e) electronic fuel management; f) refuelling receptacles.

  • Standard
    4 pages
    English language
    sale 15% off
ISO
ISO 15500-13:2023(Main)
Road vehicles — Compressed natural gas (CNG) fuel system components — Part 13: Pressure relief device (PRD)

This document specifies tests and requirements for the pressure relief device (PRD), a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with ISO 15403-1. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; c) stationary gas engines; d) container-mounting hardware; e) electronic fuel management; f) refuelling receptacles.

  • Standard
    14 pages
    English language
    sale 15% off
ISO
ISO 20766-17:2022(Main)
Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 17: Gas dosage unit

This document specifies general requirements and definitions for the gas dosage unit when not combined with the gas injection device (a liquefied petroleum gas fuel component), intended for use on the types of motor vehicles defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to device which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

  • Standard
    3 pages
    English language
    sale 15% off
ISO
ISO 20766-6:2019/Amd 1:2022(Amendment)
Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 6: Pressure relief valves (PRV) — Amendment 1
  • Standard
    2 pages
    English language
    sale 15% off
ISO
ISO 20766-13:2022(Main)
Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 13: Multivalve

This document specifies general requirements for the multivalve component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to devices which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

  • Standard
    4 pages
    English language
    sale 15% off
ISO
ISO 20766-24:2022(Main)
Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 24: Gas tubes

This document specifies general requirements and definitions for the gas tube component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to devices which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

  • Standard
    5 pages
    English language
    sale 15% off