ISO/IEC 14443-3:2011/Amd 6:2014

Identification cards — Contactless integrated circuit cards — Proximity cards — Part 3: Initialization and anticollision — Amendment 6: Bit rates of 3fc/4, fc, 3fc/2 and 2fc from PCD to PICC

Cartes d'identification — Cartes à circuit(s) intégré(s) sans contact — Cartes de proximité — Partie 3: Initialisation et anticollision — Amendement 6: Débits binaires de 3fc/4, fc, 3fc/2 et 2fc de PCD à PICC

General Information

• Status: Withdrawn
• Publication Date: 25-May-2014
• Withdrawal Date: 25-May-2014
• ICS: 35.240.15 - Identification cards. Chip cards. Biometrics
• Technical Committee: ISO/IEC JTC 1/SC 17 - Cards and security devices for personal identification
• Drafting Committee: ISO/IEC JTC 1/SC 17/WG 8 - Integrated circuit cards without contacts
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 27-May-2016

Relations

• Revised: ISO/IEC 14443-3:2016 - Identification cards — Contactless integrated circuit cards — Proximity cards — Part 3: Initialization and anticollision
• Effective Date: 21-Nov-2015
• Amends: ISO/IEC 14443-3:2011 - Identification cards — Contactless integrated circuit cards — Proximity cards — Part 3: Initialization and anticollision
• Effective Date: 10-Jul-2021

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 14443-3
Second edition
2011-04-15
AMENDMENT 6
2014-06-01
Identification cards — Contactless
integrated circuit cards — Proximity
cards —
Part 3:
Initialization and anticollision
AMENDMENT 6: Bit rates of 3fc/4, fc,
3fc/2 and 2fc from PCD to PICC
Cartes d’identification — Cartes à circuit(s) intégré(s) sans contact —
Cartes de proximité —
Partie 3: Initialisation et anticollision
AMENDEMENT 6: Débits binaires de 3fc/4, fc, 3fc/2 et 2fc de PCD à
PICC
Reference number
ISO/IEC 14443-3:2011/Amd.6:2014(E)
©
ISO/IEC 2014

---------------------- Page: 1 ----------------------
ISO/IEC 14443-3:2011/Amd.6:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2014 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 14443-3:2011/Amd.6:2014(E)

Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are
members of ISO or IEC participate in the development of International Standards through technical
committees established by the respective organization to deal with particular fields of technical
activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international
organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the
work. In the field of information technology, ISO and IEC have established a joint technical committee,
ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the national bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
Amendment 6 to ISO/IEC 14443-3:2011 was prepared by Joint Technical Committee ISO/IEC JTC 1,
Information technology, Subcommittee SC 17, Cards and personal identification.
© ISO/IEC 2014 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC 14443-3:2011/Amd.6:2014(E)
Identification cards — Contactless integrated circuit cards
— Proximity cards —
Part 3:
Initialization and anticollision
AMENDMENT 6: Bit rates of 3fc/4, fc, 3fc/2 and 2fc from PCD to
PICC
Page 5, 6.1 (amended by ISO/IEC 14443-3:2011/Amd.2:2012)
Add the following after Table 1:
“For bit rates of 3fc/4, fc, 3fc/2 and 2fc see E.1.”
Page 7, 6.2.1.1 (amended by ISO/IEC 14443-3:2011/Amd.2:2012)
Add the following after second paragraph:
“For bit rates of 3fc/4, fc, 3fc/2 and 2fc see E.2.1.1.”
Page 9, 6.2.1.1 (amended by ISO/IEC 14443-3:2011/Amd.2:2012)
Complete the enumeration of bit rates in Table 2 by adding bit rates of 3fc/4, fc, 3fc/2 and 2fc in last row.
Page 11, 6.2.3.2.2
Add
...

DRAFT AMENDMENT ISO/IEC 14443-3:2011/DAM 6
ISO/IEC JTC 1 Secretariat: ANSI

Voting begins on Voting terminates on
2012-06-20 2012-11-20
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION  МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ  ORGANISATION INTERNATIONALE DE NORMALISATION
INTERNATIONAL ELECTROTECHNICAL COMMISSION  МЕЖДУНАРОДНАЯ ЭЛЕКТРОТЕХНИЧЕСКАЯ КОММИСИЯ  COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE


Identification cards — Contactless integrated circuit cards —
Proximity cards —
Part 3:
Initialization and anticollision
AMENDMENT 6: Bit rates of 3fc/4, fc, 3fc/2 and 2fc
Cartes d'identification — Cartes à circuit(s) intégré(s) sans contact — Cartes de proximité —
Partie 3: Initialisation et anticollision
AMENDEMENT 6: Débits binaires de 3fc/4 et fc

ICS 35.240.15


To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.


THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME
STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
International Organization for Standardization, 2012
©
International Electrotechnical Commission, 2012

---------------------- Page: 1 ----------------------
ISO/IEC 14443-3:2011/DAM 6

Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO/IEC 2012 — All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 14443-3:2011/DAM 6
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commi
...