iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO/TR 20152-3:2013

(Main)

Timber structures — Bond performance of adhesives — Part 3: Use of alternative species for bond tests

Timber structures — Bond performance of adhesives — Part 3: Use of alternative species for bond tests

ISO/TR 20152-3:2013 describes the procedures necessary for the recognition of new wood species by ISO 20152‑1 and ISO 20152‑2 for the evaluation of structural wood adhesives.

Structures en bois — Performance d'adhérence des adhésifs — Partie 3: Usage des essences alternatives pour les essais de joints de collage

General Information

Status
Published
Publication Date
17-Apr-2013
ICS
91.080.20 - Timber structures
Technical Committee
ISO/TC 165 - Timber structures
Drafting Committee
ISO/TC 165 - Timber structures
Current Stage
9093 - International Standard confirmed
Completion Date
14-May-2021
Ref Project

Relations

Consolidated By
ISO 19011:2018 - Guidelines for auditing management systems
Effective Date
06-Jun-2022

Buy Standard

ISO/TR 20152-3:2013 - Timber structures -- Bond performance of adhesivesISO/TR 20152-3:2013 - Timber structures -- Bond performance of adhesives
PreviousNext
Technical report
ISO/TR 20152-3:2013 - Timber structures -- Bond performance of adhesives
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

TECHNICAL ISO/TR
REPORT 20152-3
First edition
2013-05-01
Timber structures — Bond
performance of adhesives —
Part 3:
Use of alternative species for bond tests
Structures en bois — Performance d’adhérence des adhésifs —
Partie 3: Usage des essences alternatives pour les essais de joints de
collage
Reference number
ISO/TR 20152-3:2013(E)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO/TR 20152-3:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/TR 20152-3:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2, www.iso.org/directives.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received, www.iso.org/patents.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 165, Timber structures.
ISO 20152 consists of the following parts, under the general title Timber structures — Bond performance
of adhesives:
— Part 1: Basic requirements
— Part 2: Additional requirements
— Part 3: Use of alternative species for bond tests [Technical Report]
© ISO 2013 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/TR 20152-3:2013(E)

Introduction
This Technical Report was prepared to simplify the assessment of adhesive bonds in countries where the
test species described in ISO 20152-1 and ISO 20152-2 may be difficult to obtain. It sets out procedures
for selecting substitute species available locally.
iv © ISO 2013 – All rights reserved

---------------------- Page: 4 ----------------------
TECHNICAL REPORT ISO/TR 20152-3:2013(E)
Timber structures — Bond performance of adhesives —
Part 3:
Use of alternative species for bond tests
1 Scope
This Technical Report describes the procedures necessary for the recognition of new wood species by
ISO 20152-1 and ISO 20152-2 for the evaluation of structural wood adhesives.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 20152-1:2010, Timber structures — Bond performance of adhesives — Part 1: Basic requirements
ISO 20152-2, Timber structures — Bond performance of adhesives — Part 2: Additional requirements
3 Test protocols
ISO 20152-1 permits adhesives to be evaluated under what are described as Method A and Method B
procedures. ISO 20152-2 does not make this distinction but the alternative species introduced may also
be used when applying its procedures.
3.1 Using Method A
The provisions contained in this Technical Report apply only to Method A as defined in ISO 20152-1.
3.2 Using Method B
When using Method B procedures, beech is the only substrate permitted. No provisions are available
that permit new species to be introduced into the Method B procedures in ISO 20152-1.
4 Requirements
4.1 Selection of wood species
The proposing body should identify one only of each of the most commonly used softwood and hardwood
species used by their local timber industry for adhesively bonded engineered wood products and
produce evidence that this is the case. The species will not necessarily be the most difficult to adhesively
© ISO 2013 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO/TR 20152-3:2013(E)

bond since other qualification procedures are specified in product standards that require further trials
intended to establish that unusual species can be effectively adhesive
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 23478:2022(Main)
Bamboo structures — Engineered bamboo products — Test methods for determination of physical and mechanical properties

This document specifies test methods suitable for determining the following mechanical properties of engineered bamboo products: a) modulus of elasticity in bending; b) shear modulus; c) bending strength; d) modulus of elasticity in tension parallel to the fibre; e) tension strength parallel to the fibre; f) modulus of elasticity in compression parallel to the fibre; g) compression strength parallel to the fibre; h) modulus of elasticity in tension perpendicular to the fibre; i) tension strength perpendicular to the fibre; j) modulus of elasticity in compression perpendicular to the fibre; k) compression strength perpendicular to the fibre and shear strength; i) shear strength parallel to the fibre. In addition, the determination of dimensions, moisture content and density are specified. This document is applicable to prismatic shapes of glued laminated bamboo and bamboo scrimber intended to resist flexure, shear, axial loads, or combinations thereof.

  • Standard
    28 pages
    English language
    sale 15% off
ISO
ISO/TR 21141:2022(Main)
Timber structures — Timber connections and assemblies — Determination of yield and ultimate characteristics and ductility from test data

The purpose of this document is to extract the methods for determining the yield and ultimate characteristics and ductility of joints and assemblies from test data by reviewing existing standards in Europe, North America and Far East Asia and to provide the basic data for unifying the evaluation methods of parameters by clarifying their similarities and differences. These parameters are applied for determining the seismic performance of timber structures. This document deals with the method for determining the mechanical properties of individual joints and assemblies, and it does not refer to the seismic performance of the entire structure.

  • Technical report
    38 pages
    English language
    sale 15% off
ISO
ISO 22156:2021(Main)
Bamboo structures — Bamboo culms — Structural design

This document applies to the design of bamboo structures whose primary load bearing structure is made of round bamboo or shear panel systems in which the framing members are made from round bamboo. Except as indicated in Clause 12, this document applies to one- and two-storey residential, small commercial or institutional and light industrial buildings not exceeding 7 m in height. This document is concerned only with requirements for mechanical resistance, serviceability and durability of bamboo structures. This document permits an allowable load-bearing capacity design (ACD) and/or allowable stress design (ASD) approach for the design of bamboo structures. Allowable load-bearing capacity and allowable stress approaches may be used in combination in the same structure. This document additionally recognises design approaches based on partial safety factor design (PSFD) and/or load and resistance factor design (LRFD) methods (5.11.1), previous established experience (5.11.2), or documented ‘design by testing’ approaches (5.11.3). Other requirements, such as those concerning thermal or sound insulation, are not considered. Bamboo structures may require consideration of additional requirements beyond the scope of this document. Execution is covered to the extent that it impacts the quality of construction materials and products required to comply with the design requirements contained herein. This document provides a number of modification factors, designated Ci. These are empirically derived factors, based on best available engineering judgement, that are believed to be universally applicable to bamboo materials that are appropriate for building construction. Parameters affecting bamboo material performance are many and are addressed explicitly through the use of experimentally determined characteristic values of strength and stiffness. Annex A provides a summary of the bases upon which the provisions of this document were developed. This document does not apply to — structures made of engineered bamboo products such as glue-laminated bamboo, cross-laminated bamboo, oriented strand, or densified bamboo materials, — bamboo-reinforced materials where bamboo is not the primary load-bearing constituent. This includes bamboo-reinforced concrete, masonry and soil, or, — scaffold structures constructed with bamboo.

  • Standard
    48 pages
    English language
    sale 15% off
  • Draft
    48 pages
    English language
    sale 15% off
ISO
ISO 19993:2020(Main)
Timber structures — Glued laminated timber — Face and edge joint cleavage test

This document specifies methods of evaluating the effectiveness of glued laminated timber face and edge bonds within a manufacturing plant by cleaving of the glue line in both dry and wet conditions. It is not intended that it be used for initial type testing where cyclic delamination or block shear is preferred. It is based on the principle that, provided minimum wood failure percentages are met, then the bond strength exceeds the perpendicular to the grain tension strength of the under-lying substrate and therefore the bond is not the weak element limiting the integrity of a glulam assembly.

  • Standard
    5 pages
    English language
    sale 15% off
ISO
ISO 22389-2:2020(Main)
Timber structures — Bending applications of I-beams — Part 2: Component performance and manufacturing requirements

This document specifies the component performance and manufacturing requirements for prefabricated wood-based I-beams used as structural members in bending applications. It does not cover fire performance, formaldehyde requirements and biological durability. This document gives requirements for manufacturing, in-house quality assurance and periodic re-evaluation of prefabricated wood-based I-beams. Wood-based I-beams tested according to this document are intended for use in covered conditions and utilizing components that are able to resist the effects of moisture on structural performance due to construction delays or other conditions of similar severity, but not permanently exposed to the weather. NOTE The service conditions are similar to "Service class 2" as defined in ISO 20152‑1. Testing, evaluation and performance characterization requirements for prefabricated wood-based I-beams are covered in ISO 22389‑1. This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this document to establish appropriate health and safety practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off
ISO
ISO 22390:2020(Main)
Timber structures — Laminated veneer lumber — Structural properties

This document specifies requirements for establishing the characteristic properties of structural laminated veneer lumber (LVL), including 5th percentile strength values, stiffness characteristics and other performance characteristics, related to its end use as a structural product for dry use (service class 1). It is applicable to members used in flatwise or edgewise bending orientations. It does not cover the assessment of formaldehyde requirements, biological durability, fire performance or manufacturing, such as quality control and marking.

  • Standard
    9 pages
    English language
    sale 15% off
ISO
ISO 8970:2020(Main)
Timber structures — Testing of joints made with mechanical fasteners — Requirements for timber density

This document specifies a method based on density, for the selection of pieces of wood used in determining the strength and stiffness properties of joints between members of structural timber made with mechanical fasteners. It is intended to be used in conjunction with a test standard specifying a test method. It is assumed that the wood pieces are conditioned to the relevant conditions, that the wood density is normally distributed and that any deviations are reported. This document is applicable only to specimens of structural timber. NOTE It is emphasized that the wood density is only one of the properties that can influence the strength of a joint. Other relevant properties are, for example, growth-ring size and orientation, toughness and hardness.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off
ISO
ISO/TR 19623:2019(Main)
Timber structures — Glued laminated timber — Assignment of glued laminated timber characteristic values from laminate properties

This document reviews the methodologies or analytical models that have been used to develop the strength and stiffness of structural glued laminated timber (glulam) from the characteristic properties of lumber laminations. The review is limited to the methodologies used in Europe, the USA, Australia/New Zealand, and Canada as they represent different fundamental philosophies in these areas. As a result, the methodologies are not intended to be combined unless there is clear understanding of the fundamental assumptions adopted by the respective methodologies. NOTE Detailed assumptions used by the respective methodologies are available from the standards listed in the Bibliography.

  • Technical report
    33 pages
    English language
    sale 15% off
ISO
ISO 16696-1:2019(Main)
Timber structures — Cross laminated timber — Part 1: Component performance, production requirements and certification scheme

This document establishes the basic principles for component performance and minimum production requirements for cross laminated timber (CLT). This document also contains scheme requirements for conformance, as provided in Annex D. The document is applicable to CLT products which are manufactured from solid-sawn timber or wood based panels built up of at least three layers in which the grain of adjoining layers are at right angles to each other. This document provides CLT dimension tolerances; component requirements; performance criteria; production, testing and trade marking guidance; and minimum requirements for factory production control. This document is based on known species, species combination and/or wood based panel structural performance and bondability. CLT qualified in accordance with the provisions of this document are intended to resist the effects of moisture on structural performance as can occur due to construction delays or other conditions of similar severity. NOTE This document does not include how CLT is to be used and installed, as it will be detailed in ISO 16696-2.

  • Standard
    25 pages
    English language
    sale 15% off
ISO
ISO 12122-5:2018(Main)
Timber structures — Determination of characteristic values — Part 5: Mechanical connections

This document gives methods of determination of characteristic values for a defined population of mechanical connections between timber components, calculated from full scale test values. It presents methods for the determination of: a) slip modulus of mechanical connections; b) characteristic strength of connections subjected to either monotonic or cyclic loads. Glued connections are excluded from the scope of this document. NOTE 1 It is assumed that the failure mode is the same for all specimens in the sample. NOTE 2 When a small number of test results is available, ISO 12122‑6 is used for the determination of the mean and the 5th percentile values. NOTE 3 Informative commentary to the clauses of this document can be found in Annex A.

  • Standard
    13 pages
    English language
    sale 15% off