iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 812:1998

(Main)

Industrial bump caps

Industrial bump caps

This European Standard specifies physical and performance requirements, methods of test and marking requirements for industrial bump caps. Industrial bump caps are intended to provide protection to the wearer against the effects of striking  his head against hard, stationary objects with sufficient severity to cause laceration or other superficial injuries. They are not intended to provide protection against the effects of falling or thrown objects, or moving or suspended loads.  NOTE : An industrial bump cap should not  be confused with an industrial  safety  helmet as specified in EN 397.

Industrie-Anstoßkappe

Diese Europäische Norm legt physikalische Anforderungen und Leistungsanforderungen, Prüfverfahren und die Kennzeichnung von Industrie- Anstoßkappen fest. Industrie-Anstoßkappen dienen dem Kopfschutz des Trägers, wenn der Kopf so stark gegen harte, feststehende Gegenstände prallt, daß es zu einer Platzwunde oder anderen oberflächlichen Verletzungen bis hin zur Selbst-betäubung kommt. Anstoßkappen bieten keinen Schutz gegen die Wirkung fallender oder geworfener Gegenstände, oder sich bewegender oder herabhängender Lasten.

Casquettes anti-heurt pour l'industrie

La présente norme européenne spécifie les exigences physiques et de performance, les méthodes d'essai et les exigences de marquage des casquettes anti-heurt pour l'industrie. Les casquettes anti-heurt pour l'industrie sont destinées a protéger le porteur lorsque sa tete vient heurter des objets durs et immobiles avec suffisamment de force pour provoquer des lacérations ou autres blessures superficielles. Elles ne sont pas destinées a protéger des effets des projections ou chutes d'objets ou des charges en suspension ou en mouvement.

Lahke industrijske čelade za varovanje pred udarci

General Information

Status
Withdrawn
Publication Date
31-Mar-1998
Withdrawal Date
03-Jun-2012
ICS
13.340.20 - Head protective equipment
Technical Committee
OVP - Personal protecting equipment
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
04-Jun-2012
Due Date
27-Jun-2012
Completion Date
04-Jun-2012
Directive
89/686/EEC - Council Directive 89/686/EEC of 21 December 1989 on the approximation of the laws of the Member States relating to personal protective equipment
Mandate
M/BC/CEN/90/2 - Order for standardization concerning Personal Protective Equipment (P.P.E.)
Ref Project
EN 812:1997 - Industrial bump caps

Relations

Amended By
SIST EN 812:1998/A1:2002 - Industrial bump caps
Effective Date
22-Dec-2008
Replaced By
SIST EN 812:2012 - Industrial bump caps
Effective Date
01-Jul-2012
Amended By
SIST EN 812:1998/A1:2002 - Industrial bump caps
Effective Date
08-Jun-2022

Buy Standard

EN 812:1998EN 812:1998
PreviousNext
Standard
EN 812:1998
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 812:1998
01-april-1998
/DKNHLQGXVWULMVNHþHODGH]DYDURYDQMHSUHGXGDUFL
Industrial bump caps
Industrie-Anstoßkappe
Casquettes anti-heurt pour l'industrie
Ta slovenski standard je istoveten z: EN 812:1997
ICS:
13.340.20 Varovalna oprema za glavo Head protective equipment
SIST EN 812:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 812:1998

---------------------- Page: 2 ----------------------

SIST EN 812:1998

---------------------- Page: 3 ----------------------

SIST EN 812:1998

---------------------- Page: 4 ----------------------

SIST EN 812:1998

---------------------- Page: 5 ----------------------

SIST EN 812:1998

---------------------- Page: 6 ----------------------

SIST EN 812:1998

---------------------- Page: 7 ----------------------

SIST EN 812:1998

---------------------- Page: 8 ----------------------

SIST EN 812:1998

---------------------- Page: 9 -------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1384:2023(Main)
Helmets for equestrian activities
EN 1384:2023

This European Standard specifies requirement for protective helmets that may or may not have a peak, for people involved in equestrian activities. It gives safety requirements that include methods of test and levels of performance for shock absorption, for resistance to penetration and for the strength and effectiveness of the retention system and the deflection of a peak if fitted.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 17946:2023(Main)
Helmets for S-EPAC riders
CEN/TS 17946:2023

This document specifies requirements and test methods for helmets worn by users of speed electrically power assisted bicycles (S-EPACs). This document also specifies requirements and test methods for integrated visors in helmets worn by users of S-EPACS.
Requirements and the corresponding methods of test are given for the following:
-   construction, including field of vision;
-   shock absorbing properties;
-   retention system properties, including chin strap and fastening devices;
-   marking and information.

  • Technical specification
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16321-1:2022(Main)
Eye and face protection for occupational use - Part 1: General requirements (ISO 16321-1:2021)
EN ISO 16321-1:2022

This document specifies general requirements for protectors designed to provide protection for the eyes and
faces of persons against common occupational hazards such as impacts from flying particles and fragments,
optical radiation, dusts, splashing materials, molten metals, heat, flame, hot solids, harmful gases, vapours
and aerosols.
Additional requirements for protectors used during welding and related techniques and for mesh protectors
are given in ISO 16321-2 and ISO 16321-3.
This document applies to all afocal (plano power) and prescription lens protectors and components.
This document also applies to those articles of eye and face protection used for occupational-type tasks but
not performed as part of an occupation, e.g. "do-it-yourself".
This document does not apply to:
— sunglasses for general use for which ISO 12312-1 applies;
— protectors for medically prescribed applications (not occupational); e.g. eye protection for severe
dry eye, tints prescribed for medical conditions;
— protectors intended to control exposure of the eyes of patients during diagnosis or treatment (e.g.
ISO/DTR 22463);
— protectors for use during medical or aesthetic applications intense light sources (ILS) for which ISO
12609 series applies;
— protectors intended for direct observation of the sun, such as for solar-eclipse viewing for which
ISO 12312-2 applies;
— protectors specifically intended for sports for which ISO 18527 series applies;
— laser protectors, for which ISO 19818 applies;
— face protectors intended for live-working to protect against short-circuit electric arcs for which
IEC 62819 applies;
— protectors intended to protect against ionizing radiation for which IEC 61331-3 applies.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 12312-1:2022(Main)
Eye and face protection - Sunglasses and related eyewear - Part 1: Sunglasses for general use (ISO 12312-1:2022)
EN ISO 12312-1:2022

This document is applicable to all afocal (plano power) sunglasses and clip-ons for general use, including
road use and driving, intended for protection against solar radiation.
Information on the use of sunglass filters is given in Annex A. Requirements for unmounted filters used
as replacement or alternative filters are given in Annex C.
This document is not applicable to:
a) eyewear for protection against radiation from artificial light sources;
b) eye protectors intended for specific sports (e.g. ski goggles or other types – see ISO18527 (all parts));
c) sunglasses that have been medically prescribed for attenuating solar radiation;
d) products intended for direct observation of the sun, such as for viewing a partial or annular solar
eclipse, for which ISO 12312-2 applies;
e) products intended for occupational eye protection – see, for example, ISO 16321 (all parts)

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 18527-1:2022(Main)
Eye and face protection for sports use - Part 1: Requirements for downhill skiing and snowboarding goggles (ISO 18527-1:2021)
EN ISO 18527-1:2022

This International Standard applies to all afocal (plano power) goggles, intended for eye protection against
hazards including ultraviolet and visible solar radiation, rain, snow and wind, during downhill skiing, snowboarding
and other activities with similar hazards and no greater risks.
It deals with materials, construction, optical properties, testing, labelling and marking.
Requirements for the marking of goggles and for information to be supplied by the manufacturer are also
specified.
Information on the selection and use of ski and snow-boarding goggles is given in Annex A.
This International Standard does not apply to:
a) eyewear for protection when operating or travelling on a motorized vehicle;
b) eyewear for protection against radiation from artificial light sources, such as those used in
solaria;
c) eyewear for direct observation of the sun;
d) eye protectors intended for sports with unrelated hazards and risks.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16321-3:2022(Main)
Eye and face protection for occupational use - Part 3: Additional requirements for mesh protectors (ISO 16321-3:2021)
EN ISO 16321-3:2022

This document specifies additional requirements for mesh protectors designed to provide protection
for the eyes and faces of persons against mechanical hazards such as impacts from flying particles and
fragments.
The other applicable requirements for mesh protectors and the frames/mountings to which they are
intended to be fitted are given in ISO 16321-1.
This document specifies materials, design, performance requirements, and marking requirements for
mesh protectors that are different from and/or supplement ISO 16321-1.
This document is not applicable to protectors for use against liquid splash (including molten metal), hot
solid risks, electrical hazards, infrared and ultraviolet radiation. For protection against these hazards
suitable additional or alternative protectors according ISO 16321-1 will be needed.
Mesh protectors for use in sports such as fencing are excluded.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17479:2022(Main)
Hearing protectors - Guidance on selection of individual fit testing methods
EN 17479:2021

This document gives guidance on the appropriate selection of fit testing methods and measurement, and provides practical guidance on fit testing methods, their uses and limitations.
This document does not specify the technical requirements for manufacturing fit testing equipment.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16321-2:2021(Main)
Eye and face protection for occupational use - Part 2: Additional requirements for protectors used during welding and related techniques (ISO 16321-2:2021)
EN ISO 16321-2:2021

This document specifies additional requirements for eye and face protectors designed to provide protection
for the eyes and faces of persons against occupational hazards during welding and allied processes, such as
optical radiation, impacts from flying particles and fragments, and hot solids.
This document also applies to those articles of eye- and face-protection used for occupational-type tasks but
not performed as part of an occupation, e.g. "do-it-yourself".
This document specifies materials, design, performance requirements, and marking requirements for
welding protectors which are different from and/or supplement ISO 16321-1.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 18527-2:2021(Main)
Eye and face protection for sports use - Part 2: Requirements for eye protectors for squash and eye protectors for racquetball and squash 57 (ISO 18527-2:2021)
EN ISO 18527-2:2021

This International Standard applies to all eye protectors intended for eye protection against hazards during the
sports of Squash, Racquetball and Squash 57 and sports with similar hazards and no greater risks.
It deals with materials, construction, optical properties, testing, labelling and marking.
It applies to eye protectors that incorporate prescription lenses, but not to eye protectors designed for use
over spectacles.
Requirements for the marking of eye protectors and for information to be supplied by the manufacturer are
also specified.
Information on the selection and use of eye protectors for Squash, Racquetball and Squash 57 is given in
Annex A.
This International Standard does not apply to:
a. sports eye protectors designed for use over prescription spectacles;
b. eye protectors for occupational applications;
c. eye protectors without lenses;
d. eye protectors for sports where the hazards are unrelated to the hazards in or involve greater risks
than Squash, Racquetball and Squash 57.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19818-1:2021(Main)
Eye and face protection - Protection against laser radiation - Part 1: Requirements and test methods (ISO 19818-1:2021)
EN ISO 19818-1:2021

This document applies to eye and face protectors intended to provide protection against accidental
exposure to laser radiation within the wavelength range 180 nm to 1 mm. It defines the requirements,
test methods and marking. Laser protective filters used for intentional exposure to laser radiation, as
viewing windows in laser equipment or incorporated into optical instruments such as operating
microscopes which may be used for deliberate viewing of laser radiation as part of their function, and
loupes, are outside the scope of this document.
This document is applicable to devices intended for patient protection during medical laser procedures
except for treatment in the periorbital area.
The eye protection described in this document is intended for use at normal ambient temperature (23 ±
5)°C, unless specified in particular requirement(s).

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    German language
    sale 10% off
    e-Library read for
    1 day