Extenders for paints — Specifications and methods of test — Part 21: Silica sand (unground natural quartz)

This part of ISO 3262 specifies requirements and corresponding methods of test for silica sand (unground natural quartz).

Matières de charge pour peintures — Spécifications et méthodes d'essai — Partie 21: Sable de silice (quartz naturel non broyé)

La présente partie de l'ISO 3262 prescrit les spécifications et les méthodes d'essai correspondantes pour le quartz naturel non broyé.

General Information

Status
Withdrawn
Publication Date
26-Apr-2000
Current Stage
9599 - Withdrawal of International Standard
Completion Date
26-May-2023
Ref Project

Relations

Effective Date
15-Apr-2008

Buy Standard

Standard
ISO 3262-21:2000 - Extenders for paints -- Specifications and methods of test
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 3262-21:2000 - Matieres de charge pour peintures -- Spécifications et méthodes d'essai
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3262-21
First edition
2000-04-15
Extenders for paints — Specifications and
methods of test —
Part 21:
Silica sand (unground natural quartz)
Matières de charge pour peintures — Spécifications et méthodes d'essai —
Partie 21: Sable de silice (quartz naturel non broyé)
Reference number
ISO 3262-21:2000(E)
©
ISO 2000

---------------------- Page: 1 ----------------------
ISO 3262-21:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3262-21:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 3262 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 3262-21 was prepared by Technical Committee ISO/TC 35, Paints and varnishes,
Subcommittee SC 2, Pigments and extenders.
Together with the other parts (see below), this part of ISO 3262 cancels and replaces ISO 3262:1975, which has
been technically revised. Part 1 comprises the definition of the term extender and a number of test methods that
are applicable to most extenders, whilst part 2 and the following parts specify requirements and, where appropriate,
particular test methods for individual extenders.
ISO 3262 consists of the following parts, under the general title Extenders for paints — Specifications and methods
of test:
� Part 1: Introduction and general test methods
� Part 2: Barytes (natural barium sulfate)
� Part 3: Blanc fixe
� Part 4: Whiting
� Part 5: Natural crystalline calcium carbonate
� Part 6: Precipitated calcium carbonate
� Part 7: Dolomite
� Part 8: Natural clay
� Part 9: Calcined clay
� Part 10: Natural talc/chlorite in lamellar form
� Part 11: Natural talc, in lamellar form, containing carbonates
� Part 12: Muscovite-type mica
� Part 13: Natural quartz (ground)
© ISO 2000 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 3262-21:2000(E)
� Part 14: Cristobalite
� Part 15: Vitreous silica
� Part 16: Aluminium hydroxides
� Part 17: Precipitated calcium silicate
� Part 18: Precipitated sodium aluminium silicate
� Part 19: Precipitated silica
� Part 20: Fumed silica
� Part 21: Silica sand (unground natural quartz)
� Part 22: Flux-calcined kieselguhr
iv © ISO 2000 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 3262-21:2000(E)
Extenders for paints — Specifications and methods of test —
Part 21:
Silica sand (unground natural quartz)
1 Scope
This part of ISO 3262 specifies requirements and corresponding methods of test for silica sand (unground natural
quartz).
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 3262. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 3262 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
ISO 787-2:1981, General methods of test for pigments and extenders — Part 2: Determination of matter volatile at
105 °C.
1)
ISO 787-3:— , General methods of test for pigments and extenders — Part 3: Determination
...

NORME ISO
INTERNATIONALE 3262-21
Première édition
2000-04-15
Matières de charge pour peintures —
Spécifications et méthodes d'essai —
Partie 21:
Sable de silice (quartz naturel non broyé)
Extenders for paints — Specifications and methods of test —
Part 21: Silica sand (unground natural quartz)
Numéro de référence
ISO 3262-21:2000(F)
©
ISO 2000

---------------------- Page: 1 ----------------------
ISO 3262-21:2000(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait la
responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.
© ISO 2000
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque
forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l’ISO à
l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
ImpriméenSuisse
ii © ISO 2000 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 3262-21:2000(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 3.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités
membres votants.
L’attention est appelée sur le fait que certains des éléments de la présente partie de l’ISO 3262 peuvent faire
l’objet de droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence.
La Norme internationale ISO 3262-21 a été élaborée par le comité technique ISO/TC 35, Peintures et vernis,
sous-comité SC 2, Pigments et matières de charge.
La présente partie de l’ISO 3262 et les autres parties (voir ci-dessous) annulent et remplacent l’ISO 3262:1975, qui
a fait l’objet d’une révision technique. La partie 1 comprend la définition du terme «matière de charge» et présente
un certain nombre de méthodes d’essai qui s’appliquent à la plupart des matières de charge; la partie 2 et les
parties suivantes prescrivent les exigences et, s’il y a lieu, les méthodes d’essai particulières s’appliquant à des
matières de charge données.
L’ISO 3262 comprend les parties suivantes, présentées sous le titre général Matières de charge pour peintures —
Spécifications et méthodes d’essai:
� Partie 1: Introduction et méthodes d’essai générales
� Partie 2: Barytine (sulfate de baryum naturel)
� Partie 3: Blanc fixe
� Partie 4: Craie
� Partie 5: Carbonate de calcium cristallin naturel
� Partie 6: Carbonate de calcium précipité
� Partie 7: Dolomite
� Partie 8: Kaolin naturel
� Partie 9: Kaolin calciné
� Partie 10: Talc et chlorite naturels sous forme lamellaire
� Partie 11: Talc naturel sous forme lamellaire, contenant des carbonates
© ISO 2000 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 3262-21:2000(F)
� Partie 12: Mica de type muscovite
� Partie 13: Quartz naturel broyé
� Partie 14: Cristobalite
� Partie 15: Silice vitreuse
� Partie 16: Alumines hydratées
� Partie 17: Silicate de calcium précipité
� Partie 18: Silicoaluminate de sodium précipité
� Partie 19: Silice précipitée
� Partie 20: Silice pyrogénée
� Partie 21: Sable de silice (quartz naturel non broyé)
� Partie 22: Kieselguhr, flux-calciné
iv © ISO 2000 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 3262-21:2000(F)
Matières de charge pour peintures — Spécifications et méthodes
d'essai —
Partie 21:
Sable de silice (quartz naturel non broyé)
1 Domaine d'application
La présente partie de l'ISO 3262 prescrit les spécifications et les méthodes d'essai correspondantes pour le quartz
naturel non broyé.
2 Références normatives
Les documents normatifs suivants contiennent des dispositions qui, par suite de la référence qui y est faite,
constituent des dispositions valables pour la présente partie de l'ISO 3262. Pour les références datées, les
amendements ultérieurs ou les révisions de ces publications ne s'appliquent pas. Toutefois, les parties prenantes
aux accords fondés sur la présente partie de l'ISO 3262 sont invitées à rechercher la possibilité d’appliquer les
éditions les plus récentes des documents normatifs indiqués ci-après. Pour les références non datées, la dernière
édition du document normatif en référence s'applique. Les membres de l’ISO et de la CEI possèdent le registre des
Normes internationales en vigueur.
ISO 787-2:1981, Méthodes générales d'essai des pigments et matières de charge — Partie 2: Déterm
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.