ISO/IEC FDIS 22603-1

Information technology -- Digital representation of product information

Technologies de l'information -- Représentation numérique de l'information produit

General Information

• Status: Published
• ICS: 35.040.50 - Automatic identification and data capture techniques
• Technical Committee: ISO/IEC JTC 1/SC 31 - Automatic identification and data capture techniques
• Drafting Committee: ISO/IEC JTC 1/SC 31/WG 8 - Application of AIDC standards
• Current Stage: 5020 - FDIS ballot initiated: 2 months. Proof sent to secretariat
• Start Date: 16-Jun-2021
• Completion Date: 16-Jun-2021

Standards Content (sample)

FINAL
INTERNATIONAL ISO/IEC
DRAFT
STANDARD FDIS
22603-1
ISO/IEC JTC 1/SC 31
Information technology —
Secretariat: ANSI
Digital representation of product
Voting begins on:
2021-06-16 information —
Voting terminates on:
Part 1:
2021-08-11
General requirements
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/IEC FDIS 22603-1:2021(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. ISO/IEC 2021
---------------------- Page: 1 ----------------------
ISO/IEC FDIS 22603-1:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2021

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO/IEC 2021 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC FDIS 22603-1:2021(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Technical content ................................................................................................................................................................................................. 2

4.1 Maintenance responsibility .......................................................................................................................................................... 2

4.2 Access instructions .............................................................................................................................................................................. 2

4.3 Structure and content ....................................................................................................................................................................... 2

4.4 Website reference ................................................................................................................................................................................. 3

4.5 Access via machine-readable code ........................................................................................................................................ 3

© ISO/IEC 2021 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC FDIS 22603-1:2021(E)
Foreword

ISO (the International Organization for Standardization) and IEC (the International Electrotechnical

Commission) form the specialized system for worldwide standardization. National bodies that are

members of ISO or IEC participate in the development of International Standards through technical

committees established by the respective organization to deal with particular fields of technical

activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international

organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the

work.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for

the different types of document should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives or www .iec .ch/ members

_experts/ refdocs).

Attention is drawn to the possibility that some of the elements of this document may be the subject

of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent

rights. Details of any patent rights identified during the development of the document will be in the

Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents) or the IEC

list of patent declarations received (see patents.iec.ch).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/

iso/ foreword .html. In the IEC, see www .iec .ch/ understanding -standards.

This document was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,

Subcommittee SC 31, Automatic identification and data capture techniques.

A list of all parts in the ISO/IEC 22603 series can be found on the ISO and IEC websites.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/ members .html and www .iec .ch/ national

-committees.
iv © ISO/IEC 2021 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/IEC FDIS 22603-1:2021(E)
Introduction

ISO/IEC 22603 is a multi-part International Standard that establishes the requirements for electronic

product labelling. Electronic product labelling is an alternative to having a product’s compliance

markings and other product information used to communicate product conformance to stated national

standards and regulations on the product’s nameplate or product label. Electronic product labelling can

exist in combination with traditional physical product markings and statements.
Electronic product labelling can be applicable to any type of product.

Product markings and technical statements can communicate product conformance to national

standards and regulations. While many products are decreasing in physical size, mandatory

requirements for additional product compliance markings and documents are growing, in part because:

— regulators are increasing the required number of product markings and statements on products to

designate compliance with the mandatory product regulations;

— third party test or certification organizations are developing registered trademark symbols to be

affixed on products that they have tested/certified;

— product conformance to new standards and regulations on domains, such as “Environmental,” leads

to new categories of product marks and statements;
— a growing number of global regulators each with unique labelling requirements.

The physical limitations to accommodate the proliferation of printed compliance labels and information

cause confusion among regulators and end-users. An alternative method using an electronic system to

communicate product compliance information, used in conjunction with existing labelling practices or

as an alternative to them, allows the regulatory objectives to be achieved with better uniformity of

execution, clarity of language, greater flexibility and control.
Some expected benefits include:
— envir
...