ISO 6336-1:1996/Cor 1:1998

Calculation of load capacity of spur and helical gears - Part 1: Basic principles, introduction and general influence factors - Technical Corrigendum 1

Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale — Partie 1: Principes de base, introduction et facteurs généraux d'influence — Rectificatif technique 1

Izračun nosilnosti ravnozobih in poševnozobih zobnikov - 1. del: Osnove, uvajanje in koeficienti - Tehnični popravek 1

General Information

• Status: Withdrawn
• Publication Date: 14-Oct-1998
• Withdrawal Date: 14-Oct-1998
• ICS: 21.200 - Gears
• Technical Committee: ISO/TC 60/SC 2 - Gear capacity calculation
• Drafting Committee: ISO/TC 60/SC 2/WG 6 - Gear calculations
• Current Stage: 9599 - Withdrawal of International Standard
• Start Date: 04-Sep-2006
• Completion Date: 13-Dec-2025
• Ref Project: SIST ISO 6336-1:2002/TC 1:2002 - Calculation of load capacity of spur and helical gears - Part 1: Basic principles, introduction and general influence factors - TECHNICAL CORRIGENDUM 1

Relations

• Child: ISO 15708-1:2017 - Non-destructive testing - Radiation methods for computed tomography - Part 1: Terminology
• Effective Date: 06-Jun-2022
• Corrects: ISO 6336-1:1996 - Calculation of load capacity of spur and helical gears - Part 1: Basic principles, introduction and general influence factors
• Effective Date: 06-Jun-2022
• Revised: ISO 6336-1:2006 - Calculation of load capacity of spur and helical gears - Part 1: Basic principles, introduction and general influence factors
• Effective Date: 15-Apr-2008
• Child: SIST ISO 6336-1:2002 - Calculation of load capacity of spur and helical gears -- Part 1: Basic principles, introduction and general influence factors
• Effective Date: 12-May-2008
• Child: ISO 6336-1:1996 - Calculation of load capacity of spur and helical gears - Part 1: Basic principles, introduction and general influence factors
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL STANDARD ISO 6336-1:1996
TECHNICAL CORRIGENDUM 1
A
Published 1998-10-15
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • �¯˘˜�˝�—˛˜˝�� ˛—ˆ�˝¨˙��¨� ˇ˛ ���˝˜�—�¨˙��¨¨ • ORGANISATION INTERNATIONALE DE NORMALISATION
Calculation of load capacity of spur and helical gears —
Part 1:
Basic principles, introduction and general influence factors
TECHNICAL CORRIGENDUM 1
Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale —
Partie 1: Principes de base, introduction et facteurs généraux d'influence
RECTIFICATIF TECHNIQUE 1
Technical Corrigendum 1 to International Standard ISO 6336-1:1996 was prepared by Technical Committee
ISO/TC 60, Gears, Subcommittee SC 2, Gear capacity calculation.

Page 48, subclause 7.6.1
In list item a), amend the first sentence to read as follows:
"., positioned symmetrically between bearings (s/l £ 0,1, see figure 16)."
Page 49, footnote 9)
Amend the first sentence to read as follows:
"., i.e. gap width small compared to the facewidth [(B – 2b ) £ 0,5b ]."
B B
ICS 21.200 Ref. No. ISO 6336-1:1996/Cor.1:1998(E
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors -
TECHNICAL CORRIGENDUM 121.200GonilaGearsICS:Ta slovenski standard je istoveten z:ISO 6336-1:1996/Cor 1:1998SIST ISO 6336-1:2002/TC 1:2002en01-julij-2002SIST ISO 6336-1:2002/TC 1:2002SLOVENSKI
STANDARD
ICS
21.200Ref. No. ISO 6336-1:1996/Cor.1:1998(E)Descriptors:
gears, cylindrical gears, spur gears, helical gears, load capacity, rules of calculation, generalities.©
ISO 1998Printed in SwitzerlandAINTERNATIONAL STANDARD ISO 6336-1:1996TECHNICAL CORRIGENDUM 1Published 1998-10-15INTERNATIONAL ORGANIZATION FOR STANDARDIZATION · ÌÅÆÄÓÍÀÐÎÄÍÀß ÎÐÃÀÍÈÇÀÖÈß ÏÎ ÑÒÀÍÄÀÐÒÈÇÀÖÈÈ · ORGANISATION INTERNATIONALE DE NORMALISATIONCalculation of load capacity of spur and helical gears —Part 1:Basic principles, introduction and general influence factorsTECHNICAL CORRIGENDUM 1Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale —Partie 1: Principes de base, introduction et facteurs généraux d'influenceRECTIFICATIF TECHNIQUE 1Technical Corrigendum 1 to I
...