SIST EN 12312-20:2005
(Main)Aircraft ground support equipment - Specific requirements - Part 20: Electrical ground power units
Aircraft ground support equipment - Specific requirements - Part 20: Electrical ground power units
This European Standard specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of ground power equipment, when carried out in accordance with the specifications given by the manufacturer or his authorised representative. It also takes into account some performance requirements recognised as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and service companies.
This European Standard applies to:
- ground power units either self-propelled or towable (Examples see Annex A);
- ground power equipment when mounted on other GSE;
- ground power accessories intended for ground power equipment (including accessories for fixed equipment).
This European Standard does not apply to:
- the electrical characteristics of the supply, the type of power supply system and related measures against contact;
- any electrical supply system not intended for aircraft use;
- the on-board electrical system of the aircraft.
This European Standard does not establish requirements for noise and vibration.
Noise and vibration are dealt with respectively in EN 1915 4 and EN 1915 3.
This European Standard does not deal with hazards in respect to a standard automotive chassis and from other vehicles on the apron.
This Part of EN 12312 is not applicable to ground power equipment which is manufactured before the date of publication of this European Standard by CEN.
Luftfahrt-Bodengeräte - Besondere Anforderungen - Teil 20: Ausrüstung zur Bodenstromversorgung
Diese Europäische Norm legt die technischen Anforderungen zur Minimierung der in Abschnitt 4 aufgelisteten Gefährdungen fest, die bei Inbetriebnahme, Betrieb und Wartung von Ausrüstungen zur Bodenstromversorgung auftreten können, wenn diese in Übereinstimmung mit den Anweisungen des Herstellers oder seines Beauftragten ausgeführt werden. Sie berücksichtigt auch einige Anforderungen, die von offiziellen Stellen, Luftfahrzeug- und Bodengeräteherstellern sowie Luftverkehrs- und Wartungsgesellschaften als wesentlich erachtet wurden.
Diese Norm gilt für:
mobile Ausrüstungen zur Bodenstromversorgung oder Bodenstromzubehör, selbstfahrend oder schleppbar, für die Einspeisung von elektrischer Energie in Luftfahrzeuge (Beispiele siehe Anhang A);
bewegliche Teile, die an fest installierten Systemen zur Bodenstromversorgung oder an mobilen/beweglichen Ausrüstungen zur Bodenstromversorgung auf Luftfahrt Bodengeräten montiert sind, z. B. Schleppern.
Diese Norm gilt nicht für:
elektrische Charakteristika und Daten des Versorgungssystems;
elektrische Versorgungssysteme, die nicht für Luftfahrzeuge bestimmt sind;
nicht bewegliche Teile von Ausrüstungen zur Bodenstromversorgung von Luftfahrzeugen;
elektrische Systeme an Bord von Luftfahrzeugen;
pneumatische Systeme.
Diese Norm enthält keine Festlegungen für Gefährdungen, die durch Lärm und Vibration verursacht werden.
Dieser Teil von EN 12312 gilt nicht für Ausrüstungen zur Bodenstromversorgung, die vor der Veröffentlichung dieser Norm durch CEN hergestellt wurden.
Matériel au sol pour aéronefs - Exigences particulieres - Partie 20 : Matériel d'alimentation électrique au sol
La présente Norme européenne spécifie les exigences techniques pour minimiser les dangers listés
a l'Article 4 qui pourraient apparaître lors de la mise en service, de l'exploitation et de la maintenance de
matériels d'alimentation électrique au sol réalisés conformément aux spécifications émises par le constructeur
ou son représentant autorisé. Il prend également en compte certaines exigences reconnues essentielles par
les autorités, les fabricants d'aéronefs et de matériels de service au sol (GSE), ainsi que les compagnies
aériennes et organismes d'assistance.
La présente Norme européenne s'applique aux :
.matériels d'alimentation électrique au sol qu'ils soient auto-tractés ou tractables (voir exemples
en Annexe A) ;
.matériels d'alimentation électrique au sol montés sur d'autres GSE ;
.accessoires destinés aux matériels d'alimentation électrique au sol (y compris les accessoires pour
matériels fixes).
La présente Norme européenne ne s'applique pas aux :
.caractéristiques électriques de l'alimentation, types de systeme d'alimentation et mesures associées
contre les contacts ;
.systemes d'alimentation électrique non prévus pour emploi avec des aéronefs ;
.systemes électriques a bord des aéronefs.
La présente Norme européenne ne spécifie pas d'exigences pour le bruit et les vibrations.
Le bruit et les vibrations sont traités respectivement dans l'EN 1915-4 et l'EN 1915-3.
La présente Norme européenne ne traite pas des dangers en relation avec un châssis automoteur standard et
avec le trafic sur l'aire de stationnement.
La présente Partie de l'EN 12312 ne s'applique pas aux matériels d'alimentation
Podporna oprema na tleh za letalski promet - Posebne zahteve – 20. del: Oskrba z električno energijo
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12312-20:2005
01-december-2005
3RGSRUQDRSUHPDQDWOHK]DOHWDOVNLSURPHW3RVHEQH]DKWHYH±GHO 2VNUED]
HOHNWULþQRHQHUJLMR
Aircraft ground support equipment - Specific requirements - Part 20: Electrical ground
power units
Luftfahrt-Bodengeräte - Besondere Anforderungen - Teil 20: Ausrüstung zur
Bodenstromversorgung
Matériel au sol pour aéronefs - Exigences particulieres - Partie 20 : Matériel
d'alimentation électrique au sol
Ta slovenski standard je istoveten z: EN 12312-20:2005
ICS:
49.100 Oprema za servis in Ground service and
vzdrževanje na tleh maintenance equipment
SIST EN 12312-20:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 12312-20
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2005
ICS 49.100
English Version
Aircraft ground support equipment - Specific requirements - Part
20: Electrical ground power units
Matériel au sol pour aéronefs - Exigences particulières - Luftfahrt-Bodengeräte - Besondere Anforderungen - Teil
Partie 20 : Matériel d'alimentation électrique au sol 20: Ausrüstung zur Bodenstromversorgung
This European Standard was approved by CEN on 1 August 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12312-20:2005: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 12312-20:2005 (E)
Contents
page
Foreword .3
Introduction.4
1 Scope .5
2 Normative references .5
3 Terms and definitions.6
4 List of hazards.6
5 Safety requirements and/or measures .6
6 Information for use .8
7 Verification of requirements.9
Annex A (informative) Examples of ground power equipment .10
Annex B (normative) List of hazards in addition to those of EN 1915-1.12
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC, amended by Directive 98/79/EC.14
Bibliography.15
2
---------------------- Page: 3 ----------------------
EN 12312-20:2005 (E)
Foreword
This European Standard (EN 12312-20:2005) has been prepared by Technical Committee CEN/TC 274 “Aircraft
ground support equipment”, the secretariat is of which held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by March 2006, and conflicting national standards shall be withdrawn at the latest by
March 2006.
This European Standard has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association and supports essential requirements of EU Directive(s).
For relationship with EU Directives, see informative Annex ZA, which is an integral part of this document.
The Parts of EN 12312 — Aircraft ground support equipment — Specific requirements — are:
Part 1: Passenger stairs
Part 2: Catering vehicles
Part 3: Conveyor belt vehicles
Part 4: Passenger boarding bridges
Part 5: Aircraft fuelling equipment
Part 6: Deicers and deicing/antiicing equipment
Part 7: Aircraft movement equipment
Part 8: Maintenance stairs and platforms
Part 9: Container/Pallet loaders
Part 10: Container/Pallet transfer transporters
Part 11: Container/Pallet dollies and loose load trailers
Part 12: Potable water service equipment
Part 13: Lavatory service equipment
Part 14: Disabled/Incapacitated passenger boarding equipment
Part 15: Baggage and equipment tractors
Part 16: Air start equipment
Part 17: Air conditioning equipment
Part 18: Nitrogen or Oxygen units
Part 19: Aircraft jacks, axle jacks and hydraulic tail stanchions
Part 20: Electrical ground power units
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
3
---------------------- Page: 4 ----------------------
EN 12312-20:2005 (E)
Introduction
This European Standard specifies health and safety requirements, as well as some functional and performance
requirements for ground power equipment intended for the electrical supply for aircraft to be used on all aircraft
types commonly in service in civil air transport.
The minimum essential criteria are considered to be of primary importance in providing safe, serviceable, economical,
and practical ground power equipment. Deviations from the recommended criteria should occur only after careful
consideration, extensive testing, risk assessment and thorough service evaluation have shown alternative methods or
conditions to be satisfactory.
This European Standard is a Type C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this European Standard.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines that
have been designed and built according to the provisions of this type C standard.
4
---------------------- Page: 5 ----------------------
EN 12312-20:2005 (E)
1 Scope
This European Standard specifies the technical requirements to minimise the hazards listed in Clause 4 which can
arise during the commissioning, operation and maintenance of ground power equipment, when carried out in
accordance with the specifications given by the manufacturer or his authorised representative. It also takes into
account some performance requirements recognised as essential by authorities, aircraft and ground support
equipment (GSE) manufacturers as well as airlines and service companies.
This European Standard applies to:
ground power units either self-propelled or towable (Examples see Annex A);
ground power equipment when mounted on other GSE;
ground power accessories intended for ground power equipment (including accessories for fixed equipment).
This European Standard does not apply to:
the electrical characteristics of the supply, the type of power supply system and related measures against
contact;
any electrical supply system not intended for aircraft use;
the on-board electrical system of the aircraft.
This European Standard does not establish requirements for noise and vibration.
Noise and vibration are dealt with respectively in EN 1915-4 and EN 1915-3.
This European Standard does not deal with hazards in respect to a standard automotive chassis and from other
vehicles on the apron.
This Part of EN 12312 is not applicable to ground power equipment which is manufactured before the date of
publication of this European Standard by CEN.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN 418:1992, Safety of machinery — Emergency stop equipment, functional aspects — Principles for design
EN 1050:1996, Safety of machinery — Principles for risk assessment
EN 1175-1, Safety of industrial trucks - Electrical requirements - Part 1: General requirements for battery powered
trucks
EN 1915-1:2001, Aircraft ground support equipment — General requirements — Part 1: Basic safety requirements
EN 1915-2, Aircraft ground support equipment — General requirements — Part 2: Stability and strength
requirements, calculations and test methods
EN 12601, Reciprocating internal combustion engine driven generating sets — Safety
EN 60204-1:1997, Safety of machinery — Electrical equipment of machines — Part 1: General requirements
(IEC 60204-1:1997)
5
---------------------- Page: 6 ----------------------
EN 12312-20:2005 (E)
EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology (ISO 12100-1:2003)
EN ISO 12100-2:2003, Safety of machinery - Basic concepts, general principles for design - Part 2: Technical
principles (ISO 12100-2:2003)
ISO 461-1 Aircraft — Connectors for ground electrical supplies — Part 1: Design performance and test equipment
ISO 461-2, Aircraft — Connectors for ground electrical supplies — Part 2: Dimensions
3 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN ISO 12100-1:2003 and
EN 1915-1:2001 and the following apply.
3.1
ground power equipment
system used to deliver external electrical power to the aircraft, designed to substitute the on-board electrical power
supply
3.2
ground power unit (GPU)
mobile ground power equipment
NOTE This term includes units mounted on other mobile GSE.
3.3
ground power accessory
components of ground power equipment: cable handling systems, cables, connectors
4 List of hazards
The list of risks and hazards (see Annex B) is based on EN 10
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.