SIST ISO 8138:1998

Hydraulic fluid power -- Single rod cylinders, 16 MPa (160 bar) compact series -- Port dimensions

Transmissions hydrauliques -- Vérins 16 MPa (160 bar) série compacte à simple tige -- Dimensions des orifices

Fluidna tehnika - Hidravlika - Valji z enostransko batnico kompaktne vrste 160 barov (16 MPa) - Mere priključnih odprtin

General Information

• Status: Withdrawn
• Publication Date: 30-Nov-1998
• Withdrawal Date: 17-Dec-2013
• ICS: 23.100.20 - Cylinders
• Technical Committee: IHPV - Hydraulics and pneumatics
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 17-Dec-2013
• Due Date: 09-Jan-2014
• Completion Date: 18-Dec-2013
• Ref Project: ISO 8138:1998 - Hydraulic fluid power — Single rod cylinders, 16 MPa (160 bar) compact series — Port dimensions

Relations

• Revised: ISO 8138:1986 - Hydraulic fluid power — Single rod cylinders, 160 bar (16 MPa) compact series — Port dimensions
• Effective Date: 18-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 8138
Second edition
1998-06-15
Hydraulic fluid power — Single rod
cylinders, 16 MPa (160 bar) compact
series — Port dimensions
Transmissions hydrauliques — Vérins 16 MPa (160 bar) série compacte
à simple tige — Dimensions des orifices
A
Reference number
ISO 8138:1998(E)

---------------------- Page: 1 ----------------------
ISO 8138:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 8138 was prepared by ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders.
This second edition cancels and replaces the first edition (ISO 8138:1986) which has been technically revised.
©  ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
Printed in Switzerland
ii

---------------------- Page: 2 ----------------------
©
ISO ISO 8138:1998(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an
enclosed circuit.
One component of such systems is the fluid power cylinder. This is a device which converts power into linear
mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod, operating within a
cylindrical bore.
iii

---------------------- Page: 3 ----------------------
©
INTERNATIONAL STANDARD  ISO ISO 8138:1998(E)
Hydraulic fluid power — Single rod cylinders, 16 MPa
(160 bar) compact series — Port dimensions
1 Scope
1) 2)
This International Standard establishes port dimensions for 16 MPa (160 bar ) compact series cylinders as
required for interchangeability of commonly used hydraulic cylinders.
NOTE —  This International Standard allows manufacturers of hydraulic equipment, freedom in design of metric cylinders; it
does not restrict technical development but provides basic guidelines.
The compact series dimensions are most applicable to square head cylinders.
This International Standard will be incorporated into the next edition of ISO 6020-2.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain
registers of currently valid International Standards.
3)
ISO 1179-1:— , Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with
elastomeric or metal-to-metal sealing — Part 1: Threaded ports.
ISO 3320:1987, Fluid power systems and components — Cylinder bores and
...

SLOVENSKI STANDARD
SIST ISO 8138:1998
01-december-1998
)OXLGQDWHKQLND+LGUDYOLND9DOML]HQRVWUDQVNREDWQLFRNRPSDNWQHYUVWH
EDURY03D0HUHSULNOMXþQLKRGSUWLQ
Hydraulic fluid power -- Single rod cylinders, 16 MPa (160 bar) compact series -- Port
dimensions
Transmissions hydrauliques -- Vérins 16 MPa (160 bar) série compacte à simple tige --
Dimensions des orifices
Ta slovenski standard je istoveten z: ISO 8138:1998
ICS:
23.100.20 +LGUDYOLþQLYDOML Cylinders
SIST ISO 8138:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 8138:1998

---------------------- Page: 2 ----------------------

SIST ISO 8138:1998
INTERNATIONAL ISO
STANDARD 8138
Second edition
1998-06-15
Hydraulic fluid power — Single rod
cylinders, 16 MPa (160 bar) compact
series — Port dimensions
Transmissions hydrauliques — Vérins 16 MPa (160 bar) série compacte
à simple tige — Dimensions des orifices
A
Reference number
ISO 8138:1998(E)

---------------------- Page: 3 ----------------------

SIST ISO 8138:1998
ISO 8138:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 8138 was prepared by ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders.
This second edition cancels and replaces the first edition (ISO 8138:1986) which has been technically revised.
©  ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
Printed in Switzerland
ii

---------------------- Page: 4 ----------------------

SIST ISO 8138:1998
©
ISO ISO 8138:1998(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an
enclosed circuit.
One component of such systems is the fluid power cylinder. This is a device which converts power into linear
mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod, operating within a
cylindrical bore.
iii

---------------------- Page: 5 ----------------------

SIST ISO 8138:1998

---------------------- Page: 6 ----------------------

SIST ISO 8138:1998
©
INTERNATIONAL STANDARD  ISO ISO 8138:1998(E)
Hydraulic fluid power — Single rod cylinders, 16 MPa
(160 bar) compact series — Port dimensions
1 Scope
1) 2)
This International Standard establishes port dimensions for 16 MPa (160 bar ) compact series cylinders as
required for interchangeability of commonly used hydraulic cylinders.
NOTE —  This International Standard allows manufacturers of hydraulic equipment, freedom in design of metric cylinders; it
does not restrict technical development but provides basic guidelines.
The compact series dimensions are most applicable to square head cylinders.
This International Standard will be incorporated into the next edition of ISO 6020-2.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, th
...

NORME ISO
INTERNATIONALE 8138
Deuxième édition
1998-06-15
Transmissions hydrauliques — Vérins
16 MPa (160 bar) série compacte à simple
tige — Dimensions des orifices
Hydraulic fluid power — Single rod cylinders, 16 MPa (160 bar) compact
series — Port dimensions
A
Numéro de référence
ISO 8138:1998(F)

---------------------- Page: 1 ----------------------
ISO 8138:1998(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec l'ISO, participent également aux travaux. L'ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités
membres votants.
La Norme internationale ISO 8138 a été élaborée par le comité technique ISO/TC 131, Transmissions hydrauliques
et pneumatiques, sous-comité SC 3, Vérins.
Cette deuxième édition annule et remplace la première édition (ISO 8138:1986), dont elle constitue une révision
technique.
©  ISO 1998
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publi-
cation ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun pro-
cédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord
écrit de l'éditeur.
Organisation internationale de normalisation
Case postale 56 • CH-1211 Genève 20 • Suisse
Internet [e-mail]
Imprimé en Suisse
ii

---------------------- Page: 2 ----------------------
©
ISO ISO 8138:1998(F)
Introduction
Dans les systèmes de transmissions hydrauliques, l'énergie est transmise et commandée par l’intermédiaire d’un
liquide sous pression circulant en circuit fermé.
L'un des composants de tels systèmes est le vérin hydraulique. C'est un appareil qui transforme l'énergie du fluide
en énergie mécanique agissant linéairement. Il est constitué d'un élément mobile, par exemple un piston et une tige
de piston, se déplaçant à l'intérieur d'un alésage cylindrique.
iii

---------------------- Page: 3 ----------------------
©
NORME INTERNATIONALE  ISO ISO 8138:1998(F)
Transmissions hydrauliques — Vérins 16 MPa (160 bar)
série compacte à simple tige — Dimensions des orifices
1 Domaine d’application
1) 2)
La présente Norme internationale prescrit les dimensions des orifices des vérins 16 MPa (160 bar ) série
compacte à simple tige permettant d´assurer l´interchangeabilité des vérins hydrauliques d´usage courant.
NOTE —  La présente Norme internationale laisse aux fabricants d´équipements hydrauliques toute latitude quant à la
conception des vérins de la série métrique; elle ne restreint pas le progrès technique, tout en fixant des orientations générales
de base.
Les dimensions de la série compacte ne sont pas applicables aux vérins à tête carrée.
La présente Norme internationale sera incorporée dans la prochaine édition de l´ISO 6020-2.
2 Références normatives
Les normes suivantes contiennent des dispositions qui, par suite de la référence qui en est faite, constituent des
dispositions valables pour la présente Norme internationale. Au moment de la publication, les éditions indiquées
étaient en vigueur. Toute norme est sujette à révision et les parties prenantes des accords fondés sur la présente
Norme internationale sont invitées à rechercher la possibilité d'appliquer les éditions les plus récentes des normes
indiquées ci-après. Les membres de la CEI et de l'ISO possèdent le registre des Normes internationales en vigueur
à un moment donné.
3)
ISO 1179-1:— , Raccordements pour transmissions hydrauliques et pneumatiques et applications générales —
Orifices et éléments mâles à filetage ISO 228-1 et joint en élastomère ou étanchéité métal sur métal — Partie 1:
Orifices filetés.
ISO 3320:1987, Transmissions hydrauliques et pneumatiques — Alésages des vérins et diamètres des tiges de
piston — Série métrique.
ISO 5598:1985, Tran
...