ISO/IEC 10373-6:2011/Amd 3:2012
(Amendment)Identification cards — Test methods — Part 6: Proximity cards — Amendment 3: Exchange of additional parameters, block numbering, unmatched AFI and TR2
Identification cards — Test methods — Part 6: Proximity cards — Amendment 3: Exchange of additional parameters, block numbering, unmatched AFI and TR2
Cartes d'identification — Méthodes d'essai — Partie 6: Cartes de proximité — Amendement 3: Échange de paramètres additionnels, numérotation des blocs, AFI non correspondant et TR2
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 10373-6
Second edition
2011-01-15
AMENDMENT 3
2012-08-01
Identification cards — Test methods —
Part 6:
Proximity cards
AMENDMENT 3: Exchange of additional
parameters, block numbering, unmatched
AFI and TR2
Cartes d'identification — Méthodes d'essai —
Partie 6: Cartes de proximité
AMENDEMENT 3: Échange de paramètres additionnels, numérotation
des blocs, AFI non correspondant et TR2
Reference number
ISO/IEC 10373-6:2011/Amd.3:2012(E)
©
ISO/IEC 2012
---------------------- Page: 1 ----------------------
ISO/IEC 10373-6:2011/Amd.3:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2012 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 10373-6:2011/Amd.3:2012(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
Amendment 3 to ISO/IEC 10373-6:2011 was prepared by Joint Technical Committee ISO/IEC JTC 1,
Information technology, Subcommittee SC 17, Cards and personal identification.
© ISO/IEC 2012 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC 10373-6:2011/Amd.3:2012(E)
Identification cards — Test methods —
Part 6:
Proximity cards
AMENDMENT 3: Exchange of additional parameters, block
numbering, unmatched AFI and TR2
Page 91, G.3.3.2.2
Add the following note after Table G.7:
NOTE The block number may be 0 or 1 dependent on block numbering rules defined in ISO/IEC 14443-4:2008,
7.5.3.
Page 116, G.4.4.1.2
Add the following note after Table G.38:
NOTE The block number may be 0 or 1 dependent on block numbering rules defined in ISO/IEC 14443-4:2008,
7.5.3.
Page 116, G.4.4.2.2
e
Add table footnote “ ” to REQB and WUPB in Transition column of first and second rows in Table G.39.
f
Add table footnote “ ” to REQB(Unmatched AFI) and WUPB(Unmatched AFI) in Transition column of tenth and
eleventh rows in Table G.39.
e f
Add table footnotes “ ” and “ ” in last row in Table G.39:
e
All matched AFIs as defined by the PICC manufacturer shall be tested.
f
The unmatched AFI used in this test shall not be an RFU value. If the PICC accepts all AFIs this test is not applicable.
Page 118, G.4.4.3.2
e
Add table footnote “ ” to REQB and WUPB in Transition column of first and second rows in Table G.41.
f
Add table footnote “ ” to REQB(Unmatched AFI) and WUPB(Unmatched AFI) in Transition column of twelfth
and thirteenth rows in Table G.41.
e f
Add table footnotes “ ” and “ ” in last row in Table G.41:
e
All matched AFIs as defined by the PICC manufacturer shall be tested.
f
The unmatched AFI used in this test shall not be an RFU value. If the PICC accepts all AFIs this test is not applicable.
© ISO/IEC 2012 – All rights reserved 1
---------------------- Page: 4 ----------------------
ISO/IEC 10373-6:2011/Amd.3:2012(E)
Page 119, G.4.4.4.2
e
Add table footnote “ ” to REQB and WUPB in Transition column of first and second rows in Table G.43.
f
Add table footnote “” to REQB(Unmatched AFI) and WUPB(Unmatched AFI) in Transition column of
fourteenth and fifteenth rows in Table G.43.
e f
Add table footnotes “ ” and “ ” in last row in Table G.43:
e
All matched AFIs as defined by the PICC manufacturer shall be tested.
f
The unmatched AFI us
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.