Aerospace series - Tubes - Selection for engines fluid systems

The present standard gives a selection of external diameters and thicknesses of tubes according to ISO 2964.
These tubes shall be used for conveying fluids such as kerosene, oil, air, etc. for engine application.

Luft- und Raumfahrt - Rohre für Fluid-Systeme an Triebwerken - Auswahl

Die vorliegende Norm gibt eine Auswahl an Außendurchmessern und Wanddicken von Rohren nach ISO 2964.
Diese Rohre sind zur Förderung von Flüssigkeiten wie Kerosin, Öl, Luft usw. bei Triebwerken anzuwenden.

Série aérospatiale - Tubes - Sélection pour circuits de fluide pour application moteurs

Aeronavtika - Cevi - Izbira cevi za fluidne sisteme pri motorjih

General Information

Status
Published
Publication Date
22-May-2008
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
09-May-2008
Due Date
14-Jul-2008
Completion Date
23-May-2008

Buy Standard

Standard
EN 3717:2008
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Tubes - Selection for engines fluid systemsAeronavtika - Cevi - Izbira cevi za fluidne sisteme pri motorjihSérie aérospatiale - Tubes - Sélection pour circuits de fluide pour application moteursLuft- und Raumfahrt - Rohre für Fluid-Systeme an Triebwerken - Auswahl49.080Aerospace fluid systems and componentsICS:SIST EN 3717:2008enTa slovenski standard je istoveten z:EN 3717:200801-julij-2008SIST EN 3717:2008SLOVENSKI
STANDARD







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3717April 2008ICS 49.080 English VersionAerospace series - Tubes - Selection for engines fluid systemsSérie aérospatiale - Tubes - Sélection pour circuits defluide pour application moteursLuft- und Raumfahrt - Rohre für Fluid-Systeme anTriebwerken - AuswahlThis European Standard was approved by CEN on 21 December 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3717:2008: E



EN 3717:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Dimensions.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.