ISO/IEC 10373-6:2020/Amd 2:2020

Cards and security devices for personal identification — Test methods — Part 6: Contactless proximity objects — Amendment 2: Enhancements for harmonization

Cartes et dispositifs de sécurité pour l'identification personnelle — Méthodes d'essai — Partie 6: Objets sans contact de proximité — Amendement 2: Améliorations pour harmonisation

General Information

• Status: Published
• Publication Date: 26-Nov-2020
• ICS: 35.240.15 - Identification cards. Chip cards. Biometrics
• Technical Committee: ISO/IEC JTC 1/SC 17 - Cards and security devices for personal identification
• Drafting Committee: ISO/IEC JTC 1/SC 17/WG 8 - Integrated circuit cards without contacts
• Current Stage: 6060 - International Standard published
• Start Date: 27-Nov-2020
• Due Date: 10-Oct-2021
• Completion Date: 27-Nov-2020

Relations

• Amends: ISO/IEC 10373-6:2020 - Cards and security devices for personal identification — Test methods — Part 6: Contactless proximity objects
• Effective Date: 11-Dec-2021

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 10373-6
Fourth edition
2020-07
AMENDMENT 2
2020-11
Cards and security devices for
personal identification — Test
methods —
Part 6:
Contactless proximity objects
AMENDMENT 2: Enhancements for
harmonization
Cartes et dispositifs de sécurité pour l'identification personnelle —
Méthodes d'essai —
Partie 6: Objets sans contact de proximité
AMENDEMENT 2: Améliorations pour harmonisation
Reference number
ISO/IEC 10373-6:2020/Amd.2:2020(E)
©
ISO/IEC 2020

---------------------- Page: 1 ----------------------
ISO/IEC 10373-6:2020/Amd.2:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO/IEC 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 10373-6:2020/Amd.2:2020(E)

Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that
are members of ISO or IEC participate in the development of International Standards through
technical committees established by the respective organization to deal with particular fields of
technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other
international organizations, governmental and non-governmental, in liaison with ISO and IEC, also
take part in the work.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for
the different types of document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject
of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent
rights. Details of any patent rights identified during the development of the document will be in the
Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents) or the IEC
list of patent declarations received (see http:// patents .iec .ch).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 17, Cards and security devices for personal identification.
A list of all parts in the ISO 10373 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
© ISO/IEC 2020 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC 10373-6:2020/Amd.2:2020(E)
Cards and security devices for personal identification —
Test methods —
Part 6:
Contactless proximity objects
AMENDMENT 2: Enhancements for harmonization

4.7, Table 3
Add the following row at the end of the table:
"
Parameter Description Unit
Type A collision Collision resolution for Type A
resolution
supported
"

H.2.3.4, Table H.8
Replace the table with the following:
"
Explanation Test result
Only when the PCD: PASS
—  starts the bit frame anticollision loop or
—  resets the operating field
Any other case FAIL
"

H.2.4.1
Add the following sentence at the end of the paragraph:
"Procedure 4 defined in H.2.4.3.4 is only applicable to PCDs supporting Type A collision resolution; and
Procedure 5 defined in H.2.4.3.5 is only applicable to PCDs not supporting Type A collision resolution
(see Table 3)."
© ISO/IEC 2020 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO/IEC 10373-6:2020/Amd.2:2020(E)

H.2.4.3.5
Add the following paragraph at the beginning of the subclause:
"This procedure is only applicable to PCDs supporting Type A collision resolution (see Table 3)."

H.2.4.3.6
Add the following new subclause after H.2.4.3.5:
"
H.2.4.3.6  Procedure 5 (Detection of full bitwise anticollision loop for PICC)
This procedure is only applicable to PCDs not supporting Type A collision resolution (see Table 3).
Use the following sequence:
a) The UT performs the activation procedure according to H.1.8.1.
b) The LT waits until the PCD sends a valid REQA/WUPA command frame
c) The LT answers with ATQA indicating bit frame anticollision and UID size: single (bits b8 and b7
equal (00)b).
d) The PCD shall send ANTICOLLISION command: '93 20'.
e) The LT answers by a stream of 40 bits by emulating a collision on every bit, including parity bits.
f) The PCD shall reset the operating field.
Table H.13 gives part of the procedure as a scenario.
Table H.13 — Scenario H.5: Detection of full bitwise anticollision loop for PICC (Procedure 5)
Test PCD LT
REQA/WUPA →
REQA/WUPA
← ATQA (single size UID)
ANTICOLLISION command
→
('93 20')
ANTICOLLISION
← 40 bits full collision frame
RESET Reset of the operating field →
"

H.2.4.4, Table H.13
Replace the table with the following:
"
Explanation Test result
Only when the PCD’s behavior matches each PASS
applicable procedure expected scenario
Any other case FAIL
"
2 © ISO/IEC 2020 – All rights reserved

---------------------- Page: 5 ----------------------
ISO/IEC 10373-6:2020/Amd.2:2020(E)

H.2.5.3.2
Delete the subclause "H.2.5.3.2 Procedure 1" and renumber the subsequent subclauses.

H.2.10.3
Replace step g) with the following:
"g) The PCD either shall send R(NAK) or shall send an S(DESELECT) request or shall reset the
0
operating field."

H.2.10.3, Table H.24
Replace the last row with the following:
"
PCD LT
R(NAK) ('BA' CID CRC or 'B2' CRC)
0
or
S(DESELECT) →
or
reset of the operating field
“

H.3.3.3.2
Replace step l) with the following:
"l) The PCD either shall send an S(DESELECT) request without NAD and CID or shall reset the
operating field."

H.3.3.3.2, Table 28
Replace the last row with the followi
...

INTERNATIONAL ISO/IEC
STANDARD 10373-6
Fourth edition
2020-07
AMENDMENT 2
ISO pub-date
Cards and security devices for
personal identification — Test
methods —
Part 6:
Contactless proximity objects
AMENDMENT 2: Enhancements for
harmonization
Cartes et dispositifs de sécurité pour l'identification personnelle —
Méthodes d'essai —
Partie 6: Objets sans contact de proximité
AMENDEMENT 2: Améliorations pour harmonisation
PROOF/ÉPREUVE
Reference number
ISO/IEC 10373-6:2020/Amd.2:2020(E)
©
ISO/IEC 2020

---------------------- Page: 1 ----------------------
ISO/IEC 10373-6:2020/Amd.2:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii PROOF/ÉPREUVE © ISO/IEC 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 10373-6:2020/Amd.2:2020(E)

Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that
are members of ISO or IEC participate in the development of International Standards through
technical committees established by the respective organization to deal with particular fields of
technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other
international organizations, governmental and non-governmental, in liaison with ISO and IEC, also
take part in the work.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for
the different types of document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject
of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent
rights. Details of any patent rights identified during the development of the document will be in the
Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents) or the IEC
list of patent declarations received (see http:// patents .iec .ch).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 17, Cards and security devices for personal identification.
A list of all parts in the ISO 10373 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
© ISO/IEC 2020 – All rights reserved PROOF/ÉPREUVE iii

---------------------- Page: 3 ----------------------
ISO/IEC 10373-6:2020/Amd.2:2020(E)
Cards and security devices for personal identification —
Test methods —
Part 6:
Contactless proximity objects
AMENDMENT 2: Enhancements for harmonization
4.7, Table 3
Add the following row at the end of the table:
"
Parameter Description Unit
Type A collision Collision resolution for Type A
resolution
supported
"
H.2.3.4, Table H.8
Replace the table with the following:
"
Explanation Test result
Only when the PCD: PASS
—  starts the bit frame anticollision loop or
—  resets the operating field
Any other case FAIL
"
H.2.4.1
Add the following sentence at the end of the paragraph:
"Procedure 4 defined in H.2.4.3.4 is only applicable to PCDs supporting Type A collision resolution; and
Procedure 5 defined in H.2.4.3.5 is only applicable to PCDs not supporting Type A collision resolution
(see Table 3)."
© ISO/IEC 2020 – All rights reserved PROOF/ÉPREUVE 1

---------------------- Page: 4 ----------------------
ISO/IEC 10373-6:2020/Amd.2:2020(E)

H.2.4.3.5
Add the following paragraph at the beginning of the subclause:
"This procedure is only applicable to PCDs supporting Type A collision resolution (see Table 3)."
H.2.4.3.6
Add the following new subclause after H.2.4.3.5:
"
H.2.4.3.6  Procedure 5 (Detection of full bitwise anticollision loop for PICC)
This procedure is only applicable to PCDs not supporting Type A collision resolution (see Table 3).
Use the following sequence:
a) The UT performs the activation procedure according to H.1.8.1.
b) The LT waits until the PCD sends a valid REQA/WUPA command frame
c) The LT answers with ATQA indicating bit frame anticollision and UID size: single (bits b8 and b7
equal (00)b).
d) The PCD shall send ANTICOLLISION command: '93 20'.
e) The LT answers by a stream of 40 bits by emulating a collision on every bit, including parity bits.
f) The PCD shall reset the operating field.
Table H.13 gives part of the procedure as a scenario.
Table H.13 — Scenario H.5: Detection of full bitwise anticollision loop for PICC (Procedure 5)
Test PCD LT
REQA/WUPA →
REQA/WUPA
← ATQA (single size UID)
ANTICOLLISION command
→
('93 20')
ANTICOLLISION
← 40 bits full collision frame
RESET Reset of the operating field →
"
H.2.4.4, Table H.13
Replace the table with the following:
"
Explanation Test result
Only when the PCD’s behavior matches each PASS
applicable procedure expected scenario
Any other case FAIL
"
2 PROOF/ÉPREUVE © ISO/IEC 2020 – All rights reserved

---------------------- Page: 5 ----------------------
ISO/IEC 10373-6:2020/Amd.2:2020(E)

H.2.5.3.2
Delete the subclause "H.2.5.3.2 Procedure 1" and renumber the subsequent subclauses.

H.2.10.3
Replace step g) with the following:
"g) The PCD either shall send R(NAK) or shall send an S(DESELECT) request or shall reset the
0
operating field."

H.2.10.3, Table H.24
Replace the last row with the following:
"
PCD LT
R(NAK) ('BA' CID CRC or 'B2' CRC)
0
or
S(DESELECT) →
or
reset of the operating field
“

H.3.3.3.2
Replace step l) with the following:
"l) The PCD either shall send an S(DESELECT) request without NAD and CID or shall reset the
operating field."

H.3.3.3.2, Table 28
Replace the last row with the following:
"
PCD LT
Optional R(NAK) wi
...