SIST EN 62271-209:2008
(Main)High-voltage switchgear and controlgear -- Part 209: Cable connections for gas-insulated metal-enclosed switchgear for rated voltages above 52 kV - Fluid-filled and extruded insulation cables - Fluid-filled and dry-type cable-terminations
High-voltage switchgear and controlgear -- Part 209: Cable connections for gas-insulated metal-enclosed switchgear for rated voltages above 52 kV - Fluid-filled and extruded insulation cables - Fluid-filled and dry-type cable-terminations
This standard covers the connection assembly of fluid-filled and extruded cables to gasinsulated metal enclosed switchgear (GIS), in single- or three-phase arrangements where the cable-terminations are fluid-filled or dry type and there is a separating insulating barrier between the cable insulation and the gas insulation of the switchgear. The purpose of this standard is to establish electrical and mechanical interchangeability between cable-terminations and the gas-insulated metal-enclosed switchgear and to determine the limits of supply. It complements and amends, if necessary, the relevant IEC standards. For the purpose of this standard the term "switchgear" is used for "gas-insulated metal enclosed switchgear". It does not cover directly immersed cable terminations, as described in CIGRE brochure 89.
Hochspannungs-Schaltgeräte und -Schaltanlagen -- Teil 209: Kabelanschlüsse für gasisolierte metallgekapselte Schaltanlagen für Bemessungsspannungen über 52 kV - Kabel mit fluidgefüllter und extrudierter Isolierung - Fluidgefüllte und feststoffisolierte Kabelendverschlüsse
Appareillage à haute tension -- Partie 209: Raccordement de câbles pour appareillage sous enveloppe métallique à isolation gazeuse de tension assignée supérieure à 52 kV - Câbles remplis d'un fluide ou à isolation extrudée - Extrémité de câble sèche ou remplie d'un fluide
La présente norme est applicable à l'assemblage de raccordement de câbles remplis d'un fluide ou à isolation extrudée à l'appareillage sous enveloppe métallique à isolation gazeuse (PSEM), dans une disposition unipolaire ou tripolaire. Les extrémités de câble sont à remplissage de fluide ou sèches et une séparation isolante se trouve entre le fluide d'isolation du câble et l'isolation gazeuse de l'appareillage.
Visokonapetostne stikalne naprave - 209. del: Kabelski spoji za plinsko izolirane stikalne naprave v kovinskih ohišjih za naznačene napetosti nad 52 kV - Kabli v tekočini in z ekstrudirano izolacijo - Mokri in suhi kabelski priključki (IEC 62271-209:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62271-209:2008
01-februar-2008
9LVRNRQDSHWRVWQHVWLNDOQHQDSUDYH GHO .DEHOVNLVSRML]DSOLQVNRL]ROLUDQH
VWLNDOQHQDSUDYHYNRYLQVNLKRKLãMLK]DQD]QDþHQHQDSHWRVWLQDGN9.DEOLY
WHNRþLQLLQ]HNVWUXGLUDQRL]RODFLMR0RNULLQVXKLNDEHOVNLSULNOMXþNL ,(&
High-voltage switchgear and controlgear - Part 209: Cable connections for gas-insulated
metal-enclosed switchgear for rated voltages above 52 kV - Fluid-filled and extruded
insulation cables - Fluid-filled and dry-type cable-terminations (IEC 62271-209:2007)
Hochspannungs-Schaltgeräte und -Schaltanlagen - Teil 209: Kabelanschlüsse für
gasisolierte metallgekapselte Schaltanlagen für Bemessungsspannungen über 52 kV -
Kabel mit fluidgefüllter und extrudierter Isolierung - Fluidgefüllte und feststoffisolierte
Kabelendverschlüsse (IEC 62271-209:2007)
Appareillage haute tension - Partie 209: Raccordement de câbles pour appareillage sous
enveloppe métallique a isolation gazeuse de tension assignée supérieure a 52 kV -
Câbles remplis d'un fluide ou a isolation extrudée - Extrémité de câble seche ou remplie
d'un fluide (IEC 62271-209:2007)
Ta slovenski standard je istoveten z: EN 62271-209:2007
ICS:
29.130.10 Visokonapetostne stikalne in High voltage switchgear and
krmilne naprave controlgear
SIST EN 62271-209:2008 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 62271-209
NORME EUROPÉENNE
November 2007
EUROPÄISCHE NORM
ICS 29.130.10
English version
High-voltage switchgear and controlgear -
Part 209: Cable connections for gas-insulated metal-enclosed switchgear
for rated voltages above 52 kV -
Fluid-filled and extruded insulation cables -
Fluid-filled and dry-type cable-terminations
(IEC 62271-209:2007)
Appareillage à haute tension - Hochspannungs-Schaltgeräte
Partie 209: Raccordement de câbles und -Schaltanlagen -
pour appareillage sous enveloppe Teil 209: Kabelanschlüsse für gasisolierte
métallique à isolation gazeuse de tension metallgekapselte Schaltanlagen
assignée supérieure à 52 kV - für Bemessungsspannungen über 52 kV -
Câbles remplis d'un fluide Kabel mit fluidgefüllter
ou à isolation extrudée - und extrudierter Isolierung -
Extrémité de câble sèche Fluidgefüllte und feststoffisolierte
ou remplie d'un fluide
Kabelendverschlüsse
(CEI 62271-209:2007) (IEC 62271-209:2007)
This European Standard was approved by CENELEC on 2007-10-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62271-209:2007 E
---------------------- Page: 2 ----------------------
EN 62271-209:2007 – 2 –
Foreword
The text of document 17C/405/FDIS, future edition 1 of IEC 62271-209, prepared by SC 17C,
High-voltage switchgear and controlgear assemblies, of IEC TC 17, Switchgear and controlgear, was
submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62271-209 on
2007-10-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2008-07-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-10-01
Annexes ZA and ZB have been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 62271-209:2007 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 3 ----------------------
– 3 – EN 62271-209:2007
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
1)
IEC 60038 (mod) 1983 IEC standard voltages HD 472 S1 1989
A1 1994 + corr. February 2002
A2 1997
IEC 60141 Series Tests on oil-filled and gas-pressure cables – –
and their accessories
IEC 60141-1 1993 Tests on oil-filled and gas-pressure cables – –
and their accessories -
Part 1: Oil-filled, paper- insulated, metal-
shealthed cables and accessories for
alternating voltages up to and including
400 kV
IEC 60141-2 1963 Tests on oil-filled and gas-pressure cables – –
and their accessories -
Part 2: Internal gas-pressure cables and
accessories for alternating voltages up to
275 kV
IEC 60694 1996 Common specifications for high-voltage EN 60694 1996
switchgear and controlgear standards + corr. May 1999
IEC 60840 2004 Power cables with extruded insulation – –
and their accessories for rated voltages
above 30 kV (U = 36 kV) up to 150 kV
m
(U = 170 kV) - Test methods and
m
requirements
IEC 62067 2001 Power cables with extruded insulation – –
A1 2006 and their accessories for rated voltages
above 150 kV (U = 170 kV) up to 500 kV
m
(U = 550 kV) - Test methods and
m
requirements
IEC 62271-203 2003 High-voltage switchgear and controlgear - EN 62271-203 2004
Part 203: Gas-insulated metal-enclosed
switchgear for rated voltages above 52 kV
CIGRE WG 23-10 1993 Earthing of GIS - An Application Guide – –
Report,
ELECTRA 151
1)
The title of HD 472 S1 is: Nominal voltages for low voltage public electricity supply systems.
---------------------- Page: 4 ----------------------
EN 62271-209:2007 – 4 –
Publication Year Title EN/HD Year
CIGRE Brochure 89, 1995 Accessories for HV Extruded Cables - – –
WG 21.06 Chapter 2.1.5: Directly Immersed Metal
Enclosed GIS Termination
---------------------- Page: 5 ----------------------
– 5 – EN 62271-209:2007
Annex ZB
(informative)
A-deviations
A-deviation: National deviation due to regulations, the alteration of which is for the time being outside the
competence of the CENELEC national member.
This European Standard does not fall under any Directive of the EC.
In the relevant CENELEC countries these A-deviations are valid instead of the provisions of the European
Standard until they have been removed.
Clause Deviation
1 Italy
(DM 1 December 1980 and DM 10 September 1981 published in Gazzetta Ufficiale no. 285
dated 16.10.1981)
For insulation-enclosed switchgear and controlgear containing gas-filled compartments, the
design pressure is limited to a maximum of 0,5 bar (gauge) and the volume is limited to a
3
maximum of 2 m . Gas filled compartments having a design pressure exceeding 0,5 bar
3
(gauge) or a volume exceeding 2 m shall be designed according to the Italian pressure
vessel code for electrical switchgear.
__________
---------------------- Page: 6 ----------------------
IEC 62271-209
Edition 1.0 2007-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
High-voltage switchgear and controlgear –
Part 209: Cable connections for gas-insulated metal-enclosed switchgear for
rated voltages above 52 kV – Fluid-filled and extruded insulation cables –
Fluid-filled and dry-type cable-terminations
Appareillage à haute tension –
Partie 209: Raccordement de câbles pour appareillage sous enveloppe
métallique à isolation gazeuse de tension assignée supérieure à 52 kV –
Câbles remplis d’un fluide ou à isolation extrudée – Extrémité de câble sèche
ou remplie d'un fluide
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
P
CODE PRIX
ICS 29.130.10 ISBN 2-8318-9242-2
---------------------- Page: 7 ----------------------
– 2 – 62271-209 © IEC:2007
CONTENTS
FOREWORD.3
1 Scope.5
2 Normative references .5
3 Terms and definitions .6
4 Limits of supply .7
4.1 General .7
4.2 Over-voltage protection .7
5 Rating .7
5.1 General .7
5.2 Rated voltage.7
5.3 Rated insulation level .8
5.4 Rated normal current and temperature rise.8
5.5 Rated short-time and peak withstand currents and rated duration of short
circuit .8
5.6 Rated filling pressure of insulating gas in the cable connection enclosure .8
6 Design and construction requirements.9
6.1 Pressure withstand requirements.9
6.2 Mechanical forces on cable-terminations .9
7 Standard dimensions .10
7.1 Fluid-filled cable-terminations.10
7.2 Dry-type cable-terminations.10
7.3 Three-phase cable-termination enclosure.10
8 Tests .10
8.1 General .10
8.2 Dielectric type tests of cable-terminations .11
8.2.1 General .11
8.2.2 Dielectric type test of cable-terminations in a single phase enclosure .11
8.2.3 Dielectric type test of cable-termination in a three phase enclosure .11
8.3 Tests after cable system installation.11
9 Information to be given with enquiries, tenders and orders .12
10 Rules for transport, storage, erection, operation and maintenance .12
Figure 1 – Operating pressure of the gas insulation in the cable connection enclosure .9
Figure 2 – Fluid-filled cable connection assembly – Typical arrangement.13
Figure 3 – Fluid-filled cable connection – Assembly dimensions .14
Figure 4 – Dry-type cable connection assembly – Typical arrangement.15
Figure 5 – Dry-type cable connection assembly – Assembly dimensions.16
---------------------- Page: 8 ----------------------
62271-209 © IEC:2007 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR –
Part 209: Cable connections for gas-insulated metal-enclosed
switchgear for rated voltages above 52 kV –
Fluid-filled and extruded insulation cables –
Fluid-filled and dry-type cable-terminations
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62271-209 has been prepared by subcommittee 17C: High-voltage
switchgear and controlgear assemblies, of IEC technical committee 17: Switchgear and
controlgear.
This first edition of IEC 62271-209 cancels and replaces the second edition of IEC/TS 60859
and constitutes a technical revision. The changes from IEC/TS 60859 are as follows:
– the minimum voltage rating was changed from “72,5 kV” to ”above 52 kV”;
– the current rating was increased to 3150 A;
---------------------- Page: 9 ----------------------
– 4 – 62271-209 © IEC:2007
– simplifications and modifications of the dimension tables in Figure 2 and Figure 4 such as
diameters for 123 kV to 170 kV have been adopted in order to accommodate larger cable
cross-sections; new dimensions accept old terminations, new terminations may not meet
old GIS standards;
– the following dimensions have been deleted: l1, l3 as well as note 3 on Figure 4;
– in Figure 4, new dimensions have been adopted for the voltage range from 245 kV to
300 kV, interchangeability for 245 kV to 300 kV is not maintained due to reduction in GIS
cable termination housing;
– the lengths l7 and l8 have been modified;
– changes in the text in relation to minimum functional pressure for insulation p (Table 1
me
has been removed);
– the limit of 170 kV for 3-phase application was deleted (Subclause 5.2);
– Figure 5 was deleted.
The text of this standard is based on the following documents:
FDIS Report on voting
17C/405/FDIS 17C/412/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all the parts in the IEC 62271 series, under the general title High-voltage switchgear
and controlgear, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 10 ----------------------
62271-209 © IEC:2007 – 5 –
HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR –
Part 209: Cable connections for gas-insulated metal-enclosed
switchgear for rated voltages above 52 kV –
Fluid-filled and extruded insulation cables –
Fluid-filled and dry-type cable-terminations
1 Scope
This standard covers the connection assembly of fluid-filled and extruded cables to gas-
insulated metal enclosed switchgear (GIS), in single- or three-phase arrangements where the
cable-terminations are fluid-filled or dry type and there is a separating insulating barrier
between the cable insulation and the gas insulation of the switchgear.
The purpose of this standard is to establish electrical and mechanical interchangeability
between cable-terminations and the gas-insulated metal-enclosed switchgear and to
determine the limits of supply. It complements and amends, if necessary, the relevant IEC
standards. For the purpose of this standard the term "switchgear" is used for "gas-insulated
metal enclosed switchgear".
It does not cover directly immersed cable terminations, as described in CIGRE brochure 89.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
1
IEC 60038:1983, IEC standard voltages
Amendment 1 (1994)
Amendment 2 (1997)
IEC 60141 (all parts), Tests on oil-filled and gas-pressure cables and their accessories
IEC 60141-1:1993, Tests on oil-filled and gas-pressure cables and their accessories – Part 1:
Oil-filled
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.