kSIST FprEN ISO 5978:2023

Rubber- or plastics-coated fabrics - Determination of blocking resistance (ISO/FDIS 5978:2023)

This document specifies a method for the determination of the resistance of rubber- or plastics-coated fabric sheets to blocking when left in contact for specified temperature, time and pressure.

Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung des Blockwiderstandes (ISO/FDIS 5978:2023)

Dieses Dokument legt ein Verfahren zur Bestimmung der Widerstandsfähigkeit von gummi- oder kunststoffbeschichtetem Gewebefolien gegen Blocken fest, wenn diese bei festgelegter Temperatur, festgelegter Zeit und festgelegtem Druck in Kontakt gebracht werden.

Supports textiles revêtus de caoutchouc ou de plastique - Détermination de la résistance au blocage (ISO/FDIS 5978:2023)

Le présent document spécifie une méthode de détermination de la résistance au blocage des supports textiles en feuilles revêtus de caoutchouc ou de plastique lorsqu’ils sont laissés en contact dans des conditions spécifiées de température, de temps et de pression.

Gumirane ali plastificirane tekstilije - Ugotavljanje odpornosti proti zlepljenju in luščenju (ISO/DIS 5978:2022)

General Information

• Status: Not Published
• Public Enquiry End Date: 14-Sep-2022
• ICS: 59.080.40 - Coated fabrics
• Technical Committee: ITEK - Textile and textile products
• Current Stage: 5020 - Formal vote (FV) (Adopted Project)
• Start Date: 18-May-2023
• Due Date: 06-Jul-2023
• Completion Date: 22-May-2023
• Ref Project: EN ISO 5978:2023 - Rubber- or plastics-coated fabrics - Determination of blocking resistance (ISO 5978:2023)

Relations

• Revised: SIST EN 25978:1999 - Rubber- or plastics-coated fabrics - Determination of blocking resistance (ISO 5978:1990)
• Effective Date: 24-Feb-2021
• Revised: SIST EN 25978:1999 - Rubber- or plastics-coated fabrics - Determination of blocking resistance (ISO 5978:1990)
• Effective Date: 18-Jan-2023
• Revised: SIST EN 25978:1999 - Rubber- or plastics-coated fabrics - Determination of blocking resistance (ISO 5978:1990)
• Effective Date: 19-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 5978:2022
01-september-2022
Gumirane ali plastificirane tekstilije - Ugotavljanje odpornosti proti zlepljenju in
luščenju (ISO/DIS 5978:2022)
Rubber or plastics-coated fabrics - Determination of blocking resistance (ISO/DIS
5978:2022)
Mit Kautschuk oder Kunststoff beschichtete Textilien – Bestimmung des
Blockwiderstandes (ISO/DIS 5978:2022)
Supports textiles revêtus de caoutchouc ou de plastique - Détermination de la résistance
au blocage (ISO/DIS 5978:2022)
Ta slovenski standard je istoveten z: prEN ISO 5978
ICS:
59.080.40 Površinsko prevlečene Coated fabrics
tekstilije
oSIST prEN ISO 5978:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 5978:2022

---------------------- Page: 2 ----------------------
oSIST prEN ISO 5978:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 5978
ISO/TC 45/SC 4 Secretariat: DSM
Voting begins on: Voting terminates on:
2022-06-14 2022-09-06
Rubber or plastics-coated fabrics — Determination of
blocking resistance
ICS: 59.080.40
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 5978:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022

---------------------- Page: 3 ----------------------
oSIST prEN ISO 5978:2022
ISO/DIS 5978:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2022 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 5978:2022
ISO/DIS 5978:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test equipment .1
4.1 Lower glass plate . 1
4.2 Upper glass plate. 1
4.3 Strips of filter paper . 2
4.4 Weight-piece. 2
4.5 Circulating-air oven . 2
5 Time between manufacture and testing . 2
6 Samples and test pieces . 2
7 Conditioning of test pieces .3
8 Procedure .3
9 Test report . 3
iii
© ISO 2022 – All rights reserved

---------------------- Page: 5 ----------------------
oSIST prEN ISO 5978:2022
ISO/DIS 5978:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electro
technical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 4, Products (other than hoses).
This second edition cancels and replaces the first edition (ISO 5978:1990), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— adoptio
...