ISO 6336-1:1996/Cor 2:1999

Calculation of load capacity of spur and helical gears - Part 1: Basic principles, introduction and general influence factors - Technical Corrigendum 2

Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale — Partie 1: Principes de base, introduction et facteurs généraux d'influence — Rectificatif technique 2

Izračun nosilnosti ravnozobih in poševnozobih zobnikov - 1. del: Osnove, uvajanje in koeficienti - Tehnični popravek 2

General Information

• Status: Withdrawn
• Publication Date: 08-Sep-1999
• Withdrawal Date: 08-Sep-1999
• ICS: 21.200 - Gears
• Technical Committee: ISO/TC 60/SC 2 - Gear capacity calculation
• Drafting Committee: ISO/TC 60/SC 2/WG 6 - Gear calculations
• Current Stage: 9599 - Withdrawal of International Standard
• Start Date: 04-Sep-2006
• Completion Date: 13-Dec-2025
• Ref Project: SIST ISO 6336-1:2002/TC 2:2002 - Calculation of load capacity of spur and helical gears - Part 1: Basic principles, introduction and general influence factors - TECHNICAL CORRIGENDUM 2

Relations

• Corrects: ISO 6336-1:1996 - Calculation of load capacity of spur and helical gears - Part 1: Basic principles, introduction and general influence factors
• Effective Date: 06-Jun-2022
• Revised: ISO 6336-1:2006 - Calculation of load capacity of spur and helical gears - Part 1: Basic principles, introduction and general influence factors
• Effective Date: 15-Apr-2008
• Child: SIST ISO 6336-1:2002 - Calculation of load capacity of spur and helical gears -- Part 1: Basic principles, introduction and general influence factors
• Effective Date: 12-May-2008
• Child: ISO 6336-1:1996 - Calculation of load capacity of spur and helical gears - Part 1: Basic principles, introduction and general influence factors
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL STANDARD ISO 6336-1:1996
TECHNICAL CORRIGENDUM 2
Published 1999-09-01
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION � МЕЖДУНАРОДНАЯОРГАНИЗАЦИЯПОСТАНДАРТИЗАЦИИ � ORGANISATION INTERNATIONALE DE NORMALISATION
Calculation of load capacity of spur and helical gears —
Part 1:
Basic principles, introduction and general influence factors
TECHNICAL CORRIGENDUM 2
Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale —
Partie 1: Principes de base, introduction et facteurs généraux d'influence
RECTIFICATIF TECHNIQUE 2
Technical Corrigendum 2 to International Standard ISO 6336-1:1996 was prepared by Technical Committee
ISO/TC 60, Gears, Subcommittee SC 2, Gear capacity calculation.
Page 1, subclause 1.2
Replace the second line with the following:
“- spur or helical gears with transverse contact ratios less than 1,0;”
Page 8, clause 3
Replace the definition of m* with the following:
“mass moment of inertia per unit facewidth referenced to line of action”
ICS 21.200 Ref. No. ISO 6336-1:1996/Cor.2:1999(E)
© ISO 1999 – All rights reserved
Printed in Switzerland
ISO 6336-1:1996/Cor.2:1999(E)
Page 16, subclause 4.1.7.4
Replace “K ”with“K ”.
a A
Page 32, subclause 6.5.1
In the fourth line, to “vz//100uu1� ” add “= 10”.
ej
Page 38, subclause 7.2.2
In the first line, before “F ” add “prior to running-in”.
�x
Page 52, subclause 7.6.2.1 b)
12), 15) 14),15)
Replace “.of beari
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors -
TECHNICAL CORRIGENDUM 221.200GonilaGearsICS:Ta slovenski standard je istoveten z:ISO 6336-1:1996/Cor 2:1999SIST ISO 6336-1:2002/TC 2:2002en01-julij-2002SIST ISO 6336-1:2002/TC 2:2002SLOVENSKI
STANDARD
ICS21.200Ref.No.ISO6336-1:1996/Cor.2:1999(E)©ISO1999–AllrightsreservedPrintedinSwitzerlandINTERNATIONALSTANDARDISO6336-1:1996TECHNICALCORRIGENDUM2Published1999-09-01INTERNATIONALORGANIZATIONFORSTANDARDIZATIONORGANISATIONINTERNATIONALEDENORMALISATIONCalculationofloadcapacityofspurandhelicalgears—Part1:Basicprinciples,introductionandgeneralinfluencefactorsTECHNICALCORRIGENDUM2Calculdelacapacitédechargedesengrenagescylindriquesàdenturesdroiteethélicoïdale—Partie1:Principesdebase,introductionetfacteursgénérauxd'influenceRECTIFICATIFTECHNIQUE2TechnicalCorrigendum2toInternationalStandardISO6336-1:1996waspreparedbyTechnicalCommitteeISO/TC60,Gears,SubcommitteeSC2,Gearcapacitycalculation.Page1,subclause1.2Replacethesecondlinewiththefollowing:“-spurorhelicalgearswithtransversecontactratioslessthan1,0;”Page8,clause3Replacethedefinitionofm*withthefollowing:“massmomentofinertiaperunitfacewidthreferencedtolineofaction”SIST ISO 6336-1:2002/TC 2:2002

ISO6336-1:19
...