SIST EN ISO 1179-2:2014

Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2013)

This part of ISO 1179 specifies dimensions, performance requirements and test procedures for heavyduty (S series) and light-duty (L series) stud ends with ISO 228-1 threads and the elastomeric sealing (type E) that is used with them. Heavy-duty (S series) stud ends with type E sealing in accordance with this part of ISO 1179 can be used at working pressures up to 63 MPa (630 bar). Light-duty (L series) stud ends with type E sealing in accordance with this part of ISO 1179 can be used at working pressures up to 25 MPa (250 bar). The permissible working pressure depends upon size, materials, design, working conditions, application, etc. Conformance to the dimensional information in this part of ISO 1179 does not guarantee rated performance. It is the responsibility of each manufacturer to perform testing according to the specification contained in this part of ISO 1179 in order to ensure that components made to this part of ISO 1179 comply with the performance ratings.

Leitungsanschlüsse für allgemeine Anwendung und Fluidtechnik - Einschraublöcher und Einschraubzapfen mit Gewinde nach ISO 228-1 und Elastomerdichtung oder metallener Dichtkante - Teil 2: Einschraubzapfen mit Elastomerdichtung (Form E), schwere (S) und leichte Reihe (L) (ISO 1179-2:2013)

Dieser Teil von ISO 1179 legt Maße, Leistungsanforderungen und Prüfverfahren für Einschraubzapfen der schweren Reihe (S-Reihe) und der leichten Reihe (L-Reihe) mit Gewinde nach ISO 228-1 und Elastomerdichtung (Form E) fest.
Einschraubzapfen der schweren Reihe (S-Reihe) mit Dichtung der Form E, die diesem Teil von ISO 1179 entsprechen, können bei Arbeitsdrücken bis 63 MPa (630 bar) eingesetzt werden. Einschraubzapfen der leichten Reihe (L-Reihe) mit Dichtung der Form E, die diesem Teil von ISO 1179 entsprechen, können bei Arbeitsdrücken bis 25 MPa (250 bar) eingesetzt werden. Der zulässige Arbeitsdruck ist von Größe, Werkstoffen, Konstruktion, Betriebsbedingungen, Anwendung, usw. abhängig.
Übereinstimmung mit den Maßangaben in diesem Teil von ISO 1179 garantiert keine Nennleistung. Es liegt in der Verantwortung jedes Herstellers, Prüfungen entsprechend den Festlegungen dieses Teils von ISO 1179 durchführen, um sicherzustellen, dass die nach diesem Teil von ISO 1179 hergestellten Bauteile mit den Nennleistungen übereinstimmen.
ANMERKUNG 1   Dieser Teil von ISO 1179 gilt für Verschraubungen nach ISO 8434 1 und ISO 8434 2.
ANMERKUNG 2   Die Einleitung dieses Teils von ISO 1179 enthält Empfehlungen für Einschraublöcher und  zapfen für Neukonstruktionen in hydraulischen und pneumatischen Kraftübertragungsanlagen.

Raccordements pour applications générales et transmissions hydrauliques et pneumatiques - Orifices et éléments mâles à filetage ISO 228-1 et joint en élastomère ou étanchéité métal sur métal - Partie 2: Éléments mâles de séries légère (série L) et lourde (série S) avec joint en élastomère (type E) (ISO 1179-2:2013)

L'ISO 1179-2:2013 spécifie les dimensions, les exigences de performance et les modes opératoires d'essai des éléments mâles à filetage ISO 228-1 de série lourde (série S) et de série légère (série L) avec joint élastomère (type E) qui est utilisé avec ceux-ci.
Les éléments mâles de série lourde (série S) avec étanchéité de type E conformes à l'ISO 1179-2:2013 peuvent être utilisés jusqu'à des pressions d'utilisation de 63 MPa (630 bar). Les éléments mâles de série légère (série L) avec étanchéité de type E conformes à l'ISO 1179-2:2013 peuvent être utilisés jusqu'à des pressions d'utilisation de 25 MPa (250 bar). La pression d'utilisation admissible dépend des dimensions, des matériaux, de la conception, des conditions d'exploitation, des applications, etc.

Priključki za splošno uporabo in za fluidno tehniko - Odprtine in priključki z navoji po ISO 228-1 z elastomernim ali kovinskim tesnjenjem - 2. del: Zelo obremenjeni ravni priključki (vrsta S) in malo obremenjeni ravni priključki (vrsta L) z elastomernim tesnjenjem (tip E) (ISO 1179-2:2013)

Ta del standarda ISO 1179 določa mere, zahtevane lastnosti in preskusne postopke za zelo obremenjene (vrsta S) in malo obremenjene (vrsta L) priključke z navoji po standardu ISO 228-1 ter za elastomerno tesnjenje (tip E), ki se z njimi uporablja. Zelo obremenjeni priključki (vrsta S) s tesnjenjem tipa E v skladu s tem delom standarda ISO 1179 se lahko uporabljajo pri delovnem tlaku do 63 MPa (630 barov). Malo obremenjeni priključki (vrsta S) s tesnjenjem tipa E v skladu s tem delom standarda ISO 1179 se lahko uporabljajo pri delovnem tlaku do 25 MPa (250 barov). Dovoljeni delovni tlak je odvisen od velikosti, materialov, zasnove, delovnih pogojev, primerov uporabe ipd. Skladnost z informacijami o merah v tem delu standarda ISO 1179 ne zagotavlja nazivne zmogljivosti. Vsak proizvajalec je odgovoren za preskušanje v skladu s specifikacijo, vsebovano v tem delu standarda ISO 1179, s čimer zagotovi, da so komponente, izdelane v skladu s tem delom standarda ISO 1179, skladne z ocenami zmogljivosti.

General Information

• Status: Withdrawn
• Publication Date: 25-May-2014
• Withdrawal Date: 04-Dec-2022
• ICS: 23.100.40 - Piping and couplings
• Technical Committee: IFEK - Ferrous metals
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 05-Dec-2022
• Due Date: 28-Dec-2022
• Completion Date: 05-Dec-2022
• Ref Project: EN ISO 1179-2:2013 - Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2013)

Relations

• Replaced By: SIST EN ISO 1179-2:2023 - Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2022)
• Effective Date: 30-Nov-2022
• Replaces: SIST EN ISO 1179-2:2008 - Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2007)
• Effective Date: 01-Jul-2014
• Replaces: SIST EN ISO 1179-2:2008 - Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2007)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 1179-2:2014
01-julij-2014
1DGRPHãþD
SIST EN ISO 1179-2:2008
3ULNOMXþNL]DVSORãQRXSRUDERLQ]DIOXLGQRWHKQLNR2GSUWLQHLQSULNOMXþNL]QDYRML
SR,62]HODVWRPHUQLPDOLNRYLQVNLPWHVQMHQMHPGHO=HORREUHPHQMHQL
UDYQLSULNOMXþNLYUVWD6LQPDORREUHPHQMHQLUDYQLSULNOMXþNLYUVWD/]
HODVWRPHUQLPWHVQMHQMHPWLS(,62
Connections for general use and fluid power - Ports and stud ends with ISO 228-1
threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and
light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2013)
Leitungsanschlüsse für allgemeine Anwendung und Fluidtechnik - Einschraublöcher und
Einschraubzapfen mit Gewinde nach ISO 228-1 und Elastomerdichtung oder metallener
Dichtkante - Teil 2: Einschraubzapfen mit Elastomerdichtung (Form E), schwere (S) und
leichte Reihe (L) (ISO 1179-2:2013)
Raccordements pour applications générales et transmissions hydrauliques et
pneumatiques - Orifices et éléments mâles à filetage ISO 228-1 et joint en élastomère ou
étanchéité métal sur métal - Partie 2: Éléments mâles de séries légère (série L) et lourde
(série S) avec joint en élastomère (type E) (ISO 1179-2:2013)
Ta slovenski standard je istoveten z: EN ISO 1179-2:2013
ICS:
23.100.40 Cevna napeljava in sklopke Piping and couplings
SIST EN ISO 1179-2:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1179-2:2014

---------------------- Page: 2 ----------------------

SIST EN ISO 1179-2:2014

EUROPEAN STANDARD
EN ISO 1179-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2013
ICS 23.100.40
English Version
Connections for general use and fluid power - Ports and stud
ends with ISO 228-1 threads with elastomeric or metal-to-metal
sealing - Part 2: Heavy-duty (S series) and light-duty (L series)
stud ends with elastomeric sealing (type E) (ISO 1179-2:2013)
Raccordements pour applications générales et Leitungsanschlüsse für allgemeine Anwendung und
transmissions hydrauliques et pneumatiques - Orifices et Fluidtechnik - Einschraublöcher und Einschraubzapfen mit
éléments mâles à filetage ISO 228-1 et joint en élastomère Gewinde nach ISO 228-1 und Elastomerdichtung oder
ou étanchéité métal sur métal - Partie 2: Éléments mâles de metallener Dichtkante - Teil 2: Einschraubzapfen mit
séries légère (série L) et lourde (série S) avec joint en Elastomerdichtung (Form E), schwere (S) und leichte Reihe
élastomère (type E) (ISO 1179-2:2013) (L) (ISO 1179-2:2013)
This European Standard was approved by CEN on 12 October 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1179-2:2013 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 1179-2:2014
EN ISO 1179-2:2013 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 1179-2:2014
EN ISO 1179-2:2013 (E)
Foreword
This document (EN ISO 1179-2:2013) has been prepared by Technical Committee ISO/TC 131 "Fluid power
systems" in collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings”
the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2014, and conflicting national standards shall be withdrawn at the
latest by May 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1179-2:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 1179-2:2013 has been approved by CEN as EN ISO 1179-2:2013 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 1179-2:2014

---------------------- Page: 6 ----------------------

SIST EN ISO 1179-2:2014
INTERNATIONAL ISO
STANDARD 1179-2
Second edition
2013-11-01
Connections for general use and fluid
power — Ports and stud ends with
ISO 228-1 threads with elastomeric or
metal-to-metal sealing —
Part 2:
Heavy-duty (S series) and light-duty
(L series) stud ends with elastomeric
sealing (type E)
Raccordements pour applications générales et transmissions
hydrauliques et pneumatiques — Orifices et éléments mâles à filetage
ISO 228-1 et joint en élastomère ou étanchéité métal sur métal —
Partie 2: Éléments mâles de séries légère (série L) et lourde (série S)
avec joint en élastomère (type E)
Reference number
ISO 1179-2:2013(E)
©
ISO 2013

---------------------- Page: 7 ----------------------

SIST EN ISO 1179-2:2014
ISO 1179-2:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 1179-2:2014
ISO 1179-2:2013(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Dimensions . 2
5 Requirements . 2
5.1 Working pressure . 2
5.2 Performance . 2
6 Elastomeric seals . 2
7 Test methods . 2
7.1 Burst pressure test (failure pressure test) . 2
7.2 Cyclic endurance (impulse) test . 3
7.3 Test report . 3
7.4 Re-use of components . 3
8 Designation of stud ends . 3
9 Identification statement (reference to this part of ISO 1179) . 4
Annex A (normative) Test data form for ISO 1179-1 port and ISO 1179-2 stud ends .9
Bibliography .10
© ISO 2013 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 1179-2:2014
ISO 1179-2:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 4,
Connectors and similar products and components.
This second edition cancels and replaces the first edition (ISO 1179-2:2007), which has been
technically revised.
ISO 1179 consists of the following parts, under the general title Connections for general use and fluid
power — Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing:
— Part 1: Threaded ports
— Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E)
— Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H)
— Part 4: Stud ends for general use only with metal-to-metal sealing (type B)
iv © ISO 2013 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 1179-2:2014
ISO 1179-2:2013(E)

Introduction
In fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under
pressure within a circuit. In general applications, a fluid can be conveyed under pressure. Components
are connected through their threaded ports by fluid conductor connectors to tubes and pipes or to hose
fittings and hoses.
For threaded ports and stud ends specified in new designs in hydraulic fluid power applications,
ISO/TC 131/SC 4 recommends that the ISO 6149 series be used because these International Standards specify
ports and stud ends with metric threads and O-ring sealing and because the subcommittee would like to
help users by recommending one preferred system. ISO/TC 131/SC 4 further recommends that threaded
ports and stud ends in accordance with the ISO 1179 series, ISO 9974 series and ISO 11926 series not be
used for new designs in hydraulic fluid power applications; these International Standards are maintained
because they specify ports and stud ends that are currently used in hydraulic systems worldwide.
For threaded ports and stud ends specified in new designs in pneumatic fluid power applications,
ISO/TC 131/SC 4 recommends that ISO 16030 be used, except where products are to interface with
ISO 7-1 threads, because the subcommittee would like to help users by recommending one preferred
system. ISO/TC 131/SC 4 further recommends that threaded ports and stud ends in accordance with the
ISO 1179 series not be used for new designs in pneumatic fluid power applications; these International
Standards are maintained because they specify ports and stud ends that are currently used in pneumatic
systems worldwide.
Significant testing over more than 35 years of use has confirmed the performance requirements of
connection ends made from carbon steel. The stud end connections specified in ISO 1179-2, ISO 1179-3
and ISO 1179-4 apply to connectors detailed in ISO 8434-1, ISO 8434-2 and ISO 8434-4.
© ISO 2013 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 1179-2:2014

---------------------- Page: 12 --
...