SIST ISO 8135:2000

Hydraulic fluid power -- Single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series -- Tolerances

Transmissions hydrauliques -- Vérins 16 MPa (160 bar) série moyenne et 25 MPa (250 bar), à simple tige -- Tolérances

Fluidna tehnika - Hidravlika - Valji z enostransko batnico srednje vrste 16 MPa (160 bar) in vrste 25 MPa (250 bar) - Tolerance

General Information

• Status: Withdrawn
• Publication Date: 31-Aug-2000
• Withdrawal Date: 17-Dec-2013
• ICS: 23.100.20 - Cylinders
• Technical Committee: IHPV - Hydraulics and pneumatics
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 17-Dec-2013
• Due Date: 09-Jan-2014
• Completion Date: 18-Dec-2013
• Ref Project: ISO 8135:1999 - Hydraulic fluid power — Single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series — Tolerances

Relations

• Revised: ISO 6020-1:2007 - Hydraulic fluid power — Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series — Part 1: Medium series
• Effective Date: 18-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 8135
Second edition
1999-03-01
Hydraulic fluid power — Single rod
cylinders, 16 MPa (160 bar) medium
and 25 MPa (250 bar) series — Tolerances
Transmissions hydrauliques — Vérins 16 MPa (160 bar) série moyenne
et 25 MPa (250 bar), à simple tige — Tolérances
A
Reference number
ISO 8135:1999(E)

---------------------- Page: 1 ----------------------
ISO 8135:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 8135 was prepared by Technical Committee ISO/TC 131, Fluid power systems,
Subcommittee SC 3, Cylinders.
This second edition cancels and replaces the first edition (ISO 8135:1986), which has been technically revised.
Annex A of this International Standard is for information only.
©  ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
Printed in Switzerland
ii

---------------------- Page: 2 ----------------------
© ISO
ISO 8135:1999(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an
enclosed circuit.
One component of such systems is the fluid power cylinder. This is a device which converts power into linear
mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod, operating within a
cylindrical bore.
iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD  © ISO ISO 8135:1999(E)
Hydraulic fluid power — Single rod cylinders, 16 MPa (160 bar)
medium and 25 MPa (250 bar) series — Tolerances
1 Scope
1)
This International Standard specifies dimensional tolerances for 16 MPa [160 bar ] medium and 25 MPa (250 bar)
series cylinders in accordance with ISO 6020-1 and ISO 6022, as required for interchangeability of commonly used
hydraulic cylinders
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain
registers of currently valid International Standards.
ISO 4393:1978, Fluid power systems and components — Cylinders — Basic series of piston strokes.
ISO 5598:1985, Fluid power systems and components — Vocabulary.
ISO 6020-1:1998, Hydraulic fluid power — Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series —
Part 1: Medium series.
ISO 6022:1981, Hydraulic fluid power — Single rod cylinders — Mounting dimensions — 250 bar (25 000 kPa)
series.
ISO 6099:1985, Fluid power systems and components — Cylinders — Identification code for mounting dimensions
...

SLOVENSKI STANDARD
SIST ISO 8135:2000
01-september-2000
Fluidna tehnika - Hidravlika - Valji z enostransko batnico srednje vrste 16 MPa (160
bar) in vrste 25 MPa (250 bar) - Tolerance
Hydraulic fluid power -- Single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250
bar) series -- Tolerances
Transmissions hydrauliques -- Vérins 16 MPa (160 bar) série moyenne et 25 MPa (250
bar), à simple tige -- Tolérances
Ta slovenski standard je istoveten z: ISO 8135:1999
ICS:
23.100.20 +LGUDYOLþQLYDOML Cylinders
SIST ISO 8135:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 8135:2000

---------------------- Page: 2 ----------------------

SIST ISO 8135:2000
INTERNATIONAL ISO
STANDARD 8135
Second edition
1999-03-01
Hydraulic fluid power — Single rod
cylinders, 16 MPa (160 bar) medium
and 25 MPa (250 bar) series — Tolerances
Transmissions hydrauliques — Vérins 16 MPa (160 bar) série moyenne
et 25 MPa (250 bar), à simple tige — Tolérances
A
Reference number
ISO 8135:1999(E)

---------------------- Page: 3 ----------------------

SIST ISO 8135:2000
ISO 8135:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 8135 was prepared by Technical Committee ISO/TC 131, Fluid power systems,
Subcommittee SC 3, Cylinders.
This second edition cancels and replaces the first edition (ISO 8135:1986), which has been technically revised.
Annex A of this International Standard is for information only.
©  ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
Printed in Switzerland
ii

---------------------- Page: 4 ----------------------

SIST ISO 8135:2000
© ISO
ISO 8135:1999(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an
enclosed circuit.
One component of such systems is the fluid power cylinder. This is a device which converts power into linear
mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod, operating within a
cylindrical bore.
iii

---------------------- Page: 5 ----------------------

SIST ISO 8135:2000

---------------------- Page: 6 ----------------------

SIST ISO 8135:2000
INTERNATIONAL STANDARD  © ISO ISO 8135:1999(E)
Hydraulic fluid power — Single rod cylinders, 16 MPa (160 bar)
medium and 25 MPa (250 bar) series — Tolerances
1 Scope
1)
This International Standard specifies dimensional tolerances for 16 MPa [160 bar ] medium and 25 MPa (250 bar)
series cylinders in accordance with ISO 6020-1 and ISO 6022, as required for interchangeability of commonly used
hydraulic cylinders
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain
registers of currently valid International Standards.
ISO 4393:1978, Fluid power sy
...

NORME ISO
INTERNATIONALE 8135
Deuxième édition
1999-03-01
Transmissions hydrauliques — Vérins
16 MPa (160 bar) série moyenne
et 25 MPa (250 bar), à simple tige —
Tolérances
Hydraulic fluid power — Single rod cylinders, 16 MPa (160 bar) medium
and 25 MPa (250 bar) series — Tolerances
Numéro de référence
A
ISO 8135:1999(F)

---------------------- Page: 1 ----------------------
ISO 8135:1999(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec l'ISO, participent également aux travaux. L'ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités
membres votants.
La Norme internationale ISO 8135 a été élaborée par l'ISO/TC 131, Transmissions hydrauliques et pneumatiques,
sous-comité SC 3, Vérins.
Cette deuxième édition annule et remplace la première édition (ISO 8135:1886), dont elle constitue une révision
technique.
L'annexe A de la présente Norme internationale est donnée uniquement à titre d'information.
©  ISO 1999
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque
forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l'éditeur.
Organisation internationale de normalisation
Case postale 56 • CH-1211 Genève 20 • Suisse
Internet [e-mail]
Imprimé en Suisse
ii

---------------------- Page: 2 ----------------------
© ISO
ISO 8135:1999(F)
Introduction
Dans les systèmes de transmissions hydrauliques, l'énergie est transmise et commandée par l’intermédiaire d’un
liquide sous pression circulant en circuit fermé.
L'un des composants de tels systèmes est le vérin hydraulique. C'est un appareil qui transforme l'énergie du fluide
en énergie mécanique agissant linéairement. Il est constitué d'un élément mobile, par exemple un piston et une tige
de piston, se déplaçant à l'intérieur d'un alésage cylindrique.
iii

---------------------- Page: 3 ----------------------
©
NORME INTERNATIONALE  ISO ISO 8135:1999(F)
Transmissions hydrauliques — Vérins 16 MPa (160 bar) série
moyenne et 25 MPa (250 bar), à simple tige — Tolérances
1 Domaine d’application
La présente Norme internationale spécifie les tolérances dimensionnelles pour les vérins hydrauliques 16 MPa
1)
@160 bar # série moyenne et 25 MPa (250 bar) conformes à l'ISO 6020-1 et à l'ISO 6022, permettant d'assurer
l'interchangeabilité des vérins hydrauliques d'usage courant.
2 Références normatives
Les normes suivantes contiennent des dispositions qui, par suite de la référence qui en est faite, constituent des
dispositions valables pour la présente Norme internationale. Au moment de la publication, les éditions indiquées
étaient en vigueur. Toute norme est sujette à révision et les parties prenantes des accords fondés sur la présente
Norme internationale sont invitées à rechercher la possibilité d'appliquer les éditions les plus récentes des normes
indiquées ci-après. Les membres de la CEI et de l'ISO possèdent le registre des Normes internationales en vigueur
à un moment donné.
ISO 4393:1978, Transmissions hydrauliques et pneumatiques — Vérins — Série de base de courses de piston.
ISO 5598:1985, Transmissions hydrauliques et pneumatiques — Vocabulaire.
ISO 6020-1:1998, Transmissions hydrauliques — Dimensions d'interchangeabilité des vérins 16 MPa (160 bar) à
simple tige — Série moyenne
ISO 6022:1981, Transmissions hydrauliques — Vérins 250 bar (25 000 kPa) à simple tige — Dimensions
d'interchangeabilité.
ISO 6099:1985, Transmissions hydrauliques et pneumatiques — Vérins — Code d'identification des dimensions de
montage et des modes de fixation.
3 Définitions
Pour les besoins de la présente Norme internationale, les définitions
...