SIST EN 1630:2021
(Main)Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance - Test method for the determination of resistance to manual burglary attempts
Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance - Test method for the determination of resistance to manual burglary attempts
This document specifies a test method for the determination of resistance to manual burglary attempts in order to assess the burglar resistant characteristics of pedestrian doorsets, windows, curtain walling, grilles and shutters. It is applicable to the following means of opening: turning, tilting, folding, turn-tilting, top or bottom hung, sliding (horizontally and vertically), pivoted (horizontally and vertically) and rolling as well as fixed constructions.
This document does not directly cover the resistance of locks and cylinders to attack with picking tools. It also does not cover the attack of electric, electronic and electromagnetic operated burglar resistant construction products using attack methods that might defeat these characteristics.
The manufacturer's installation instructions will give guidance on the fixing of the product.
An example for the contents of the manufacturer’s installation instructions is given in Annex A of prEN 1627:2019.
This document does not apply to doors, gates and barriers, intended for installation in areas in the reach of persons, and for which the main intended uses are giving safe access for goods and vehicles accompanied or driven by persons in industrial, commercial or residential premises, as covered by EN 13241.
It is acknowledged that there are two aspects to the burglar resistance performance of construction products, their normal resistance to forced operation and their ability to remain fixed to the building. This test method does not evaluate the performance of the fixing to the building.
Türen, Fenster, Vorhangfassaden, Gitterelemente und Abschlüsse - Einbruchhemmung - Prüfverfahren für die Ermittlung der Widerstandsfähigkeit gegen manuelle Einbruchversuche
Dieses Dokument legt ein Prüfverfahren zur Ermittlung der Widerstandsfähigkeit gegen manuelle Einbruchversuche fest, um die einbruchhemmenden Eigenschaften von Türelementen, Fenstern, Vorhang-fassaden, Gitterelementen und Abschlüssen zu bewerten. Es gilt für die folgenden Öffnungsarten: Drehen, Kippen, Falten, Drehkippen, Schwingen, Schieben (horizontal und vertikal), Schwenken (horizontal und vertikal) und Rollen sowie für nicht öffenbare Konstruktionen.
Dieses Dokument behandelt nicht direkt die Widerstandsfähigkeit von Schlössern und Schließzylindern gegen Angriffe mit Sperrwerkzeugen (Picking). Ebenfalls nicht behandelt wird der Angriff auf elektrisch, elektronisch und elektromagnetisch betätigte einbruchhemmende Bauprodukte mit Hilfe von Angriffs-methoden, die diese Eigenschaften ausschalten könnten.
Leitlinien zur Befestigung des Produkts sind der Einbauanweisung des Herstellers zu entnehmen.
Ein Beispiel für den Inhalt der Montageanweisungen des Herstellers ist in prEN 1627:2019, Anhang A, beschrieben.
Dieses Dokument gilt nicht für Türen, Tore und Schranken, die für den Einbau in Zugangsbereichen von Personen vorgesehen sind und deren hauptsächlich vorgesehene Verwendung darin besteht, eine sichere Zufahrt für Waren und Fahrzeuge, begleitet oder geführt (gesteuert) von Personen, in industriellen, gewerblichen oder Wohnbereichen zu ermöglichen, was in EN 13241 behandelt wird.
Es gibt bekanntermaßen zwei Aspekte der einbruchhemmenden Leistungsfähigkeit von Bauprodukten, ihr üblicher Widerstand gegen gewaltsame Öffnung und ihre Fähigkeit, im Gebäude fest verankert zu bleiben. Das vorliegende Prüfverfahren bewertet nicht die Ausführung der Befestigung am Gebäude.
Blocs-portes pour piétons, fenêtres, façades rideaux, grilles et fermetures - Résistance à l'effraction - Méthode d'essai pour la détermination de la résistance aux tentatives manuelles d'effraction
Le présent document définit la méthode d’essai visant à déterminer la résistance aux tentatives d’effraction manuelle dans le but d’évaluer les caractéristiques de résistance à l’effraction des blocs portes pour piétons, fenêtres, façades rideaux, grilles et fermetures. Il s’applique aux constructions fixes et aux systèmes ouvrants suivants : battant, oscillant, pliant, oscillo battant, à gonds haut ou bas, coulissant (horizontalement et verticalement), pivotant (horizontalement et verticalement) et à enroulement.
Le présent document ne traite pas directement de la résistance aux ouvertures fines des serrures et des cylindres. Il ne couvre pas non plus l’attaque des produits de construction résistants à l’effraction actionnés de façon électrique, électronique et électromagnétique, à l’aide de méthodes susceptibles de neutraliser ces caractéristiques.
Les instructions de pose du fabricant donnent des recommandations relatives à la fixation du produit.
Un exemple du contenu des instructions de pose du fabricant est donné à l’Annexe A du prEN 1627:2019.
Le présent document ne s’applique pas aux portes, portails et barrières, destinés à être installés dans des zones accessibles aux personnes et dont l’utilisation principale prévue est de permettre l’accès sécurisé de marchandises et de véhicules accompagnés ou conduits par des personnes, dans des locaux industriels et commerciaux ou des garages dans les zones d’habitation, tel que traité par l’EN 13241.
Il est reconnu que les performances de résistance à l’effraction des produits de construction se caractérisent par deux aspects : leur résistance normale à une ouverture en force et leur capacité à rester fixé au bâtiment. Cette méthode d’essai n’évalue pas les performances de la fixation à la structure du bâtiment.
Vrata, okna, obešene fasade, mreže in polkna - Protivlomna odpornost - Preskusna metoda za ugotavljanje odpornosti proti poskusu ročnega vloma
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1630:2021
01-september-2021
Nadomešča:
SIST EN 1630:2012+A1:2016
Vrata, okna, obešene fasade, mreže in polkna - Protivlomna odpornost - Preskusna
metoda za ugotavljanje odpornosti proti poskusu ročnega vloma
Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance -
Test method for the determination of resistance to manual burglary attempts
Türen, Fenster, Vorhangfassaden, Gitterelemente und Abschlüsse - Einbruchhemmung -
Prüfverfahren für die Ermittlung der Widerstandsfähigkeit gegen manuelle
Einbruchversuche
Blocs-portes pour piétons, fenêtres, façades rideaux, grilles et fermetures - Résistance à
l'effraction - Méthode d'essai pour la détermination de la résistance aux tentatives
manuelles d'effraction
Ta slovenski standard je istoveten z: EN 1630:2021
ICS:
13.310 Varstvo pred kriminalom Protection against crime
91.060.50 Vrata in okna Doors and windows
SIST EN 1630:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1630:2021
---------------------- Page: 2 ----------------------
SIST EN 1630:2021
EN 1630
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2021
EUROPÄISCHE NORM
ICS 13.310; 91.060.50 Supersedes EN 1630:2011+A1:2015
English Version
Pedestrian doorsets, windows, curtain walling, grilles and
shutters - Burglar resistance - Test method for the
determination of resistance to manual burglary attempts
Blocs-portes pour piétons, fenêtres, façades rideaux, Türen, Fenster, Vorhangfassaden, Gitterelemente und
grilles et fermetures - Résistance à l'effraction - Abschlüsse - Einbruchhemmung - Prüfverfahren für die
Méthode d'essai pour la détermination de la résistance Ermittlung der Widerstandsfähigkeit gegen manuelle
aux tentatives manuelles d'effraction Einbruchversuche
This European Standard was approved by CEN on 19 March 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1630:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1630:2021
EN 1630:2021 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Apparatus and test team. 7
4.1 Test rig . 7
4.2 Test team . 7
4.2.1 Personnel . 7
4.2.2 Composition of the test team . 7
4.2.3 Essential capabilities of the test team members . 7
4.2.4 Training . 8
4.3 Measurement and recording devices . 8
4.3.1 Measuring equipment . 8
4.3.2 Video recording . 8
4.4 Tolerances . 9
4.5 Sub-frame . 9
4.6 Cylinder plug extraction . 9
5 Test specimen . 9
5.1 General . 9
5.1.1 General . 9
5.1.2 Product with glazing . 10
5.2 Preparation and examination of the specimen . 10
6 Procedure. 11
6.1 General . 11
6.2 Test room climate . 11
6.3 Areas of attack . 11
6.3.1 General . 11
6.3.2 Construction products with moving elements . 11
6.3.3 Fixed construction products . 12
6.4 Attack side and attack height . 12
6.5 Pre-test . 12
6.6 Main test . 12
6.7 Failure criteria . 13
7 Tool sets . 13
7.1 General . 13
7.2 Tool set A1 resistance class 1 (see Figure A.1) – Application of the tool set A1 in
resistance class 1 . 13
7.3 Tool set A2 resistance class 2 (see Figure A.2) – Application of the tool set A2 in
resistance class 2 . 14
7.4 Tool set A3 resistance class 3 (see Table 4 and Figure A.3) – Application of the tool
set A3 in resistance class 3 . 15
7.5 Tool set A4 resistance class 4 (see Table 5 and Figure A.4) – Application of the tool
set A4 in resistance class 4 . 16
2
---------------------- Page: 4 ----------------------
SIST EN 1630:2021
EN 1630:2021 (E)
7.6 Tool set A5 resistance class 5 (see Table 6 and Figure A.5) – Application of the tool
set A5 in resistance class 5 . 16
7.7 Tool set A6 resistance class 6 (see Table 7 and Figure A.6) – Application of the tool
set A6 in resistance class 6 . 17
8 Test report . 18
Annex A (normative) Tool sets. 19
Annex B (normative) Test sequence for manual test. 25
Annex C (normative) Example of test equipment . 26
Annex D (informative) Examples of mounting arrangements . 27
Annex E (normative) Cylinder plug extraction . 42
Annex F (normative) Tests for building elements with non-key operated lockable hardware . 44
Bibliography . 47
3
---------------------- Page: 5 ----------------------
SIST EN 1630:2021
EN 1630:2021 (E)
European foreword
This document (EN 1630:2021) has been prepared by Technical Committee CEN/TC 33 “Doors, windows,
shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2021, and conflicting national standards shall
be withdrawn at the latest by December 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1630:2011+A1:2015.
Significant changes in this revision are:
a) updated editions of Normative References;
b) Annex E and Annex F added;
c) for certain test the template E4 was added in 6.7;
d) the figures in Annex A have been updated.
This document is one of a series of standards for burglar resistant pedestrian doorsets, windows, curtain
walling, grilles and shutters. The other standards in the series are:
— EN 1627:2021 Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar resistance
— Requirements and classification;
— EN 1628:2021, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar
resistance — Test method for the determination of resistance under static loading;
— EN 1629:2021, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar
resistance — Test method for the determination of resistance under dynamic loading.
The manual test described in this document covers the areas of vulnerability not suitably assessed by the
static loading and dynamic loading tests described in EN 1628:2021 and EN 1629:2021. Certain basic
security requirements for the locks, furniture and cylinders are covered by the requirements detailed in
EN 1627:2021, Table 3. These security characteristics are not re-assessed in this test standard and the
attack methods and test times have been limited to reflect this.
The use of the tools detailed in the various tools sets is described in this document. This has the advantage
of improving the reproducibility of the test.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
4
---------------------- Page: 6 ----------------------
SIST EN 1630:2021
EN 1630:2021 (E)
1 Scope
This document specifies a test method for the determination of resistance to manual burglary attempts
in order to assess the burglar resistant characteristics of pedestrian doorsets, windows, curtain walling,
grilles and shutters. It is applicable to the following opening functions: turning, tilting, folding, turn-
tilting, top or bottom hung, sliding (horizontally and vertically), pivoted (horizontally and vertically),
projecting, and rolling as well as non-openable constructions.
This document does not directly cover the resistance of locks and cylinders to attack with picking tools.
It also does not cover the attack of electric, electronic and electromagnetic operated burglar resistant
construction products using surreptitious attack methods that might defeat these characteristics.
It is acknowledged that there are two aspects to the burglar resistance performance of construction
products, their normal resistance to forced operation and their ability to remain fixed to the building.
This test method does not evaluate the performance of the fixing to the building.
The manufacturer's installation instructions will give guidance on the fixing of the product.
An example for the contents of the manufacturer’s installation instructions is given in EN 1627:2021,
Annex A.
This document does not apply to walls and roofs, as well as for doors, gates and barriers, intended for
installation in areas in the reach of persons, and for which the main intended uses are giving safe access
for goods and vehicles accompanied or driven by persons in industrial, commercial or residential
premises, as covered by EN 13241:2003+A2:2016.
NOTE It is important that construction products that can be reached or driven through by vehicles are
protected by appropriate measures such as barriers, extensible ramps, etc.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 356:1999, Glass in building — Security glazing — Testing and classification of resistance against
manual attack
EN 1303:2015, Building hardware — Cylinders for locks - Requirements and test methods
EN 1627:2021, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar resistance —
Requirements and classification
EN 1628:2021, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar resistance —
Test method for the determination of resistance under static loading
EN 1629:2021, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar resistance —
Test method for the determination of resistance under dynamic loading
EN 12216:2018, Shutters, external blinds, internal blinds — Terminology, glossary and definitions
EN 12519:2018, Windows and pedestrian doors — Terminology
EN 13119:2016, Curtain walling — Terminology
EN ISO 10666:1999, Drilling screws with tapping screw thread — Mechanical and functional properties
(ISO 10666:1999)
5
---------------------- Page: 7 ----------------------
SIST EN 1630:2021
EN 1630:2021 (E)
EN ISO 15480:2019, Fasteners — Hexagon washer head drilling screws with tapping screw thread
(ISO 15480:2019)
EN ISO 15481:1999, Cross recessed pan head drilling screws with tapping screw thread (ISO 15481:1999)
EN ISO 15482:1999, Cross recessed countersunk head drilling screws with tapping screw thread
(ISO 15482:1999)
EN ISO 15483:1999, Cross recessed raised countersunk head drilling screws with tapping screw thread
(ISO 15483:1999)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1627:2021, EN 12519:2018, EN
12216:2018, EN 13119:2016 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
test specimen
complete, fully functioning construction product as detailed in the scope of this document
3.2
sub-frame
standard surrounding frame into which the test specimen is mounted for testing purpose
3.3
test rig
surrounding substantial steel frame with movable steel supports into which the sub-frames containing
test specimens of various dimensions can be mounted
3.4
tool set
set of tools allocated for use for a particular resistance class
Note 1 to entry: For details of the tool set, see Clause 7 and Annex A.
3.5
rest time
time taken when the test person carrying out the manual burglary test interrupts his work for a rest
3.6
tool change time
time for the exchange or replacement of a tool or a part thereof, e.g. a defective drill, a blunt saw blade,
etc.
3.7
observation time
time required for the test team to observe the test and to decide on its further execution
6
---------------------- Page: 8 ----------------------
SIST EN 1630:2021
EN 1630:2021 (E)
3.8
total test time
combination of the resistance times, the rest times, the times for tool changes and the observation times
during the main test
Note 1 to entry: The maximum total test time is the sum of the resistance time, rest time, tool change time and
observation time. Resistance time is the working time of the test person carrying out the manual burglary test. The
resistance time includes times of less than 5 s each for tool changes, e.g. exchanging a screwdriver for a crowbar.
3.9
accessible opening
opening permitting a test block of cross section of any of the dimensions defined in 6.7 to be passed
through it
4 Apparatus and test team
4.1 Test rig
The test rig shall consist of a rigid frame into which test specimens can be mounted with their subframes.
Annex C, Figure C.1 shows an example of a test rig. The stiffness of the rig shall be such that a 15 kN force
applied to any of the defined points shall not cause a deflection of more than 5 mm. The test rig shall
support the subframe. The test rig shall not impede the execution of the test.
4.2 Test team
4.2.1 Personnel
The requirements for the test team personnel should be in accordance with EN ISO/IEC 17025:2017, 6.2.
4.2.2 Composition of the test team
The test team shall comprise a minimum of two people.
At least two members of the test team shall be capable of performing the manual test.
At least one member of the test team shall be competent to record the data and observations in such a
way that a test report can be established.
For each test in an area of attack only one test team member shall be permitted.
4.2.3 Essential capabilities of the test team members
In order to perform the manual test, test team members shall be able to demonstrate that they are:
— mentally alert and well-motivated to maintain a sustained burglary attack;
— physically able to perform the test, and are able to withstand the physical strain likely to be imposed
for the duration of the test;
— free from mobility impairments and have normal vision, corrected where necessary;
— capable of reflecting current modus operandi during burglary attacks using reasonable but not
excessive force reflecting the anticipated attack relevant to the resistance class.
7
---------------------- Page: 9 ----------------------
SIST EN 1630:2021
EN 1630:2021 (E)
In addition, the test team shall be able to demonstrate detailed knowledge and understanding of:
— the design and manufacture of burglar resistant construction products including the locks, building
hardware and materials used;
— current modus operandi during burglary attacks;
— operation and control of test equipment;
— operation, control and maintenance of the attack tool sets;
— operation, control and maintenance of the measuring equipment;
— the handling of the tools used when performing the test for burglar resistance.
4.2.4 Training
The test team shall have the opportunity for continuous development of skills and expertise appropriate
to the performance of the tests, including:
— checking and assessing of video recording of the tests by the test team;
NOTE Video records can also form the basis for demonstrating the competence of test team members.
— the exchange of knowledge and experience between testing bodies and police agencies;
— further training, e.g. measuring techniques, material information, new construction products, new
opening and closing techniques.
4.3 Measurement and recording devices
4.3.1 Measuring equipment
The following equipment shall be available:
a) chronometer for measuring the resistance time;
b) chronometer for measuring the total test time;
c) equipment for determining temperature and relative humidity.
4.3.2 Video recording
The pre-test and the main test conducted on each test specimen shall be fully video recorded. The video
and any copies of it shall not be published nor shown publicly without the permission of both the
applicant and the test lab.
The video may be used as a reference when subsequent changes are made to the product.
A time reference or code should be shown in the video.
When a test laboratory is asked to conduct the test and a video is recorded, the test laboratory should
include restrictions on the use of the video in their terms and conditions of contract with the applicant.
The test laboratory should take precautions to be in line with the EU General Data Protection Regulation.
8
---------------------- Page: 10 ----------------------
SIST EN 1630:2021
EN 1630:2021 (E)
4.4 Tolerances
Unless stated otherwise in this document the following tolerances shall apply to the test equipment:
— Time ±1 %
— Temperature ±1°
— Relative humidity ±5 %
4.5 Sub-frame
The sub-frame shall simulate the support given to the product when installed into a building. It shall
typically consist of the following:
a) for group 1 to group 4 products, a rectangular minimum metal tube 120 mm × 120 mm × 5 mm or a
rectangular timber frame minimum 100 mm × 70 mm;
NOTE High quality wood, e.g. glue laminated timber.
b) additionally for group 3 products and group 4 products, a steel tube 40 mm × 40 mm × 3 mm and a
base plate of 8 mm steel, consisting of several segments which shall be removable for the purposes
of loading, if necessary.
4.6 Cylinder plug extraction
When cylinders do not fulfil EN 1627:2021, Table 3, the cylinder plug extraction shall be conducted in
accordance with Annex E.
5 Test specimen
5.1 General
5.1.1 General
The test specimen shall be a functioning product complete with its frames, building hardware, guide rails,
curtain, tube, roller box and accessories, as appropriate.
The test specimen shall be fixed square and plumb and without twist or bend into a sub-frame.
The manufacturer shall ensure that the method of fixing, packing supports, sealing requirements, etc. of
the test specimen into the sub-frame are in accordance with their installation instructions (see
EN 1628:2021, Figures A.15 to A.63). The sub-frame shall be supported by the test rig so that there will
be no movement of the sub-frame during the test.
Installation shall be carried out in accordance with the manufacturer's instructions as detailed in
EN 1627:2021, Clause 10 including the method of fixing, packing supports, sealing requirements etc., as
shown in Annex D, Figures D.1 to D.18. The test specimen shall be located in the test rig at a height relative
to ground, nominally the same as intended in use, i.e. doors and French windows shall be mounted at
ground level and windows shall be mounted at a height of 800 mm from ground level. The test specimen
shall be installed in the sub-frame and test rig as close to the tester as possible to give maximum access
to the test specimen.
For products intended to be installed in orientations other than vertical (e.g. rooflights) the test specimen
shall be tested in the orientation of its intended use. When a range of intended orientations is considered,
the test shall be performed in the most vulnerable orientation for the test specimen.
The number of test specimens needed is described in EN 1627:2021, Clause 11.
NOTE Under particular circumstances, additional specimens might be required.
9
---------------------- Page: 11 ----------------------
SIST EN 1630:2021
EN 1630:2021 (E)
The specimen used in the static test carried out in accordance with EN 1628:2021, and in the dynamic
test carried out in accordance with EN 1629:2021, can also be used in the pre-test, provided that any
damage caused by those tests will not affect the result of the pre-test.
5.1.2 Product with glazing
For the purposes of testing according to this document, the test specimen shall be glazed according to the
relevant glazing resistance class of EN 356:1999, as shown in Table 1.
Table 1 — Glazing requirements for the test specimen
Resistance class Minimum resistance class of glazing according to
EN 356:1999 fitted on the test specimen for testing purpose
RC 1 N P4 A
RC 1 a
P4 A
RC 2 N P4 A
RC 2 a
P4 A
RC 3 a
P5 A
RC 4 a
P6 B
RC 5 a
P7 B
RC 6 a
P8 B
a
The glazing type fitted on the test specimen shall be the type (or one of the types) used for
classification purpose.
If a glass unit with a higher security level is used within the specimen used for the tests, it may not be
possible to assess the use of glass units with a lower grade within those products without conducting
further tests. This is because higher grades of glass can increase the rigidity of the product.
5.2 Preparation and examination of the specimen
The specimen shall be stored for at least 8 h in a temperature range between 15 °C and 30 °C until the
start of the test to ensure that it is fully tempered for the test.
The test specimen and sub-frame mounted in the test rig shall be visually examined for damage, defects
or other particular conditions of finish, etc. These shall be recorded.
The test specimen shall be in the closed condition specified by the manufacturer.
Each test specimen shall be examined and the direction to disengage each locking point shall be noted.
All locking hardware that can be disengaged from the attack side without the use of a key or tool shall be
disengaged during all tests.
NOTE This includes, for example, non-arresting latch bolts which are not engaged in the locking position.
The applicant shall supply the specimen pre-fitted in sub-frames (timber, aluminium or steel box section),
with the maximum permitted gap between the specimen frame and the sub-frame, according to their
installation instructions. The installation details and gap size shall be recorded in the test report. During
test the tes
...
SLOVENSKI STANDARD
oSIST prEN 1630:2019
01-julij-2019
Vrata, okna, obešene fasade, mreže in polkna - Protivlomna odpornost -
Preskusna metoda za ugotavljanje odpornosti proti poskusu ročnega vloma
Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance -
Test method for the determination of resistance to manual burglary attempts
Türen, Fenster, Vorhangfassaden, Gitterelemente und Abschlüsse - Einbruchhemmung -
Prüfverfahren für die Ermittlung der Widerstandsfähigkeit gegen manuelle
Einbruchversuche
Blocs-portes pour piétons, fenêtres, façades rideaux, grilles et fermetures - Résistance à
l'effraction - Méthode d'essai pour la détermination de la résistance aux tentatives
manuelles d'effraction
Ta slovenski standard je istoveten z: prEN 1630
ICS:
13.310 Varstvo pred kriminalom Protection against crime
91.060.50 Vrata in okna Doors and windows
oSIST prEN 1630:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 1630:2019
---------------------- Page: 2 ----------------------
oSIST prEN 1630:2019
DRAFT
EUROPEAN STANDARD
prEN 1630
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2019
ICS 13.310; 91.060.50 Will supersede EN 1630:2011+A1:2015
English Version
Pedestrian doorsets, windows, curtain walling, grilles and
shutters - Burglar resistance - Test method for the
determination of resistance to manual burglary attempts
Blocs-portes pour piétons, fenêtres, façades rideaux, Türen, Fenster, Vorhangfassaden, Gitterelemente und
grilles et fermetures - Résistance à l'effraction - Abschlüsse - Einbruchhemmung - Prüfverfahren für die
Méthode d'essai pour la détermination de la résistance Ermittlung der Widerstandsfähigkeit gegen manuelle
aux tentatives manuelles d'effraction Einbruchversuche
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 33.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1630:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 1630:2019
prEN 1630:2019 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Apparatus and test team. 7
4.1 Test rig . 7
4.2 Test team . 7
4.2.1 Personnel . 7
4.2.2 Composition of the test team . 7
4.2.3 Essential capabilities of the test team members . 7
4.2.4 Training . 8
4.3 Measurement and recording devices . 8
4.3.1 Measuring equipment . 8
4.3.2 Video recording . 8
4.4 Tolerances . 8
4.5 Sub-frame . 8
4.6 Cylinder plug extraction . 9
5 Test specimen . 9
5.1 General . 9
5.1.1 General . 9
5.1.2 Product with glazed infilling . 9
5.2 Preparation and examination of the specimen . 10
6 Procedure. 10
6.1 General . 10
6.2 Test room climate . 10
6.3 Areas of attack . 11
6.3.1 General . 11
6.3.2 Construction products with moving elements . 11
6.3.3 Fixed construction products . 11
6.4 Attack side and attack height . 11
6.5 Pre-test . 11
6.6 Main test . 12
6.7 Failure criteria . 12
7 Tool sets . 12
7.1 General . 12
7.2 Tool set A1 resistance class 1 (see Figure A.1) – Application of the tool set A1 in
resistance class 1 . 13
7.3 Tool set A2 resistance class 2 (see Figure A.2) – Application of the tool set A2 in
resistance class 2 . 14
7.4 Tool set A3 resistance class 3 (see Figure A.3) – Application of the tool set A3 in
resistance class 3 . 14
7.5 Tool set A4 resistance class 4 (see Figure A.4) – Application of the tool set A4 in
resistance class 4 . 15
2
---------------------- Page: 4 ----------------------
oSIST prEN 1630:2019
prEN 1630:2019 (E)
7.6 Tool set A5 resistance class 5 (see Figure A.5) – Application of the tool set A5 in
resistance class 5 . 15
7.7 Tool set A6 resistance class 6 (see Figure A.6) – Application of the tool set A6 in
resistance class 6 . 16
8 Test report . 17
Annex A (normative) Tool sets . 18
A.1 Tool set A1 . 18
A.2 Tool set A2 . 19
A.3 Tool set A3 . 20
A.4 Tool set A4 . 21
A.5 Tool set A5 . 22
A.6 Tool set A6 . 23
Annex B (normative) Test sequence for manual test of resistance classes 2 to 6 . 24
B.1 Test sequence for manual test of resistance classes 2 to 6. 24
Annex C (normative) Example of test equipment . 25
Annex D (informative) Examples of mounting arrangements . 26
D.1 Examples of mounting arrangements for doorsets . 26
D.2 Examples of mounting arrangements for windows . 29
D.3 Examples of mounting arrangements for wing and folding shutters . 32
D.4 Examples of mounting arrangements for guide rails and roller shutters into the test
rig . 34
D.5 Examples of mounting arrangements for grilles into the test rig . 38
Annex E (normative) Cylinder plug extraction . 41
E.1 General . 41
E.2 Cylinder plug extraction . 41
Bibliography . 43
3
---------------------- Page: 5 ----------------------
oSIST prEN 1630:2019
prEN 1630:2019 (E)
European foreword
This document (prEN 1630:2019) has been prepared by Technical Committee CEN/TC 33 “Doors,
windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document supersedes EN 1630:2011+A1:2015.
Significant changes in this revision are:
a) updated editions of Normative references;
b) Annex E added.
This document is one of a series of standards for burglar resistant pedestrian doorsets, windows, curtain
walling, grilles and shutters. The other standards in the series are:
— prEN 1627:2019, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar
resistance — Requirements and classification;
— prEN 1628:2019, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar
resistance — Test method for the determination of resistance under static loading;
— prEN 1629:2019, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar
resistance — Test method for the determination of resistance under dynamic loading.
The manual test described in this standard covers the areas of vulnerability not suitably assessed by the
static loading and dynamic loading tests described in prEN 1628:2019 and prEN 1629:2019. Certain
basic security requirements for the locks, furniture and cylinders are covered by the requirements
detailed in Table 10 of prEN 1627:2019. These security characteristics are not re-assessed in this test
standard and the attack methods and test times have been limited to reflect this.
The use of the tools detailed in the various tools sets is described in this standard. This has the advantage
of improving the reproducibility of the test.
4
---------------------- Page: 6 ----------------------
oSIST prEN 1630:2019
prEN 1630:2019 (E)
1 Scope
This document specifies a test method for the determination of resistance to manual burglary attempts
in order to assess the burglar resistant characteristics of pedestrian doorsets, windows, curtain walling,
grilles and shutters. It is applicable to the following means of opening: turning, tilting, folding, turn-tilting,
top or bottom hung, sliding (horizontally and vertically), pivoted (horizontally and vertically) and rolling
as well as fixed constructions.
This document does not directly cover the resistance of locks and cylinders to attack with picking tools.
It also does not cover the attack of electric, electronic and electromagnetic operated burglar resistant
construction products using attack methods that might defeat these characteristics.
The manufacturer's installation instructions will give guidance on the fixing of the product.
An example for the contents of the manufacturer’s installation instructions is given in Annex A of
prEN 1627:2019.
This document does not apply to doors, gates and barriers, intended for installation in areas in the reach
of persons, and for which the main intended uses are giving safe access for goods and vehicles
accompanied or driven by persons in industrial, commercial or residential premises, as covered by
EN 13241.
It is acknowledged that there are two aspects to the burglar resistance performance of construction
products, their normal resistance to forced operation and their ability to remain fixed to the building.
This test method does not evaluate the performance of the fixing to the building.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 356:1999, Glass in building - Security glazing - Testing and classification of resistance against manual
attack
EN 1303:2015, Building hardware - Cylinders for locks - Requirements and test methods
prEN 1627:2019, Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance -
Requirements and classification
prEN 1628:2019, Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance -
Test method for the determination of resistance under static loading
prEN 1629:2019, Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance -
Test method for the determination of resistance under dynamic loading
EN ISO 10666, Drilling screws with tapping screw thread - Mechanical and functional properties (ISO
10666)
EN ISO 15480, Hexagon washer head drilling screws with tapping screw thread (ISO 15480)
EN ISO 15481, Cross recessed pan head drilling screws with tapping screw thread (ISO 15481)
EN ISO 15482, Cross recessed countersunk head drilling screws with tapping screw thread (ISO 15482)
EN ISO 15483, Cross recessed raised countersunk head drilling screws with tapping screw thread (ISO
15483)
5
---------------------- Page: 7 ----------------------
oSIST prEN 1630:2019
prEN 1630:2019 (E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in prEN 1627:2019 and the following
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
test specimen
complete, fully functioning construction product as detailed in the scope of this standard
3.2
sub-frame
surrounding frame into which the test specimen is mounted in accordance with the manufacturer’s
instructions
3.3
test rig
surrounding substantial steel frame with movable steel supports into which the sub-frames containing
test specimens of various dimensions can be mounted
3.4
tool set
set of tools allocated for use for a particular resistance class
Note 1 to entry: For details of the tool set, see Clause 7 and Annex A.
3.5
rest time
time taken when the test person carrying out the manual burglary test interrupts his work for a rest
3.6
tool change time
time for the exchange or replacement of a tool or a part thereof, e.g. a defective drill, a blunt saw blade,
etc
3.7
observation time
time required for the test team to observe the test and to decide on its further execution
3.8
total test time
combination of the resistance times, the rest times, the times for tool changes and the observation times
during the main test
Note 1 to entry: The maximum total test time is the sum of the resistance time, rest time, tool change time and
observation time. Resistance time is the working time of the test person carrying out the manual burglary test. The
resistance time includes times of less than 5 s each for tool changes, e.g. exchanging a screwdriver for a crowbar.
6
---------------------- Page: 8 ----------------------
oSIST prEN 1630:2019
prEN 1630:2019 (E)
3.9
accessible opening
opening permitting a test block of cross section of any of the dimensions defined in 6.7 to be passed
through it
4 Apparatus and test team
4.1 Test rig
The test rig shall consist of a rigid frame into which test specimens can be mounted with its subframe.
Annex C, Figure C.1 shows an example of a test rig. The stiffness of the rig shall be such that a 15 kN force
applied to any of the defined points shall not cause a deflection of more than 5 mm. The test rig shall
support the subframe. The test rig shall not impede the execution of the test.
4.2 Test team
4.2.1 Personnel
The requirements for the test team personnel should be in accordance with EN ISO/IEC 17025:2017, 6.2.
4.2.2 Composition of the test team
The test team shall comprise a minimum of two people.
At least two members of the test team shall be capable of performing the manual test.
At least one member of the test team shall be competent to record the data and observations in such a
way that a test report can be established.
For each test in an area of attack only one test team member shall be permitted.
4.2.3 Essential capabilities of the test team members
In order to perform the manual test, test team members shall be able to demonstrate that they are:
— mentally alert and well-motivated to maintain a sustained burglary attack;
— physically able to perform the test, and are able to withstand the physical strain likely to be imposed
for the duration of the test;
— free from mobility impairments and have normal vision, corrected where necessary;
— capable of reflecting current modus operandi during burglary attacks using reasonable but not
excessive force reflecting the anticipated attack relevant to the resistance class.
In addition, the test team shall be able to demonstrate detailed knowledge and understanding of:
— the design and manufacture of burglar resistant construction products including the locks, hardware
and materials used;
— current modus operandi during burglary attacks;
— operation and control of test equipment;
— operation, control and maintenance of the attack tool sets;
— operation, control and maintenance of the measuring equipment;
— the handling of the tools used when performing the test for burglar resistance.
7
---------------------- Page: 9 ----------------------
oSIST prEN 1630:2019
prEN 1630:2019 (E)
4.2.4 Training
The test team shall have the opportunity for continuous development of skills and expertise appropriate
to the performance of the tests, including:
— checking and assessing of video recording of the tests by the test team;
NOTE Video records can also form the basis for demonstrating the competence of test team members.
— the exchange of knowledge and experience between testing bodies and police agencies;
— further training, e.g. measuring techniques, material information, new construction products, new
opening and closing techniques.
4.3 Measurement and recording devices
4.3.1 Measuring equipment
The following equipment shall be provided:
a) chronometer for measuring the resistance time;
b) chronometer for measuring the total test time;
c) equipment for determining temperature and relative humidity.
4.3.2 Video recording
The pre-test and the main test conducted on each test specimen shall be fully recorded with a video
recorder. The video and any copies of it shall not be published nor shown publicly without the permission
of both the applicant and the test lab.
The video may be used as a reference when subsequent changes are made to the product.
A time reference or code should be shown in the video.
When a test laboratory is asked to conduct the test and a video is recorded, the test laboratory should
include restrictions on the use of the video in their terms and conditions of contract with the submitter.
4.4 Tolerances
Unless stated otherwise in this European Standard the following tolerances shall apply to the test
equipment:
— Time ±1 %
— Temperature ±1°
— Relative humidity ±5 %
4.5 Sub-frame
The sub-frame shall simulate the support given to the product when installed into a building and shall be
taken into consideration in the manufacturer’s installation instructions. It shall typically consist of the
following:
a) for group 1 to group 4 products, a rectangular metal tube 120 mm x 120 mm x 5 mm or a rectangular
timber frame 100 mm x 50 mm;
8
---------------------- Page: 10 ----------------------
oSIST prEN 1630:2019
prEN 1630:2019 (E)
b) additionally for group 3 products and group 4 products, a steel tube 40 mm x 40 mm x 3 mm and a
base plate of 8 mm steel, consisting of several segments which shall be removable for the purposes
of loading, if necessary.
4.6 Cylinder plug extraction
The cylinder plug extraction shall be as given in Annex E.
5 Test specimen
5.1 General
5.1.1 General
The test specimen shall be a functioning product complete with its frames, hardware, guide rails, curtain,
tube, roller box and accessories, as appropriate.
The test specimen shall be fixed square and plumb and without twist or bend into a sub-frame.
Installation shall be carried out in accordance with the manufacturer's instructions as detailed in
Clause 10 of prEN 1627:2019, including the method of fixing, packing supports, sealing requirements etc.,
as shown in Annex D, Figures D.1 to D.18. The test specimen shall be located in the test rig at a height
relative to ground, nominally the same as intended in use. i.e. doors and French windows shall be
mounted at ground level and windows shall be mounted at a height of 800 mm from ground level. The
test specimen shall be installed in the sub-frame and test rig as close to the tester as possible to give
maximum access to the test specimen.
For products intended to be installed in orientations other than vertical (e.g. rooflights) the test specimen
shall be tested in the orientation of its intended use. When a range of intended orientations is considered,
the test shall be performed in the most vulnerable orientation for the test specimen.
The number of test specimens needed is described in prEN 1627:2019, Clause 11.
NOTE 1 Under particular circumstances, additional specimens might be required.
NOTE 2 The specimen used in the static test carried out in accordance with prEN 1628:2019, and in the dynamic
test carried out in accordance with prEN 1629:2019, can also be used in the pre-test, provided that any damage
caused by those tests will not affect the result of the pre-test.
5.1.2 Product with glazed infilling
For the purposes of testing according to this standard, the test specimen shall be glazed according to the
relevant glazing resistance class of EN 356:1999, as shown in Table 1.
9
---------------------- Page: 11 ----------------------
oSIST prEN 1630:2019
prEN 1630:2019 (E)
Table 1 — Test sample glazing requirements for test specimen
Resistance class Minimum resistance class of glazing according to
EN 356:1999 fitted on the test specimen for testing
purpose
RC 1 N P4 A
RC 2 N P4 A
a
RC 2 P4 A
a
RC 3 P5 A
a
RC 4 P6 B
a
RC 5 P7 B
a
RC 6 P8 B
a
The glazed infilling type fitted on the test specimen shall be the type (or one of the types) used
for classification purpose.
NOTE If a higher grade of glass is used in the test specimen, it may not be possible to assess the use of lower
grade glass within those products without conducting further tests. This is because higher grades of glass can
increase the rigidity of the product.
5.2 Preparation and examination of the specimen
The temperature of the test specimen shall be maintained between 15 °C and 30 °C for a period of not
less than 8 h prior to test.
The test specimen and sub-frame mounted in the test rig shall be visually examined for damage, defects
or other particular conditions of finish, etc. These shall be recorded.
The test specimen shall be in the closed condition specified by the manufacturer.
Each test specimen shall be examined and the direction to disengage each locking point shall be noted.
All locking hardware that can be disengaged from the attack side without the use of a key or tool shall be
disengaged during all tests.
NOTE This includes, for example, non-arresting latch bolts which are not engaged in the locking position.
The applicant shall supply the specimens pr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.