SIST EN 60512-9-3:2006

Connectors for electronic equipment - Tests and measurements -- Part 9-3: Endurance tests - Test 9c: Mechanical operation (engaging/separating) with electrical load

This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. They may also be used for similar devices when specified in a detail specification. The object of this test is to detail a standard test method to assess the mechanical and electrical operational endurance of electromechanical components in the normal operating mode with a specified electrical load. This test method is applicable for connectors used in the Safe Extra Low Voltage (SELV) range only as defined in IEC 61140 (3.26). Connectors that are used outside the SELV range are considered in IEC 61984.

Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren -- Teil 9-3: Dauerprüfungen - Prüfung 9c: Mechanische Lebensdauer (Stecken/Ziehen) mit elektrischer Belastung

Connecteurs pour équipements électroniques - Essais et mesures -- Partie 9-3: Essais d'endurance - Essai 9c: manoeuvres mécaniques (d'accouplement et de désaccouplement) avec charge électrique

Précise une méthode d'essai normalisée pour évaluer l'endurance fonctionnelle mécanique et électrique des composants électromécaniques en mode de fonctionnement normal avec une charge électrique spécifiée.

Konektorji za elektronsko opremo – Preskusi in meritve – 9-3. del: Preskusi vzdržljivosti – Preskus 9c: Mehansko (stikanje/raztikanje) z električno bremenitvijo (IEC 60512-9-3:2006)

General Information

• Status: Withdrawn
• Publication Date: 30-Jun-2006
• Withdrawal Date: 10-Jun-2014
• ICS: 31.220.10 - Plug-and-socket devices. Connectors
• Technical Committee: SS EIT - Technical Board for the electrotechnical, information technology and telecommunications fields
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 11-Jun-2014
• Due Date: 04-Jul-2014
• Completion Date: 11-Jun-2014
• Ref Project: EN 60512-9-3:2006 - Connectors for electronic equipment - Tests and measurements - Part 9-3: Endurance tests - Test 9c: Mechanical operation (engaging/separating) with electrical load

Relations

• Revised: SIST EN 60512-9-3:2011 - Connectors for electronic equipment - Tests and measurements - Part 9-3: Endurance tests - Test 9c: Mechanical operation (mating and un-mating) with electrical load
• Effective Date: 06-May-2014
• Revised: SIST EN 60512-9-3:2011 - Connectors for electronic equipment - Tests and measurements - Part 9-3: Endurance tests - Test 9c: Mechanical operation (mating and un-mating) with electrical load
• Effective Date: 14-May-2010
• Replaced By: SIST EN 60512-9-3:2011 - Connectors for electronic equipment - Tests and measurements - Part 9-3: Endurance tests - Test 9c: Mechanical operation (mating and un-mating) with electrical load
• Effective Date: 28-Jan-2023

Standards Content (Sample)

SIST EN 60512-9-3:2006SLOVENSKIjulij 2006
STANDARDKonektorji za elektronsko opremo – Preskusi in meritve – 9-3. del: Preskusi vzdržljivosti – Preskus 9c: Mehansko (stikanje/raztikanje) z električno bremenitvijo (IEC 60512-9-3:2006)Connectors for electronic equipment - Tests and measurements - Part 9-3: Endurance tests – Test 9c: Mechanical operation (engaging/separating) with electrical load (IEC 60512-9-3:2006)©
Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljenoReferenčna številkaSIST EN 60512-9-3:2006(en)ICS31.220.10







EUROPEAN STANDARD EN 60512-9-3 NORME EUROPÉENNE
EUROPÄISCHE NORM March 2006
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2006 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60512-9-3:2006 E
ICS 31.220.10
English version
Connectors for electronic equipment -
Tests and measurements Part 9-3: Endurance tests -
Test 9c: Mechanical operation (engaging/separating)
with electrical load (IEC 60512-9-3:2006)
Connecteurs pour équipements électroniques -
Essais et mesures Partie 9-3: Essais d'endurance -
Essai 9c: Manoeuvres mécaniques (d'accouplement et de désaccouplement) avec charge électrique (CEI 60512-9-3:2006)
Steckverbinder für elektronische Einrichtungen -
Mess- und Prüfverfahren Teil 9-3: Dauerprüfungen -
Prüfung 9c: Mechanische Lebensdauer (Stecken/Ziehen)
mit elektrischer Belastung (IEC 60512-9-3:2006)
This European Standard was approved by CENELEC on 2006-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.



EN 60512-9-3:2006
- 2 -
Foreword The text of document 48B/1576/FDIS, future edition 1 of IEC 60512-9-3, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-9-3 on 2006-03-01. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100 which explains the structure of the EN 60512 series.
The following dates were fixed: – latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop) 2006-12-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow) 2009-03-01 This European Standard makes reference to International Standards. Where the International Standard referred to has been endorsed as a European Standard or a home-grown European Standard exists, this European Standard shall be applied instead. Pertinent information can be found on the CENELEC web site. __________ Endorsement notice The text of the International Standard IEC 60512-9-3:2006 was approved by CENELEC as a European Standard without any modification. __________



NORME INTERNATIONALECEIIEC INTERNATIONAL STANDARD 60512-9-3Première éditionFirst edition2006-02 Connecteurs pour équipements électroniques – Essais et mesures – Partie 9-3: Essais d'endurance – Essai 9c: Manoeuvres mécaniques (d'accouplement et de désaccouplement) avec charge électrique
Connectors for electronic equipment – Tests and measurements – Part 9-3: Endurance tests – Test 9c: Mechanical operation (engaging/separating) with electrical load Pour prix, voir catalogue en vigueur For price, see current catalogue IEC 2006
Droits de reproduction réservés

Copyright - all rights reserved Aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l'éditeur. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission,
3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: [phone] Telefax: [phone] E-mail: [e-mail]
Web: www.iec.ch CODE PRIX PRICE CODE K Commission Electrotechnique InternationaleInternational Electrotechnical Commission



60512-9-3  IEC:2006 – 3 – CONTENTS FOREWORD.5
1 Scope and object.9 2 Normative references.9 3 Preparations.11 3.1 Preparation of specimen.11 3.2 Mounting.11 4 Method.11 4.1 General.11 4.2 Measurements and requirements.11 4.3 Resistive load, a.c. or d.c. voltage.13 4.4 Lamp load, a.c. or d.c. voltage.13 4.5 Inductive load.13 4.6 Capacitive load.15 4.7 RLC load – d.c.15 5 Details to be specified.15
Annex A (informative)
RLC Load circuit diagram.17
Figure A.1 – RLC load circuit diagram.17



60512-9-3  IEC:2006 – 5 – INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
CONNECTORS FOR ELECTRONIC EQUIPMENT – TESTS AND MEASUREMENTS –
Part 9-3: Endurance tests –
Test 9c: Mechanical operation
(engaging/separating) with electrical load
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury
...