ISO 6336-1:1996/Cor 1:1998
(Corrigendum)Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors — Technical Corrigendum 1
Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors — Technical Corrigendum 1
Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale — Partie 1: Principes de base, introduction et facteurs généraux d'influence — Rectificatif technique 1
Izračun nosilnosti ravnozobih in poševnozobih zobnikov - 1. del: Osnove, uvajanje in koeficienti - Tehnični popravek 1
General Information
Relations
Standards Content (Sample)
INTERNATIONAL STANDARD ISO 6336-1:1996
TECHNICAL CORRIGENDUM 1
A
Published 1998-10-15
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • �¯˘˜�˝�—˛˜˝�� ˛—ˆ�˝¨˙��¨� ˇ˛ ���˝˜�—�¨˙��¨¨ • ORGANISATION INTERNATIONALE DE NORMALISATION
Calculation of load capacity of spur and helical gears —
Part 1:
Basic principles, introduction and general influence factors
TECHNICAL CORRIGENDUM 1
Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale —
Partie 1: Principes de base, introduction et facteurs généraux d'influence
RECTIFICATIF TECHNIQUE 1
Technical Corrigendum 1 to International Standard ISO 6336-1:1996 was prepared by Technical Committee
ISO/TC 60, Gears, Subcommittee SC 2, Gear capacity calculation.
Page 48, subclause 7.6.1
In list item a), amend the first sentence to read as follows:
"., positioned symmetrically between bearings (s/l £ 0,1, see figure 16)."
Page 49, footnote 9)
Amend the first sentence to read as follows:
"., i.e. gap width small compared to the facewidth [(B – 2b ) £ 0,5b ]."
B B
ICS 21.200 Ref. No. ISO 6336-1:1996/Cor.1:1998(E
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors -
TECHNICAL CORRIGENDUM 121.200GonilaGearsICS:Ta slovenski standard je istoveten z:ISO 6336-1:1996/Cor 1:1998SIST ISO 6336-1:2002/TC 1:2002en01-julij-2002SIST ISO 6336-1:2002/TC 1:2002SLOVENSKI
STANDARD
SIST ISO 6336-1:2002/TC 1:2002
ICS
21.200Ref. No. ISO 6336-1:1996/Cor.1:1998(E)Descriptors:
gears, cylindrical gears, spur gears, helical gears, load capacity, rules of calculation, generalities.©
ISO 1998Printed in SwitzerlandAINTERNATIONAL STANDARD ISO 6336-1:1996TECHNICAL CORRIGENDUM 1Published 1998-10-15INTERNATIONAL ORGANIZATION FOR STANDARDIZATION · ÌÅÆÄÓÍÀÐÎÄÍÀß ÎÐÃÀÍÈÇÀÖÈß ÏÎ ÑÒÀÍÄÀÐÒÈÇÀÖÈÈ · ORGANISATION INTERNATIONALE DE NORMALISATIONCalculation of load capacity of spur and helical gears —Part 1:Basic principles, introduction and general influence factorsTECHNICAL CORRIGENDUM 1Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale —Partie 1: Principes de base, introduction et facteurs généraux d'influenceRECTIFICATIF TECHNIQUE 1Technical Corrigendum 1 to I
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.