SIST EN ISO 7823-3:2004
(Main)Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 3: Continuous cast sheets (ISO 7823-3:2003)
Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 3: Continuous cast sheets (ISO 7823-3:2003)
Kunststoffe - Tafeln aus Polymethylmethacrylat - Typen, Maße und Eigenschaften - Teil 3: Endlosprodukte (ISO 7823-3:2003)
Plastiques - Plaques en poly(méthacrylate de méthyle) - Types, dimensions et caractéristiques - Partie 3: Plaques coulées continues (ISO 7823-3:2003)
Polimerni materiali - Plošče iz polimetilmetakrilata - Vrste, mere in značilnosti - 3. del: Kontinuirno lite plošče (ISO 7823-3:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 7823-3:2004
01-oktober-2004
3ROLPHUQLPDWHULDOL3ORãþHL]SROLPHWLOPHWDNULODWD9UVWHPHUHLQ]QDþLOQRVWL
GHO .RQWLQXLUQROLWHSORãþH ,62
Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics -
Part 3: Continuous cast sheets (ISO 7823-3:2003)
Kunststoffe - Tafeln aus Polymethylmethacrylat - Typen, Maße und Eigenschaften - Teil
3: Endlosprodukte (ISO 7823-3:2003)
Plastiques - Plaques en poly(méthacrylate de méthyle) - Types, dimensions et
caractéristiques - Partie 3: Plaques coulées continues (ISO 7823-3:2003)
Ta slovenski standard je istoveten z: EN ISO 7823-3:2004
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 7823-3:2004 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 7823-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2004
ICS 83.140.10
English version
Plastics - Poly(methyl methacrylate) sheets - Types, dimensions
and characteristics - Part 3: Continuous cast sheets (ISO 7823-
3:2003)
Plastiques - Plaques en poly(méthacrylate de méthyle) -
Types, dimensions et caractéristiques - Partie 3: Plaques
coulées continues (ISO 7823-3:2003)
This European Standard was approved by CEN on 21 June 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7823-3:2004: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 7823-3:2004 (E)
Foreword
The text of ISO 7823-3:2003 has been prepared by Technical Committee ISO/TC 61 "Plastics”
of the International Organization for Standardization (ISO) and has been taken over as EN ISO
7823-3:2004 by Technical Committee CEN/TC 249 "Plastics", the secretariat of which is held by
IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2005, and conflicting national
standards shall be withdrawn at the latest by January 2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 7823-3:2003 has been approved by CEN as EN ISO 7823-3:2004 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2
---------------------- Page: 3 ----------------------
EN ISO 7823-3:2004 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 62 1999 Plastics - Determination of water EN ISO 62 1999
absorption
ISO 75-1 1993 Plastics - Determination of EN ISO 75-1 1996
temperature of deflection under load
- Part 1: General test method
ISO 75-2 1993 Plastics - Determination of EN ISO 75-2 1996
temperature of deflection under load
- Part 2: Plastics and ebonite
ISO 178 2001 Plastics - Determination of flexural EN ISO 178 2003
properties
ISO 179-1 2000 Plastics - Determination of Charpy EN ISO 179-1 2000
impact properties - Part 1: Non-
instrumented impact test
ISO 291 1997 Plastics - Standard atmospheres for EN ISO 291 1997
conditioning and testing
ISO 306 1994 Plastics - Thermoplastic materials - EN ISO 306 1996
Determination of Vicat softening
temperature (VST)
ISO 489 1999 Plastics - Determination of refractive EN ISO 489 1999
index
ISO 527-1 1996 Plastics - Determination of tensile EN ISO 527-1 1993
properties - Part 1: General
principles
3
---------------------- Page: 4 ----------------------
EN ISO 7823-3:2004 (E)
ISO 527-2 1996 Plastics - Determination of tensile EN ISO 527-2 1993
properties - Part 2: Test conditions
for moulding and extrusion plastics
ISO 877 1994 Plastics - Methods of exposure to EN ISO 877 1996
direct weathering, to weathering
using glass-filtered daylight, and to
intensified weathering by daylight
using Fresnel mirrors
ISO 2039-2 1987 Plastics - Determination of hardness EN ISO 2039-2 1999
- Part 2: Rockwell hardness
ISO 2818 1994 Plastics - Preparation of test EN ISO 2818 1996
specimens by machining
ISO 4892-2 1994 Plastics - Methods of exposure to EN ISO 4892-2 1999
laboratory light sources - Part 2:
Xenon-arc sources
ISO 13468-1 1996 Plastics - Determination of total EN ISO 13468-1 1996
luminous transmittance of
transparent materials - Part 1:
Single-beam instrument
4
---------------------- Page: 5 ----------------------
INTERNATIONAL ISO
STANDARD 7823-3
First edition
2003-07-01
Plastics — Poly(methyl methacrylate)
sheets — Types, dimensions and
characteristics —
Part 3:
Continuous cast sheets
Plastiques — Plaques en poly(méthacrylate de méthyle) — Types,
dimensions et caractéristiques —
Partie 3: Plaques coulées continues
Reference number
ISO 7823-3:2003(E)
©
ISO 2003
---------------------- Page: 6 ----------------------
ISO 7823-3:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
©
ii ISO 2003 – All rights reserved
---------------------- Page: 7 ----------------------
ISO 7823-3:2003(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Composition . 2
5 General requirements . 3
6 Test methods . 5
7 Retest and rejection . 7
Annex A (normative) Determination of dimensional change on heating (shrinkage) . 8
©
ISO 2003 – All rights reserved iii
---------------------- Page: 8 ----------------------
ISO 7823-3:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 7823-3 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
ISO 7823 consists of the following parts, under the general title Plastics — Poly(methyl methacrylate) sheets —
Types, dimensions and characteristics:
— Part 1: Cast sheets
— Part 2: Extruded sheets
— Part 3: Continuous cast sheets
©
iv ISO 2003 – All rights reserved
---------------------- Page: 9 ----------------------
INTERNATIONAL STANDARD ISO 7823-3:2003(E)
Plastics — Poly(methyl methacrylate) sheets — Types,
dimensions and characteristics —
Part 3:
Continuous cast sheets
1Scope
This part of ISO7823 specifies requirements for non-modified flat poly(methyl methacrylate) (PMMA)
continuous cast sheets (plates) for general-purpose use. The sheets may be colourless or coloured, and may
be transparent, translucent or opaque.
The thickness range of the sheets covered by this part of ISO 7823 is 1mm to 10mm.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 62:1999, Plastics — Determination of water absorption
1)
ISO 75-1:— , Plastics — Determination of temperature of deflection under load — Part 1: General test method
2)
ISO 75-2:— , Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 178:2001, Plastics — Determination of flexural properties
ISO 179-1:2000, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact
test
ISO 291:1997, Plastics — Standard atmospheres for conditioning and testing
3)
ISO 306:— , Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 489:1999, Plastics — Determination of refractive index
ISO 527-1:1993, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2:1993, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 877:1994, Plastics — Methods of exposure to direct weathering, to weathering using glass-filtered daylight,
and to intensified weathering by daylight using Fresnel mirrors
1) To be published. (Revision of ISO 75-1:1993)
2) To be published. (Revision of ISO 75-2:1993)
3) To be published. (Revision of ISO 306:1994)
©
ISO 2003 – All rights reserved 1
---------------------- Page: 10 ----------------------
ISO 7823-3:2003(E)
4)
ISO 1183-1:— , Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
5)
ISO 1183-2:— , Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density
gradient column method
ISO 2039-2:1987, Plastics — Determination of hardness — Part 2: Rockwell hardness
ISO 2818:1994, Plastics — Preparation of test specimens by machining
ISO 2859-1:1999, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by
acceptance quality limit (AQL) for lot-by-lot inspection
ISO 4582:1998, Plastics — Determination of changes in colour and variations in properties after exposure to
daylight under glass, natural weathering or laboratory light sources
ISO 4892-2:1994, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc sources
ISO 4892-4:1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.