ISO 15184:1998
(Main)Paints and varnishes — Determination of film hardness by pencil test
Paints and varnishes — Determination of film hardness by pencil test
Peintures et vernis — Détermination de la dureté du feuil par l'essai de dureté crayon
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 15184
First edition
1998-11-01
Paints and varnishes — Determination
of film hardness by pencil test
Peintures et vernis — Détermination de la dureté du feuil
par l’essai de dureté crayon
A
Reference number
ISO 15184:1998(E)
---------------------- Page: 1 ----------------------
ISO 15184:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 15184 was prepared by Technical Committee ISO/TC 35, Paints and varnishes,
Subcommittee SC 9, General test methods for paints and varnishes.
Annex A forms an integral part of this International Standard.
© ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii
---------------------- Page: 2 ----------------------
©
INTERNATIONAL STANDARD ISO ISO 15184:1998(E)
Paints and varnishes — Determination of film hardness
by pencil test
1 Scope
1.1 This International Standard is one of a series of standards dealing with the sampling and testing of paints,
varnishes and related products.
It specifies a method for determining the film hardness by pushing pencils of known hardness over the film.
The test can be performed on a single coating of a paint, varnish or related product, or on the upper layer of a
multicoat system.
1.2 This rapid, inexpensive test has been found to be useful in comparing the pencil hardness of different
coatings.
It is more useful in providing relative ratings for a series of coated panels exhibiting significant differences in pencil
hardness.
The method is applicable only to smooth surfaces.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain
registers of currently valid International Standards.
ISO 1512:1991, Paint and varnishes — Sampling of products in liquid or paste form.
ISO 1513:1992, Paints and varnishes — Examination and preparation of samples for testing.
ISO 1514:1993, Paints and varnishes — Standard panels for testing.
ISO 2808:1997, Paints and varnishes — Determination of film thickness.
3 Definition
For the purposes of this International Standard, the following definition applies:
3.1 pencil hardness: The resistance of the surface of a paint film to marking, or the formation of some other
defect, as a result of the action of a pencil with a lead of specified dimensions, shape and hardness which is pushed
across the surface.
1
---------------------- Page: 3 ----------------------
©
ISO
ISO 15184:1998(E)
Marking by pencil leads covers a range of defects in the surface of the paint film.
These defects are defined as follows:
a) Plastic deformation: a permanent indentation in the paint surface without cohesive fracture.
b) Cohesive fracture: the presence of a visible scratch or rupture in the surface of the paint film, material having
been removed from the paint film.
c) Combinations of the above.
These defects can occur simultaneously.
4 Principle
The product or system under test is applied at uniform thickness to flat panels of uniform surface texture.
After drying/curing, the pencil hardness is determined by pushing pencils of increasing hardness over the paint film,
with the panel in a horizontal position.
During the test, the pencil is mounted so that it presses down on the paint surface at an angle of 45° with a load of
750 g.
The hardness of the pencils is increased in steps until the coating is marked by defects of the kind defined in 3.1.
5 Required supplementary information
For any particular application, the test method specified in this International Standard needs to be completed by
supplementary information.
The items of supplementary information are given in annex A.
6 Apparatus
6.1 Test instrument: The test is best performed using a mechanical device. An example of a suitable device is
shown in figure 1 (see also note).
NOTE — Although the test is preferably performed using a mechanical device, it can also be performed by hand. Other types
of test instrument may also be used, provided they give similar relative rating results.
The device shown consists of a metal block fitted with two wheels, one on each side. In the middle of the metal
block, there is a cylindrical hole inclined at an angle of (45 ± 1)°.
With the help of a clamp, pencils can be fixed in the instrument so that they are always in the same position.
Mounted on the top of the instrument is a level which is used to ensure that the test is carried out with the
instrument horizontal.
The instrument shall be designed so that, with the instrument in the horizontal position, the tip of the pencil exerts a
load of (750 ± 10) g on the paint surface.
2
---------------------- Page: 4 ----------------------
©
ISO
ISO 15184:1998(E)
6.2 Set of wood drawing pencils, of the following hardnesses (see note):
9B - 8B - 7B - 6B - 5B - 4B - 3B - 2B - B - HB - F - H - 2H - 3H - 4H - 5H - 6H - 7H - 8H - 9H
Softer Harder
NOTE — Pencils made by various manufacturers may be used by agreement between the interested parties, provided they
give similar relative rating results.
Some examples of pencil makes and manufacturers which have been found suitable are as follows:
Microtomic, manufactured by Faber Castell;
Turquoise T-2375, manufactured by Empire Berol, USA;
KOH-I-NOOR, type 1500, manufactured by Hardtmuth AG;
Uni, manufactured by the Mitsubishi Pencil Co.
For comparative testing, it is recommended that pencils from the same manufacturer be used. Variations may be found
between manufacturers and between batches from the same manufacturer.
1)
6.3 Special mechanical sharpener , which will remove the wood only, leaving the cylindrical pencil lead intact
(see figure 2).
6.4 Abrasive paper, grit No. 400.
6.5 Soft cloth or swab of cotton wool, to clean the panel after the test, using a solvent to which the coating is
inert.
Dimensions in millimetres
Key
1 Rubber O-ring 6 Clamp
2 Pen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.