SIST EN 303 204-1 V1.1.1:2014
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Network Based Short Range Devices (SRD) - Radio equipment to be used in the 870 MHz to 876 MHz frequency range with power levels ranging up to 500 mW - Part 1: Technical characteristics and test methods
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Network Based Short Range Devices (SRD) - Radio equipment to be used in the 870 MHz to 876 MHz frequency range with power levels ranging up to 500 mW - Part 1: Technical characteristics and test methods
To produce a Harmonised Standard, taking into account the ongoing ECC Report 200 and ECC Report 189, to support Network Based SRDs within the 870 -876 MHz frequency range, such as Metropolitan Machine Mesh (M3M e.g. TR 103 055) and Smart Metering/Smart Grid (e.g. TR 102 886) - TS 102 887 could also of relevance. It is noted that these SRD equipment will be class 2 to ensure the best spectrum efficiency whilst protecting the primary service operating in some countries.
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Omrežne naprave kratkega dosega (SRD) - Radijska oprema, ki se uporablja v frekvenčnem območju od 870 MHz do 876 MHz z močnostnimi nivoji do največ 500 mW - 1. del: Tehnične karakteristike in preskusne metode
Za izdelavo harmoniziranega standarda je lahko pomembno tudi upoštevanje tekočega poročila 200 in poročila 189 Odbora za elektronske komunikacije za podporo omrežnih naprav kratkega dosega v frekvenčnem območju 870, –876 MHz, npr. Metropolitan Machine Mesh (M3M, npr. TR 103 055) in Smart Metering/Smart Grid (npr. TR 102 886) – TS 102 887. Upoštevano je, da bo ta oprema naprav kratkega dosega razreda 2, da se zagotovi najboljša učinkovitost spektra med zaščito osnovne storitve, ki deluje v nekaterih državah.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Network Based Short Range Devices (SRD) - Radio equipment to be used in the 870 MHz to 876 MHz frequency range with power levels ranging up to 500 mW - Part 1: Technical characteristics and test methods33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:EN 303 204-1 Version 1.1.1SIST EN 303 204-1 V1.1.1:2014en01-december-2014SIST EN 303 204-1 V1.1.1:2014SLOVENSKI
STANDARD
SIST EN 303 204-1 V1.1.1:2014
ETSI EN 303 204-1 V1.1.1 (2014-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Network Based Short Range Devices (SRD); Radio equipment to be used in the 870 MHz to 876 MHz frequency range with power levels ranging up to 500 mW; Part 1:Technical characteristics and test methods
EUROPEAN STANDARD SIST EN 303 204-1 V1.1.1:2014
ETSI ETSI EN 303 204-1 V1.1.1 (2014-10) 2
Reference DEN/ERM-TG28-503 Keywords radio, SRD ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 303 204-1 V1.1.1:2014
ETSI ETSI EN 303 204-1 V1.1.1 (2014-10) 3 Contents Intellectual Property Rights . 8 Foreword . 8 Modal verbs terminology . 8 Introduction . 8 1 Scope . 11 2 References . 11 2.1 Normative references . 11 2.2 Informative references . 12 3 Definitions, symbols and abbreviations . 12 3.1 Definitions . 12 3.2 Symbols . 14 3.3 Abbreviations . 15 4 Technical requirements specifications . 15 4.1 General performance criteria . 15 4.2 Presentation of equipment for testing purposes . 16 4.2.1 Choice of model for testing . 16 4.2.1.1 EUT with an external RF connector . 16 4.2.1.2 EUT without an external RF connector . 16 4.2.1.2.1 EUT with an internal connector . 16 4.2.1.2.2 EUT with a temporary antenna connector . 16 4.2.1.2.3 Use of a Test Fixture . 17 4.2.2 Testing of modular equipment . 17 4.2.3 Transmitter shut-off facility . 17 4.2.4 Receiver mute or squelch or battery saving circuit . 17 4.2.5 Marking (equipment identification) . 17 4.3 Auxiliary test equipment . 17 4.4 Provider declared information . 17 5 Test conditions, power sources and ambient temperatures . 18 5.1 Normal and extreme test conditions . 18 5.2 Test power source . 18 5.2.1 External test power source . 19 5.2.2 Internal test power source . 19 5.3 Normal test conditions . 19 5.3.1 Normal temperature and humidity . 19 5.3.2 Normal test power source . 19 5.3.2.1 Mains voltage . 19 5.3.2.2 Regulated lead-acid battery power sources . 19 5.3.2.3 Other power sources . 20 5.4 Extreme test conditions . 20 5.4.1 Extreme temperatures . 20 5.4.1.1 Procedure for tests at extreme temperatures . 20 5.4.1.1.1 Procedure for equipment designed for continuous operation . 20 5.4.1.1.2 Procedure for equipment designed for intermittent operation . 20 5.4.1.2 Extreme temperature ranges . 21 5.4.2 Extreme test source voltages . 21 5.4.2.1 Mains voltage . 21 5.4.2.2 Regulated lead-acid battery power sources . 21 5.4.2.3 Power sources using other types of batteries . 21 5.4.2.4 Other power sources . 21 6 General test conditions . 22 6.1 Transmitter test signals . 22 SIST EN 303 204-1 V1.1.1:2014
ETSI ETSI EN 303 204-1 V1.1.1 (2014-10) 4 6.2 Conducted measurements . 22 6.2.1 Artificial antenna . 22 6.2.2 Voltage Standing Wave Ratio (VSWR) . 23 6.3 Radiated measurements . 23 6.4 Applicable measurement methods . 23 6.5 Modes of operation . 24 6.5.1 Test mode. 24 6.5.2 Transmitter operation . 24 6.5.3 Testing of multi-frequency or channel agile equipment . 25 6.5.4 Non-uniform maximum transmit power . 25 6.6 Measuring receiver . 25 6.6.1 Reference Bandwidth . 26 6.7 Test equipment . 26 7 Methods of measurement and limits for transmitter parameters . 27 7.1 General limits . 27 7.2 Frequency error . 27 7.2.1 Description . 27 7.2.2 Test method . 27 7.2.2.1 Test conditions . 27 7.2.2.2 Radiated measurement . 27 7.2.2.3 Conducted measurement . 28 7.2.2.4 Alternate conducted measurement . 28 7.2.2.5 Measurement procedure . 28 7.2.3 Limits . 28 7.3 Average power (conducted) . 29 7.3.1 Description . 29 7.3.2 Test method . 29 7.3.2.1 Test conditions . 29 7.3.2.2 Measurement Procedure . 29 7.3.3 Limits . 30 7.4 Effective radiated power . 30 7.4.1 Description . 30 7.4.2 Test method . 30 7.4.2.1 Test conditions . 30 7.4.2.2 Measurement procedure . 30 7.4.3 Limits . 31 7.5 Transient power . 31 7.5.1 Description . 31 7.5.2 Test method . 31 7.5.2.1 Test conditions . 31 7.5.2.2 Radiated measurement . 32 7.5.2.3 Conducted measurement . 32 7.5.2.4 Measurement procedure . 32 7.5.3 Limits . 33 7.6 Occupied bandwidth . 34 7.6.1 Description . 34 7.6.2 Test method . 34 7.6.2.1 Test conditions . 34 7.6.2.2 Radiated measurement . 34 7.6.2.3 Conducted measurement . 34 7.6.2.4 Alternate conducted measurement . 34 7.6.2.5 Measurement procedure . 35 7.6.3 Limits . 36 7.7 Unwanted emissions in the out-of-band domain . 36 7.7.1 Description . 36 7.7.2 Test method . 37 7.7.2.1 Test conditions . 37 7.7.2.2 Radiated measurement . 37 7.7.2.3 Conducted measurement . 37 7.7.2.4 Measurement procedure . 38 7.7.3 Limits . 39 SIST EN 303 204-1 V1.1.1:2014
ETSI ETSI EN 303 204-1 V1.1.1 (2014-10) 5 7.8 Unwanted emissions in the spurious domain. 40 7.8.1 Description . 40 7.8.2 Test method . 40 7.8.2.1 Test conditions . 40 7.8.2.2 Radiated measurement . 40 7.8.2.3 Radiated measurement . 41 7.8.2.4 Conducted measurement . 41 7.8.2.5 Measurement procedure . 41 7.8.2.5.1 Conducted measurement. 41 7.8.2.5.2 Radiated measurement . 42 7.8.3 Limits . 43 7.9 Frequency stability under low voltage conditions . 43 7.9.1 Description . 43 7.9.2 Test method . 43 7.9.2.1 Test conditions . 43 7.9.2.2 Radiated measurement . 43 7.9.2.3 Conducted measurement . 44 7.9.2.4 Alternate conducted measurement . 44 7.9.2.5 Measurement procedure . 44 7.9.3 Limits . 45 7.10 Duty cycle . 45 7.10.1 Description . 45 7.10.2 Duty cycle . 45 7.10.2.1 Test method . 45 7.10.2.2 Measurement procedure . 45 7.10.3 Short term behaviour . 45 7.10.3.1 Test method . 45 7.10.3.2 Test conditions . 46 7.10.3.3 Radiated measurement . 46 7.10.3.4 Conducted measurement . 46 7.10.3.5 Alternate conducted measurement . 46 7.10.3.6 Measurement procedure . 46 7.10.4 Limits . 47 7.11 Automatic / adaptive power control . 47 7.11.1 Description . 47 7.11.2 Test method . 47 7.11.2.1 Test conditions . 48 7.11.2.2 Radiated measurement . 48 7.11.2.3 Conducted measurement . 48 7.11.2.4 Measurement procedure . 48 7.11.3 Limits . 49 8 Methods of measurement and limits for receiver parameters . 49 8.1 General limits . 49 8.2 Receiver sensitivity . 50 8.2.1 Description . 50 8.2.2 Test method . 50 8.2.2.1 Test Conditions . 50 8.2.2.2 Radiated measurement . 50 8.2.2.3 Conducted measurement . 50 8.2.2.4 Measurement procedure . 50 8.2.3 Limits . 51 8.3 Clear channel assessment threshold . 51 8.3.1 Description . 51 8.3.2 Test method . 51 8.3.2.1 Test conditions . 52 8.3.2.2 Radiated measurement .
...
ETSI EN 303 204-1 V1.1.1 (2014-10)
EUROPEAN STANDARD
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Network Based Short Range Devices (SRD);
Radio equipment to be used in the 870 MHz to 876 MHz
frequency range with power levels ranging up to 500 mW;
Part 1:Technical characteristics and test methods
---------------------- Page: 1 ----------------------
2 ETSI EN 303 204-1 V1.1.1 (2014-10)
Reference
DEN/ERM-TG28-503
Keywords
radio, SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 204-1 V1.1.1 (2014-10)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 11
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 12
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 14
3.3 Abbreviations . 15
4 Technical requirements specifications . 15
4.1 General performance criteria . 15
4.2 Presentation of equipment for testing purposes . 16
4.2.1 Choice of model for testing . 16
4.2.1.1 EUT with an external RF connector . 16
4.2.1.2 EUT without an external RF connector . 16
4.2.1.2.1 EUT with an internal connector . 16
4.2.1.2.2 EUT with a temporary antenna connector . 16
4.2.1.2.3 Use of a Test Fixture . 17
4.2.2 Testing of modular equipment . 17
4.2.3 Transmitter shut-off facility . 17
4.2.4 Receiver mute or squelch or battery saving circuit . 17
4.2.5 Marking (equipment identification) . 17
4.3 Auxiliary test equipment . 17
4.4 Provider declared information . 17
5 Test conditions, power sources and ambient temperatures . 18
5.1 Normal and extreme test conditions . 18
5.2 Test power source . 18
5.2.1 External test power source . 19
5.2.2 Internal test power source . 19
5.3 Normal test conditions . 19
5.3.1 Normal temperature and humidity . 19
5.3.2 Normal test power source . 19
5.3.2.1 Mains voltage . 19
5.3.2.2 Regulated lead-acid battery power sources . 19
5.3.2.3 Other power sources . 20
5.4 Extreme test conditions . 20
5.4.1 Extreme temperatures . 20
5.4.1.1 Procedure for tests at extreme temperatures . 20
5.4.1.1.1 Procedure for equipment designed for continuous operation . 20
5.4.1.1.2 Procedure for equipment designed for intermittent operation . 20
5.4.1.2 Extreme temperature ranges . 21
5.4.2 Extreme test source voltages . 21
5.4.2.1 Mains voltage . 21
5.4.2.2 Regulated lead-acid battery power sources . 21
5.4.2.3 Power sources using other types of batteries . 21
5.4.2.4 Other power sources . 21
6 General test conditions . 22
6.1 Transmitter test signals . 22
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 204-1 V1.1.1 (2014-10)
6.2 Conducted measurements . 22
6.2.1 Artificial antenna . 22
6.2.2 Voltage Standing Wave Ratio (VSWR) . 23
6.3 Radiated measurements . 23
6.4 Applicable measurement methods . 23
6.5 Modes of operation . 24
6.5.1 Test mode. 24
6.5.2 Transmitter operation . 24
6.5.3 Testing of multi-frequency or channel agile equipment . 25
6.5.4 Non-uniform maximum transmit power . 25
6.6 Measuring receiver . 25
6.6.1 Reference Bandwidth . 26
6.7 Test equipment . 26
7 Methods of measurement and limits for transmitter parameters . 27
7.1 General limits . 27
7.2 Frequency error . 27
7.2.1 Description . 27
7.2.2 Test method . 27
7.2.2.1 Test conditions . 27
7.2.2.2 Radiated measurement . 27
7.2.2.3 Conducted measurement . 28
7.2.2.4 Alternate conducted measurement . 28
7.2.2.5 Measurement procedure . 28
7.2.3 Limits . 28
7.3 Average power (conducted) . 29
7.3.1 Description . 29
7.3.2 Test method . 29
7.3.2.1 Test conditions . 29
7.3.2.2 Measurement Procedure . 29
7.3.3 Limits . 30
7.4 Effective radiated power . 30
7.4.1 Description . 30
7.4.2 Test method . 30
7.4.2.1 Test conditions . 30
7.4.2.2 Measurement procedure . 30
7.4.3 Limits . 31
7.5 Transient power . 31
7.5.1 Description . 31
7.5.2 Test method . 31
7.5.2.1 Test conditions . 31
7.5.2.2 Radiated measurement . 32
7.5.2.3 Conducted measurement . 32
7.5.2.4 Measurement procedure . 32
7.5.3 Limits . 33
7.6 Occupied bandwidth . 34
7.6.1 Description . 34
7.6.2 Test method . 34
7.6.2.1 Test conditions . 34
7.6.2.2 Radiated measurement . 34
7.6.2.3 Conducted measurement . 34
7.6.2.4 Alternate conducted measurement . 34
7.6.2.5 Measurement procedure . 35
7.6.3 Limits . 36
7.7 Unwanted emissions in the out-of-band domain . 36
7.7.1 Description . 36
7.7.2 Test method . 37
7.7.2.1 Test conditions . 37
7.7.2.2 Radiated measurement . 37
7.7.2.3 Conducted measurement . 37
7.7.2.4 Measurement procedure . 38
7.7.3 Limits . 39
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 204-1 V1.1.1 (2014-10)
7.8 Unwanted emissions in the spurious domain. 40
7.8.1 Description . 40
7.8.2 Test method . 40
7.8.2.1 Test conditions . 40
7.8.2.2 Radiated measurement . 40
7.8.2.3 Radiated measurement . 41
7.8.2.4 Conducted measurement . 41
7.8.2.5 Measurement procedure . 41
7.8.2.5.1 Conducted measurement. 41
7.8.2.5.2 Radiated measurement . 42
7.8.3 Limits . 43
7.9 Frequency stability under low voltage conditions . 43
7.9.1 Description . 43
7.9.2 Test method . 43
7.9.2.1 Test conditions . 43
7.9.2.2 Radiated measurement . 43
7.9.2.3 Conducted measurement . 44
7.9.2.4 Alternate conducted measurement . 44
7.9.2.5 Measurement procedure . 44
7.9.3 Limits . 45
7.10 Duty cycle . 45
7.10.1 Description . 45
7.10.2 Duty cycle . 45
7.10.2.1 Test method . 45
7.10.2.2 Measurement procedure . 45
7.10.3 Short term behaviour . 45
7.10.3.1 Test method . 45
7.10.3.2 Test conditions . 46
7.10.3.3 Radiated measurement . 46
7.10.3.4 Conducted measurement . 46
7.10.3.5 Alternate conducted measurement . 46
7.10.3.6 Measurement procedure . 46
7.10.4 Limits . 47
7.11 Automatic / adaptive power control . 47
7.11.1 Description . 47
7.11.2 Test method . 47
7.11.2.1 Test conditions . 48
7.11.2.2 Radiated measurement . 48
7.11.2.3 Conducted measurement . 48
7.11.2.4 Measurement procedure . 48
7.11.3 Limits . 49
8 Methods of measurement and limits for receiver parameters . 49
8.1 General limits . 49
8.2 Receiver sensitivity . 50
8.2.1 Description . 50
8.2.2 Test method . 50
8.2.2.1 Test Conditions . 50
8.2.2.2 Radiated measurement . 50
8.2.2.3 Conducted measurement . 50
8.2.2.4 Measurement procedure . 50
8.2.3 Limits . 51
8.3 Clear channel assessment threshold . 51
8.3.1 Description . 51
8.3.2 Test method . 51
8.3.2.1 Test conditions . 52
8.3.2.2 Radiated measurement . 52
8.3.2.3 Conducted measurement . 52
8.3.2.4 Measurement procedure . 52
8.3.3 Limits .
...
Draft ETSI EN 303 204-1 V1.1.0 (2014-06)
European Standard
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Network Based Short Range Devices (SRD);
Radio equipment to be used in the 870 MHz to 876 MHz
frequency range with power levels ranging up to 500 mW;
Part 1:Technical characteristics and test methods
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 204-1 V1.1.0 (2014-06)
Reference
DEN/ERM-TG28-503
Keywords
radio, SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 204-1 V1.1.0 (2014-06)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 11
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 12
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 14
3.3 Abbreviations . 15
4 Technical requirements specifications . 15
4.1 General performance criteria . 15
4.2 Presentation of equipment for testing purposes . 16
4.2.1 Choice of model for testing . 16
4.2.1.1 EUT with an external RF connector . 16
4.2.1.2 EUT without an external RF connector . 16
4.2.1.2.1 EUT with an internal connector . 16
4.2.1.2.2 EUT with a temporary antenna connector . 16
4.2.1.2.3 Use of a Test Fixture . 17
4.2.2 Testing of modular equipment . 17
4.2.3 Transmitter shut-off facility . 17
4.2.4 Receiver mute or squelch or battery saving circuit . 17
4.2.5 Marking (equipment identification) . 17
4.3 Auxiliary test equipment . 17
4.4 Provider declared information . 17
5 Test conditions, power sources and ambient temperatures . 18
5.1 Normal and extreme test conditions . 18
5.2 Test power source . 18
5.2.1 External test power source . 19
5.2.2 Internal test power source . 19
5.3 Normal test conditions . 19
5.3.1 Normal temperature and humidity . 19
5.3.2 Normal test power source . 19
5.3.2.1 Mains voltage . 19
5.3.2.2 Regulated lead-acid battery power sources . 19
5.3.2.3 Other power sources . 20
5.4 Extreme test conditions . 20
5.4.1 Extreme temperatures . 20
5.4.1.1 Procedure for tests at extreme temperatures . 20
5.4.1.1.1 Procedure for equipment designed for continuous operation . 20
5.4.1.1.2 Procedure for equipment designed for intermittent operation . 20
5.4.1.2 Extreme temperature ranges . 21
5.4.2 Extreme test source voltages . 21
5.4.2.1 Mains voltage . 21
5.4.2.2 Regulated lead-acid battery power sources . 21
5.4.2.3 Power sources using other types of batteries . 21
5.4.2.4 Other power sources . 21
6 General test conditions . 22
6.1 Transmitter test signals . 22
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 204-1 V1.1.0 (2014-06)
6.2 Conducted measurements . 22
6.2.1 Artificial antenna . 22
6.2.2 Voltage Standing Wave Ratio (VSWR) . 23
6.3 Radiated measurements . 23
6.4 Applicable measurement methods . 23
6.5 Modes of operation . 24
6.5.1 Test mode. 24
6.5.2 Transmitter operation . 24
6.5.3 Testing of multi-frequency or channel agile equipment . 25
6.5.4 Non-uniform maximum transmit power . 25
6.6 Measuring receiver . 25
6.6.1 Reference Bandwidth . 26
6.7 Test equipment . 26
7 Methods of measurement and limits for transmitter parameters . 26
7.1 General limits . 26
7.2 Frequency error . 27
7.2.1 Description . 27
7.2.2 Test method . 27
7.2.2.1 Test conditions . 27
7.2.2.2 Radiated measurement . 27
7.2.2.3 Conducted measurement . 27
7.2.2.4 Alternate conducted measurement . 27
7.2.2.5 Measurement procedure . 28
7.2.3 Limits . 28
7.3 Average power (conducted) . 28
7.3.1 Description . 28
7.3.2 Test method . 29
7.3.2.1 Test conditions . 29
7.3.2.2 Measurement Procedure . 29
7.3.3 Limits . 30
7.4 Effective radiated power . 30
7.4.1 Description . 30
7.4.2 Test method . 30
7.4.2.1 Test conditions . 30
7.4.2.2 Measurement procedure . 30
7.4.3 Limits . 31
7.5 Transient power . 31
7.5.1 Description . 31
7.5.2 Test method . 31
7.5.2.1 Test conditions . 31
7.5.2.2 Radiated measurement . 31
7.5.2.3 Conducted measurement . 31
7.5.2.4 Measurement procedure . 32
7.5.3 Limits . 33
7.6 Occupied bandwidth . 33
7.6.1 Description . 33
7.6.2 Test method . 33
7.6.2.1 Test conditions . 33
7.6.2.2 Radiated measurement . 34
7.6.2.3 Conducted measurement . 34
7.6.2.4 Alternate conducted measurement . 34
7.6.2.5 Measurement procedure . 34
7.6.3 Limits . 35
7.7 Unwanted emissions in the out-of-band domain . 36
7.7.1 Description . 36
7.7.2 Test method . 37
7.7.2.1 Test conditions . 37
7.7.2.2 Radiated measurement . 37
7.7.2.3 Conducted measurement . 37
7.7.2.4 Measurement procedure . 37
7.7.3 Limits . 39
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 204-1 V1.1.0 (2014-06)
7.8 Unwanted emissions in the spurious domain. 39
7.8.1 Description . 39
7.8.2 Test method . 40
7.8.2.1 Test conditions . 40
7.8.2.2 Radiated measurement . 40
7.8.2.3 Radiated measurement . 40
7.8.2.4 Conducted measurement . 40
7.8.2.5 Measurement procedure . 41
7.8.2.5.1 Conducted measurement. 41
7.8.2.5.2 Radiated measurement . 41
7.8.3 Limits . 43
7.9 Frequency stability under low voltage conditions . 43
7.9.1 Description . 43
7.9.2 Test method . 43
7.9.2.1 Test conditions . 43
7.9.2.2 Radiated measurement . 43
7.9.2.3 Conducted measurement . 43
7.9.2.4 Alternate conducted measurement . 43
7.9.2.5 Measurement procedure . 44
7.9.3 Limits . 44
7.10 Duty cycle . 45
7.10.1 Description . 45
7.10.2 Duty cycle . 45
7.10.2.1 Test method . 45
7.10.2.2 Measurement procedure . 45
7.10.3 Short term behaviour . 45
7.10.3.1 Test method . 45
7.10.3.2 Test conditions . 45
7.10.3.3 Radiated measurement . 46
7.10.3.4 Conducted measurement . 46
7.10.3.5 Alternate conducted measurement . 46
7.10.3.6 Measurement procedure . 46
7.10.4 Limits . 47
7.11 Automatic / adaptive power control . 47
7.11.1 Description . 47
7.11.2 Test method . 47
7.11.2.1 Test conditions . 47
7.11.2.2 Radiated measurement . 48
7.11.2.3 Conducted measurement . 48
7.11.2.4 Measurement procedure . 48
7.11.3 Limits . 49
8 Methods of measurement and limits for receiver parameters . 49
8.1 General limits . 49
8.2 Receiver sensitivity . 50
8.2.1 Description . 50
8.2.2 Test method . 50
8.2.2.1 Test Conditions . 50
8.2.2.2 Radiated measurement . 50
8.2.2.3 Conducted measurement . 50
8.2.2.4 Measurement procedure . 50
8.2.3 Limits . 51
8.3 Clear channel assessment threshold . 51
8.3.1 Description . 51
8.3.2 Test method . 51
8.3.2.1 Test conditions . 52
8.3.2.2 Radiated measurement . 52
8.3.2.3 Conducted measurement . 52
8.3.2.4 Measurement procedure . 52
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.