ISO/TS 13140-2:2012

Electronic fee collection — Evaluation of on-board and roadside equipment for conformity to ISO/TS 13141 — Part 2: Abstract test suite

ISO/TS 13140-2:2011 specifies the abstract test suite (ATS) to evaluate the conformity of on-board equipment (OBE) and roadside equipment (RSE) to ISO/TS 13141:2010. It provides a basis for conformance tests for dedicated short range communication (DSRC) equipment (on-board equipment and roadside equipment) to enable interoperability between different equipment supplied by different manufacturers.

Perception du télépéage — Évaluation des équipements embarqués et en bord de route quant à la conformité avec l'ISO/TS 13141 — Partie 2: Suite d'essai abstraite

General Information

• Status: Withdrawn
• Publication Date: 23-Feb-2012
• Withdrawal Date: 23-Feb-2012
• ICS: 03.220.20 - Road transport
• ICS: 35.240.60 - IT applications in transport
• Technical Committee: ISO/TC 204 - Intelligent transport systems
• Drafting Committee: ISO/TC 204/WG 5 - Fee and toll collection
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 22-Nov-2016

Relations

• Revised: ISO 13140-2:2016 - Electronic fee collection — Evaluation of on-board and roadside equipment for conformity to ISO 13141 — Part 2: Abstract test suite
• Effective Date: 05-Nov-2015
• Consolidates: ISO 17624:2004 - Acoustics — Guidelines for noise control in offices and workrooms by means of acoustical screens
• Effective Date: 06-Jun-2022

Standards Content (Sample)

TECHNICAL ISO/TS
SPECIFICATION 13140-2
First edition
2012-03-01

Electronic fee collection — Evaluation of
on-board and roadside equipment for
conformity to ISO/TS 13141 —
Part 2:
Abstract test suite
Perception du télépéage — Évaluation des équipements embarqués et
en bord de route quant à la conformité avec l'ISO/TS 13141 —
Partie 2: Suite d'essai abstraite




Reference number
ISO/TS 13140-2:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO/TS 13140-2:2012(E)

COPYRIGHT PROTECTED DOCUMENT


©  ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/TS 13140-2:2012(E)
Contents Page
Foreword . iv
Introduction . v
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Abbreviated terms . 4
5  Abstract Test Method (ATM). 4
5.1  General . 4
5.2  Test architecture . 4
5.3  Protocol Implementation Extra Information for Testing (PIXIT) . 4
6  Untestable Test Purposes (TP) . 5
7  ATS conventions . 5
7.1  General . 5
7.2  Naming conventions . 5
7.2.1  Declarations part . 5
7.2.2  Constraints part . 7
7.2.3  Dynamic part . 7
7.3  Implementation conventions . 8
7.3.1  Declaration part . 8
7.3.2  Constraint part . 8
7.3.3  Dynamic part . 8
Annex A (normative) Abstract Test Suite (ATS) for on-board units . 9
Annex B (normative) Abstract test suite (ATS) for roadside equipment . 10
Annex C (informative) PIXIT proforma for on-board units . 11
Annex D (informative) PIXIT proforma for roadside equipment . 13
Bibliography . 15

© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/TS 13140-2:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of document:
— an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members of
the parent committee casting a vote;
— an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting a
vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 13140-2 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 278, Road transport and traffic telematics, in collaboration with Technical Committee ISO/TC 204,
Intelligent transport systems, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
ISO/TS 13140 consists of the following parts, under the general title Electronic fee collection — Evaluation of
on-board and roadside equipment for conformity to ISO/TS 13141:
 Part 1: Test suite structure and test purposes
 Part 2: Abstract test suite
iv © ISO 2012 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/TS 13140-2:2012(E)
Introduction
ISO/TS 17575 is part of a set of standards that supports interoperability of autonomous EFC-systems. It
defines the EFC context data, their charge reports and their use of communication infrastructure.
The set of standards also supports short range communication links in the context of autonomous electronic
fee collection (EFC) on-board equipment (OBE) to enable spot checks for the enforcement process. The
application interface is defined in ISO/TS 13141:2010.
Within the set of EFC standards this part of ISO/TS 13140 defines the process and tests for conformity
evaluation of OBE and roadside equipment (RSE) that comply with the requirements in ISO/TS 13141:2010.
This part of ISO/TS 13140 is intended to
 assess OBE and RSE capabilities,
 assess OBE and RSE behaviour,
 serve as a guide for OBE and RSE conformance evaluation and type approval,
 achieve comparability between the results of the corresponding tests applied in different places at
different times, and
 facilitate communication between parties (for example between equipment manufacturers and test
houses).
This part of ISO/TS 13140 is based on
 ISO/TS 13141:2010,
 the set of dedicated short range communication (DSRC) standards defining the communication stack,
and
 ISO 9646.
This part of ISO/TS 13140 is based on using the tree and tabular combined notation (TTCN) that is a
standardized language suitable for specification of test cases and steps for assessment of protocol and
application behaviour. The TTCN language is also supported by modern automated tools that accelerate
software design, implementation and testing.

© ISO 2012 – All rights reserved v

---------------------- Page: 5 ----------------------
TECHNICAL SPECIFICATION ISO/TS 13140-2:2012(E)

Electronic fee collection — Evaluation of on-board and roadside
equipment for conformity to ISO/TS 13141 —
Part 2:
Abstract test suite
1 Scope
This part of ISO/TS 13140 specifies the abstract test suite (ATS) to evaluate the conformity of on-board
equipment (OBE) and roadside equipment (RSE) to ISO/TS 13141:2010.
It provides a basis for conformance tests for dedicated short range communication (DSRC) equipment (on-
board equipment and roadside equipment) to enable interoperability between different equipment supplied by
different manufacturers.
NOTE The OBE and RSE are subject to additional testing in order to ascertain that they fulfil the essential radio
requirements as set out in European Directives, a pre-requisite for CE marking and placing on the European market. They
are also likely to be subject to additional testing of physical, environmental endurance, quality assurance and control at
manufacturing, charge point integration, as part of factory, site and system acceptance testing. The definition of these
tests is outside the scope of this part of ISO/TS 13140.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO/IEC 9646-3:1998, Information technology — Open Systems Interconnection — Conformance testing
methodology and framework — Part 3: The Tree and Tabular Combined Notation (TTCN)
ISO/TS 13141:2010, Electronic fee collection — Localisation augmentation communication for autonomous
systems
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
access credentials
data that is transferred to on-board equipment (OBE), in order to establish the claimed identity of a
roadside (RSE) application process entity
[ISO 14906:2011, definition 3.1]
NOTE The access credentials carry information needed to fulfil access conditions in order to perform the operation
on the addressed element in the OBE. The access credentials can carry passwords as well as cryptographic based
information such as authenticators.
© ISO 2012 – All rights reserved 1

---------------------- Page: 6 ----------------------
ISO/TS 13140-2:2012(E)
3.2
attribute
application information formed by one or by a sequence of data elements, which is managed by different
actions used for implementation of a transaction
[ISO 14906:2011, definition 3.3]
3.3
authenticator
data appended to, or a cryptographic transformation of, a data unit that allows a recipient of the data unit to
prove the source and/or the integrity of the data unit and protect against forgery
[ISO 14906:2011, definition 3.4]
3.4
channel
information transfer path
[ISO 14906:2011, definition 3.5]
NOTE This term originally appeared in ISO/IEC 7498-2:1989, definition 3.3.13.
3.5
component
logical and physical entity composing an on-board equipment (OBE), supporting a specific functionality
[ISO 14906:2011, definition 3.6]
3.6
contract
expression of an agreement between two or more parties concerning the use of the road infrastructure
[ISO 14906:2011, definition 3.7]
3.7
element
DSRCdirectory containing application information in the form of attributes
[ISO 14906:2011, definition 3.11]
3.8
implementation conformance statement
statement made by the supplier of an implementation or system claimed to conform to a given specification,
stating which capabilities have been implemented
[ISO/TS 14907-2:2011, definition 3.10]
3.9
implementation conformance statement pro forma
document, in the form of a questionnaire, which when completed for an implementation or system becomes
an implementation conformance statement
[ISO/TS 14907-2, definition 3.11]
3.10
implementation extra information for testing
statement made by the supplier or an implementer of an implementation under test (IUT) which contains or
references all of the information (in addition to that given in the implementation conformance statement)
related to the IUT and its testing environment, which will enable the test laboratory to run an appropriate test
suite against the IUT
[ISO/TS 14907-2, definition 3.12]
2 © ISO 2012 – All rights reserved

---------------------- Page: 7 ----------------------
ISO/TS 13140-2:2012(E)
3.11
implementation extra information for testing pro forma
document, in the form of a questionnaire, which when completed for an implementation under test (IUT)
becomes an implementation extra information for testing
[ISO/TS 14907-2, definition 3.13]
3.12
on-board equipment
equipment located within the vehicle and supporting the information exchange with the RSE, it is composed of
the on-board unit (OBU) and other sub-units whose presence are considered optional for the execution of a
transaction
NOTE Adapted from ISO 14906:2011, definition 3.13.
3.13
on-board unit
minimum component of an on-board equipment (OBE), whose functionality always includes at least the
support of the DSRC interface
[ISO 14906:2011, definition 3.14]
3.14
roadside equipment
equipment located along the road transport network, for the purpose of communication and data exchanges
with on-board equipment (OBE)
[ISO 14906:2011, definition 3.16]
3.15
session
exchange of information and interaction occurring at a specific EFC station between the roadside equipment
and the user/vehicle
[ISO 14906:2011, definition 3.19]
3.16
transaction
whole of the exchange of information between the roadside equipment (RSE) and the on-board equipment
(OBE) necessary for the completion of an EFC operation over the dedicated short range communication
(DSRC)
[ISO 14906:2011, definition 3.24]
3.17
tester
combination of equipment and processes which is able to perform conformance tests according to
ISO/TS 13140-2
3.18
user
entity that uses transport services provided by the service provider according to the terms of a contract
NOTE Adapted from ISO 14906:2011, definition 3.26.
© ISO 2012 – All rights reserved 3

---------------------- Page: 8 ----------------------
ISO/TS 13140-2:2012(E)
4 Abbreviated terms
For the purposes of this document, the following abbreviated terms apply throughout the document unless
otherwise specified.
AC_CR Access Credentials
ADU Application Data Unit
ASN.1 Abstract Syntax Notation One
ATS  Abstract Test Suite
BI  Behaviour Invalid (i.e. Invalid Behaviour tests)
B-Kernel Broadcast Kernel
BST  Beacon Service Table
BV  Behaviour Valid (i.e. Valid Behaviour tests)
Cf  Confirm
DSRC Dedicated Short-Range communication
DUT Device Under Test
EID  Element Identifier
EFC Electronic Fee Collection
ICS  Implementation Conformance Statement
IUT  Implementation Under Test
MAC Medium Access Control
PIXIT Protocol Implementation extra Information for Testing
SAP Service Access Point
SCS Semiconductor Characterization System
TC  Test Case
TSS  Test Suite Structure
VST  Vehicle Service Table
5 Abstract Test Method (ATM)
5.1 General
This clause describes the ATM used to test the layers at the OBU side and at the RSE side.
5.2 Test architecture
Section 4 in ETSI TS 102 486-2-3 describes the test architecture for application layer testing. As TPs from
ETSI TS 102 486-2-3 are referenced to in ISO/TS 13140-1, the test architectures presented there are also
relevant for the corresponding TCs. For all specific TPs introduced in ISO/TS 13140-1, the test architecture
defined in ETSI TS 102 486-2-3 is relevant too.
5.3 Protocol Implementation Extra Information for Testing (PIXIT)
The supplier of the OBU and RSE, respectively, is responsible for providing a Protocol Implementation Extra
Information for Testing (PIXIT).
The supplier of the OBU and RSE shall complete a PIXIT; see Annex C and Annex D for examples of
p
...

TECHNICAL ISO/TS
SPECIFICATION 13140-2
First edition
2012-03-01

Electronic fee collection — Evaluation of
on-board and roadside equipment for
conformity to ISO/TS 13141 —
Part 2:
Abstract test suite
Perception du télépéage — Évaluation des équipements embarqués et
en bord de route quant à la conformité avec l'ISO/TS 13141 —
Partie 2: Suite d'essai abstraite




Reference number
ISO/TS 13140-2:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO/TS 13140-2:2012(E)


This CD-ROM contains the following files for ISO/TS 13140-2:2012:
1) Electronic annexes, zip files with HTML TTCN.GR and ASCII TTCN.MP representations;
2) Electronic annexes, zip files with HTML DUT information documentation.





COPYRIGHT PROTECTED DOCUMENT


©  ISO 2012
All rights reserved. Unless required for installation or otherwise specified, no part of this CD-ROM may be reproduced, stored in a retrieval
system or transmitted in any form or by any means without prior permission from ISO. Requests for permission to reproduce this product
should be addressed to
ISO copyright office  Case postale 56  CH-1211 Geneva 20  Switzerland
Internet [e-mail]
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
Published in Switzerland

ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/TS 13140-2:2012(E)
Installation
If this publication has been packaged as a zipped file, do NOT open the file from the CD-ROM, but copy it to
the desired location in
...