ISO 14317:2015
(Main)Sintered metal materials excluding hardmetals — Determination of compressive yield strength
Sintered metal materials excluding hardmetals — Determination of compressive yield strength
ISO 14317:2015 specifies a method for the determination of the compressive yield strength of sintered metal materials, excluding hardmetals. This method is applicable to sintered materials (excluding hardmetals) that might or might not have been subjected to heat treatment after sintering and also to materials that have been sized or coined after sintering.
Matériaux métalliques frittés, à l'exclusion des métaux-durs — Détermination de la limite d'élasticité en compression
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 14317
Second edition
2015-04-01
Sintered metal materials excluding
hardmetals — Determination of
compressive yield strength
Matériaux métalliques frittés, à l’exclusion des métaux-durs —
Détermination de la limite d’élasticité en compression
Reference number
ISO 14317:2015(E)
©
ISO 2015
---------------------- Page: 1 ----------------------
ISO 14317:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 14317:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Test method . 1
4 Test piece . 1
5 Procedure. 1
6 Expression of results . 2
7 Test report . 2
8 Precision statement . 2
Bibliography . 5
© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 14317:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT), see the following URL: Foreword — Supplementary information.
The committee responsible for this document is ISO/TC 119, Powder metallurgy, Subcommittee SC 3,
Sampling and testing methods for sintered metal materials (excluding hardmetals).
This second edition cancels and replaces the first edition (ISO 14317:2006), which has been
technically revised.
iv © ISO 2015 – Al
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.