SIST EN 303 883-2 V1.2.1:2021
(Main)Short Range Devices (SRD) and Ultra Wide Band (UWB) - Part 2: Measurement techniques for receiver requirements
Short Range Devices (SRD) and Ultra Wide Band (UWB) - Part 2: Measurement techniques for receiver requirements
The present document provides measurement procedures for receiver requirements to address the spectrum efficiency
requirements of the RED [i.10].
The baseline receiver concept is a set of two parameters given in clause 5 of the present document providing guidance
for HS development, which can be further refined by the responsible TB.
Baseline receiver concept comprises the following parameters:
• Receiver Baseline Sensitivity (RBS); and
• Receiver Baseline Resilience (RBR).
The Baseline receiver concept is a further development of the signal interferer handling concept, see ETSI
TS 103 361 [i.4].
Naprave kratkega dosega (SRD) in ultra širokopasovna (UWB) tehnologija - 2. del: Merilne tehnike za zahteve sprejemnika
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 303 883-2 V1.2.1 (2021-02)
EUROPEAN STANDARD
Short Range Devices (SRD) and
Ultra Wide Band (UWB);
Part 2: Measurement techniques
for receiver requirements
---------------------- Page: 1 ----------------------
2 ETSI EN 303 883-2 V1.2.1 (2021-02)
Reference
REN/ERM-TGUWB-149-2
Keywords
measurement, receiver, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 883-2 V1.2.1 (2021-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 11
4 General . 12
5 Receiver Requirements. 12
5.1 General Guidance on RX measurement . 12
5.2 Receiver Spurious Emissions . 12
5.2.1 Description . 12
5.2.2 Limits . 12
5.2.3 Conformance. 13
5.2.3.1 General . 13
5.2.3.2 Step 1: Measurement with Peak Detector . 13
5.2.3.3 Step 2: Measurement with RMS Detector . 14
5.3 Use-Case Specific Input Parameters for Receiver Baseline Requirements . 14
5.3.1 Introduction. 14
5.3.2 Technical Wanted Performance Criteria . 15
5.3.3 Examples of Use-Case Specific Input Parameter for Receiver Tests . 15
5.3.3.1 Communication/Location Tracking Device . 15
5.3.3.2 Radio Determination Device (non-contact based) . 16
5.3.3.3 Material contact-based radio determination device . 18
5.4 Receiver Baseline Sensitivity (RBS) . 20
5.4.1 Description . 20
5.4.2 Limits . 20
5.4.3 Conformance. 21
5.4.3.1 General . 21
5.4.3.2 Conducted measurements for radio communication devices . 21
5.4.3.2.0 General . 21
5.4.3.2.1 Step 1: Technical Wanted Performance Criteria . 21
5.4.3.2.2 Step 2: Sensitivity Requirement (Power) . 21
5.4.3.2.3 Step 3: Measurement Procedure . 21
5.4.3.2.4 Step 4: Technical Wanted Performance Criteria Assessment . 23
5.4.3.3 Radiated Measurements for Radio Communication Devices with Power Limit . 23
5.4.3.3.0 General . 23
5.4.3.3.1 Step 1: Technical Wanted Performance Criteria . 23
5.4.3.3.2 Step 2: Sensitivity Requirement (Power) . 23
5.4.3.3.3 Step 3: Measurement Procedure . 23
5.4.3.3.4 Step 4: Technical Wanted Performance Criteria Assessment . 25
5.4.3.4 Radiated measurements for radio communication devices with distance limit . 25
5.4.3.4.0 General . 25
5.4.3.4.1 Step 1: Technical Wanted Performance Criteria . 25
5.4.3.4.2 Step 2: Sensitivity Requirement (Distance) . 25
5.4.3.4.3 Step 3: Measurement Procedure . 26
5.4.3.4.4 Step 4: Technical Wanted Performance Criteria Assessment . 26
5.4.3.5 Radiated Measurements for Radiodetermination Applications with Distance Limit . 26
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 883-2 V1.2.1 (2021-02)
5.4.3.5.0 General . 26
5.4.3.5.1 Step 1: Technical Performance Criteria . 26
5.4.3.5.2 Step 2: Sensitivity Requirement (Distance) . 27
5.4.3.5.3 Step 3: Measurement Procedure . 27
5.4.3.5.4 Step 4: Technical Wanted Performance Criteria Assessment . 28
5.4.3.6 Conducted measurements for radio determination devices . 28
5.4.3.6.0 General . 28
5.4.3.6.1 Step 1: Technical Wanted Performance Criteria . 28
5.4.3.6.2 Step 2: Sensitivity Requirement (Power) . 28
5.4.3.6.3 Step 3: Measurement Procedure . 29
5.4.3.6.4 Step 4: Technical Wanted Performance Criteria Assessment . 30
5.5 Receiver Baseline Resilience (RBR) . 30
5.5.1 Description . 30
5.5.2 RBR Requirements . 30
5.5.2.1 Interferer test signal. 30
5.5.2.2 RBR wanted performance criteria . 30
5.5.3 Conformance. 31
5.5.3.1 General . 31
5.5.3.2 Conducted Measurements for Radio Communication Devices . 31
5.5.3.2.1 Step 1: Start with the RBS Setup . 31
5.5.3.2.2 Step 2: Adding Interfering Signal Source . 31
5.5.3.2.3 Step 3: Degradation of Sensitivity Requirement . 31
5.5.3.2.4 Step 4: Test of Technical Wanted Performance Criteria . 31
5.5.3.2.5 Step 5: Measurement Assessment . 32
5.5.3.2.6 Step 6: Repetition of steps 4 and 5 . 32
5.5.3.3 Radiated Measurements for Radio Communication Devices with Power Limit . 32
5.5.3.3.1 Step 1: Start with the RBS Setup . 32
5.5.3.3.2 Step 2: Adding Interfering Signal Source . 32
5.5.3.3.3 Step 3: Degradation of Sensitivity Requirement . 32
5.5.3.3.4 Step 4: Test of Technical Wanted Performance Criteria . 33
5.5.3.3.5 Step 5: Measurement Assessment . 33
5.5.3.3.6 Step 6: Repetition of steps 4 and 5 . 33
5.5.3.4 Radiated Measurements for Radio Communication Devices with Distance Limit . 33
5.5.3.4.1 Step 1: Start with the RBS setup. 33
5.5.3.4.2 Step 2: Adding interfering signal source . 33
5.5.3.4.3 Step 3: Degradation of Sensitivity Requirement . 34
5.5.3.4.4 Step 4: Test of Technical Wanted Performance Criteria . 34
5.5.3.4.5 Step 5: Measurement Assessment . 34
5.5.3.4.6 Step 6: Repetition of steps 4 and 5 . 34
5.5.3.5 Radiated Measurements for Radiodetermination Applications with Distance Limit . 34
5.5.3.5.1 Step 1: Start with the RBS Setup . 34
5.5.3.5.2 Step 2: Adding interfering signal source . 34
5.5.3.5.3 Step 3: Degradation of Sensitivity Requirement . 35
5.5.3.5.4 Step 4: Test of Technical Wanted Performance Criteria . 36
5.5.3.5.5 Step 5: Measurement Assessment . 36
5.5.3.5.6 Step 6: Repetition of steps 4 and 5 . 36
5.5.3.6 Conducted Measurements for Radio Determination Devices . 36
5.5.3.6.1 Step 1: Start with the RBS Setup . 36
5.5.3.6.2 Step 2: Adding Interfering Signal Source . 36
5.5.3.6.3 Step 3: Degradation of Sensitivity Requirement . 36
5.5.3.6.4 Step 4: Test of Technical Performance Criteria . 37
5.5.3.6.5 Step 5: Measurement Assessment . 37
5.5.3.6.6 Step 6: Repetition of steps 4 and 5 . 37
Annex A (normative): Choose interferer for RBR . 38
A.1 Introduction . 38
A.2 Limits for the Interfering Signals . 39
A.2.1 Interferer within OFR . 39
A.2.1.0 Introduction. 39
A.2.1.1 Option 1 . 39
A.2.1.2 Option 2 . 39
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 883-2 V1.2.1 (2021-02)
A.2.2 Interferer outside OFR . 40
A.3 Guidance to Setup the Power Level of the Interfering Signals @ EUT for RBR tests . 40
A.3.1 Radiated tests . 40
A.3.2 Conducted tests . 42
Annex B (informative): Guidance on Scaling Receiver Sensitivity . 43
B.1 General . 43
B.2 Scaling of power at the EUT . 43
B.3 Scaling distance . 44
Annex C (informative): Justification of receiver requirements from ETSI EG 203 336 . 45
C.1 General . 45
C.2 Justification . 45
C.3 Summary for the RBR requirement . 47
C.4 Justification RBS-requirement for radio determination devices . 48
Annex D (informative): Object and Radar Cross Section . 50
D.1 Wanted objects . 50
D.2 Direct Object Reflectors . 52
D.3 Delay Line Object Reflectors . 54
D.4 Electronic Object Reflectors . 54
D.5 Test Setup with Conventional RCS within Chamber . 55
D.6 Test Setup with Radar Object Generator . 56
D.6.1 General . 56
Annex E (informative): Change History . 58
History . 59
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 303 883-2 V1.2.1 (2021-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and
Radio spectrum Matters (ERM).
The present document is part 2 of a multi-part deliverable covering Short Range Devices (SRD) and Ultra Wide Band
(UWB), as identified below:
Part 1: "Measurement techniques for transmitter requirements";
Part 2: "Measurement techniques for receiver requirements".
National transposition dates
Date of adoption of this EN: 22 February 2021
Date of latest announcement of this EN (doa): 31 May 2021
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2021
Date of withdrawal of any conflicting National Standard (dow): 30 November 2021
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 303 883-2 V1.2.1 (2021-02)
Introduction
The present document provides measurement procedures for receiver requirements to address the spectrum efficiency
requirements of the RED [i.10].
The basis for this RX concept was developed by ETSI during two Special Task Forces.
First Special Task Force: ETSI STF 494; Update of the UWB related Harmonised Standards covering the essential
requirements of article 3.2 of the RED [i.10].
The STF 494:
• Started: 2015-05-25
• Ended: 2016-03-31
Outcome:
• ETSI TS 103 361 [i.4]
The second Special Task Force: ETSI STF 541; Signal interferer handling, a new RX requirement to cover the
essential requirements of article 3.2 of the RED [i.10], was a continuation to implement and consider comments
received after the publication of the ETSI TS 103 361 [i.4].
The STF 541:
• Started: 2017-10-06
• Ended: 2019-05-31
Outcome:
• ETSI TR 103 566 [i.2]
• ETSI TS 103 567 [i.3]
There is no specification of receiver parameter values within the present document. These values will be derived from
technical specification defined by the responsible ETSI Technical Committees and/or the findings of regulatory studies
conducted by the relevant bodies like CEPT ECC WG SE. The limits/values for the baseline RX-conformance
requirements will be specified in the related standard.
In addition to the two receiver baseline requirements it can be necessary that the RX spurious emission requirement
could be a further RX requirement in the related standard. This could be necessary if the EUT has a receive only mode
or if it is not collocated to the transmitter. The present document specifies the receiver spurious emission requirement
and the corresponding test and measurement procedure in clause 5.2.
The present document provides practical information and guidance for the compliance receiver tests of UWB and Short
Range technology and devices.
It is recommended that, in drafting the related standards, a thorough analysis is conducted on all possible applicable
receiver parameters (see annex C), selecting the most appropriate RX-requirements and having a robust reasoning for
those that are disregarded.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 303 883-2 V1.2.1 (2021-02)
1 Scope
The present document provides measurement procedures for receiver requirements to address the spectrum efficiency
requirements of the RED [i.10].
The baseline receiver concept is a set of two parameters given in clause 5 of the present document providing guidance
for HS development, which can be further refined by the responsible TB.
Baseline receiver concept comprises the following parameters:
• Receiver Baseline Sensitivity (RBS); and
• Receiver Baseline Resilience (RBR).
The Baseline receiver concept is a further development of the signal interferer handling concept, see ETSI
TS 103 361 [i.4].
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EG 203 336 (V1.2.1): "Guide for the selection of technical paramet
...
SLOVENSKI STANDARD
SIST EN 303 883-2 V1.2.1:2021
01-april-2021
Naprave kratkega dosega (SRD) in ultra širokopasovna (UWB) tehnologija - 2. del:
Merilne tehnike za zahteve sprejemnika
Short Range Devices (SRD) and Ultra Wide Band (UWB) - Part 2: Measurement
techniques for receiver requirements
Ta slovenski standard je istoveten z: ETSI EN 303 883-2 V1.2.1 (2021-02)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
SIST EN 303 883-2 V1.2.1:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 303 883-2 V1.2.1:2021
---------------------- Page: 2 ----------------------
SIST EN 303 883-2 V1.2.1:2021
ETSI EN 303 883-2 V1.2.1 (2021-02)
EUROPEAN STANDARD
Short Range Devices (SRD) and
Ultra Wide Band (UWB);
Part 2: Measurement techniques
for receiver requirements
---------------------- Page: 3 ----------------------
SIST EN 303 883-2 V1.2.1:2021
2 ETSI EN 303 883-2 V1.2.1 (2021-02)
Reference
REN/ERM-TGUWB-149-2
Keywords
measurement, receiver, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 303 883-2 V1.2.1:2021
3 ETSI EN 303 883-2 V1.2.1 (2021-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 11
4 General . 12
5 Receiver Requirements. 12
5.1 General Guidance on RX measurement . 12
5.2 Receiver Spurious Emissions . 12
5.2.1 Description . 12
5.2.2 Limits . 12
5.2.3 Conformance. 13
5.2.3.1 General . 13
5.2.3.2 Step 1: Measurement with Peak Detector . 13
5.2.3.3 Step 2: Measurement with RMS Detector . 14
5.3 Use-Case Specific Input Parameters for Receiver Baseline Requirements . 14
5.3.1 Introduction. 14
5.3.2 Technical Wanted Performance Criteria . 15
5.3.3 Examples of Use-Case Specific Input Parameter for Receiver Tests . 15
5.3.3.1 Communication/Location Tracking Device . 15
5.3.3.2 Radio Determination Device (non-contact based) . 16
5.3.3.3 Material contact-based radio determination device . 18
5.4 Receiver Baseline Sensitivity (RBS) . 20
5.4.1 Description . 20
5.4.2 Limits . 20
5.4.3 Conformance. 21
5.4.3.1 General . 21
5.4.3.2 Conducted measurements for radio communication devices . 21
5.4.3.2.0 General . 21
5.4.3.2.1 Step 1: Technical Wanted Performance Criteria . 21
5.4.3.2.2 Step 2: Sensitivity Requirement (Power) . 21
5.4.3.2.3 Step 3: Measurement Procedure . 21
5.4.3.2.4 Step 4: Technical Wanted Performance Criteria Assessment . 23
5.4.3.3 Radiated Measurements for Radio Communication Devices with Power Limit . 23
5.4.3.3.0 General . 23
5.4.3.3.1 Step 1: Technical Wanted Performance Criteria . 23
5.4.3.3.2 Step 2: Sensitivity Requirement (Power) . 23
5.4.3.3.3 Step 3: Measurement Procedure . 23
5.4.3.3.4 Step 4: Technical Wanted Performance Criteria Assessment . 25
5.4.3.4 Radiated measurements for radio communication devices with distance limit . 25
5.4.3.4.0 General . 25
5.4.3.4.1 Step 1: Technical Wanted Performance Criteria . 25
5.4.3.4.2 Step 2: Sensitivity Requirement (Distance) . 25
5.4.3.4.3 Step 3: Measurement Procedure . 26
5.4.3.4.4 Step 4: Technical Wanted Performance Criteria Assessment . 26
5.4.3.5 Radiated Measurements for Radiodetermination Applications with Distance Limit . 26
ETSI
---------------------- Page: 5 ----------------------
SIST EN 303 883-2 V1.2.1:2021
4 ETSI EN 303 883-2 V1.2.1 (2021-02)
5.4.3.5.0 General . 26
5.4.3.5.1 Step 1: Technical Performance Criteria . 26
5.4.3.5.2 Step 2: Sensitivity Requirement (Distance) . 27
5.4.3.5.3 Step 3: Measurement Procedure . 27
5.4.3.5.4 Step 4: Technical Wanted Performance Criteria Assessment . 28
5.4.3.6 Conducted measurements for radio determination devices . 28
5.4.3.6.0 General . 28
5.4.3.6.1 Step 1: Technical Wanted Performance Criteria . 28
5.4.3.6.2 Step 2: Sensitivity Requirement (Power) . 28
5.4.3.6.3 Step 3: Measurement Procedure . 29
5.4.3.6.4 Step 4: Technical Wanted Performance Criteria Assessment . 30
5.5 Receiver Baseline Resilience (RBR) . 30
5.5.1 Description . 30
5.5.2 RBR Requirements . 30
5.5.2.1 Interferer test signal. 30
5.5.2.2 RBR wanted performance criteria . 30
5.5.3 Conformance. 31
5.5.3.1 General . 31
5.5.3.2 Conducted Measurements for Radio Communication Devices . 31
5.5.3.2.1 Step 1: Start with the RBS Setup . 31
5.5.3.2.2 Step 2: Adding Interfering Signal Source . 31
5.5.3.2.3 Step 3: Degradation of Sensitivity Requirement . 31
5.5.3.2.4 Step 4: Test of Technical Wanted Performance Criteria . 31
5.5.3.2.5 Step 5: Measurement Assessment . 32
5.5.3.2.6 Step 6: Repetition of steps 4 and 5 . 32
5.5.3.3 Radiated Measurements for Radio Communication Devices with Power Limit . 32
5.5.3.3.1 Step 1: Start with the RBS Setup . 32
5.5.3.3.2 Step 2: Adding Interfering Signal Source . 32
5.5.3.3.3 Step 3: Degradation of Sensitivity Requirement . 32
5.5.3.3.4 Step 4: Test of Technical Wanted Performance Criteria . 33
5.5.3.3.5 Step 5: Measurement Assessment . 33
5.5.3.3.6 Step 6: Repetition of steps 4 and 5 . 33
5.5.3.4 Radiated Measurements for Radio Communication Devices with Distance Limit . 33
5.5.3.4.1 Step 1: Start with the RBS setup. 33
5.5.3.4.2 Step 2: Adding interfering signal source . 33
5.5.3.4.3 Step 3: Degradation of Sensitivity Requirement . 34
5.5.3.4.4 Step 4: Test of Technical Wanted Performance Criteria . 34
5.5.3.4.5 Step 5: Measurement Assessment . 34
5.5.3.4.6 Step 6: Repetition of steps 4 and 5 . 34
5.5.3.5 Radiated Measurements for Radiodetermination Applications with Distance Limit . 34
5.5.3.5.1 Step 1: Start with the RBS Setup . 34
5.5.3.5.2 Step 2: Adding interfering signal source . 34
5.5.3.5.3 Step 3: Degradation of Sensitivity Requirement . 35
5.5.3.5.4 Step 4: Test of Technical Wanted Performance Criteria . 36
5.5.3.5.5 Step 5: Measurement Assessment . 36
5.5.3.5.6 Step 6: Repetition of steps 4 and 5 . 36
5.5.3.6 Conducted Measurements for Radio Determination Devices . 36
5.5.3.6.1 Step 1: Start with the RBS Setup . 36
5.5.3.6.2 Step 2: Adding Interfering Signal Source . 36
5.5.3.6.3 Step 3: Degradation of Sensitivity Requirement . 36
5.5.3.6.4 Step 4: Test of Technical Performance Criteria . 37
5.5.3.6.5 Step 5: Measurement Assessment . 37
5.5.3.6.6 Step 6: Repetition of steps 4 and 5 . 37
Annex A (normative): Choose interferer for RBR . 38
A.1 Introduction . 38
A.2 Limits for the Interfering Signals . 39
A.2.1 Interferer within OFR . 39
A.2.1.0 Introduction. 39
A.2.1.1 Option 1 . 39
A.2.1.2 Option 2 . 39
ETSI
---------------------- Page: 6 ----------------------
SIST EN 303 883-2 V1.2.1:2021
5 ETSI EN 303 883-2 V1.2.1 (2021-02)
A.2.2 Interferer outside OFR . 40
A.3 Guidance to Setup the Power Level of the Interfering Signals @ EUT for RBR tests . 40
A.3.1 Radiated tests . 40
A.3.2 Conducted tests . 42
Annex B (informative): Guidance on Scaling Receiver Sensitivity . 43
B.1 General . 43
B.2 Scaling of power at the EUT . 43
B.3 Scaling distance . 44
Annex C (informative): Justification of receiver requirements from ETSI EG 203 336 . 45
C.1 General . 45
C.2 Justification . 45
C.3 Summary for the RBR requirement . 47
C.4 Justification RBS-requirement for radio determination devices . 48
Annex D (informative): Object and Radar Cross Section . 50
D.1 Wanted objects . 50
D.2 Direct Object Reflectors . 52
D.3 Delay Line Object Reflectors . 54
D.4 Electronic Object Reflectors . 54
D.5 Test Setup with Conventional RCS within Chamber . 55
D.6 Test Setup with Radar Object Generator . 56
D.6.1 General . 56
Annex E (informative): Change History . 58
History . 59
ETSI
---------------------- Page: 7 ----------------------
SIST EN 303 883-2 V1.2.1:2021
6 ETSI EN 303 883-2 V1.2.1 (2021-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and
Radio spectrum Matters (ERM).
The present document is part 2 of a multi-part deliverable covering Short Range Devices (SRD) and Ultra Wide Band
(UWB), as identified below:
Part 1: "Measurement techniques for transmitter requirements";
Part 2: "Measurement techniques for receiver requirements".
National transposition dates
Date of adoption of this EN: 22 February 2021
Date of latest announcement of this EN (doa): 31 May 2021
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2021
Date of withdrawal of any conflicting National Standard (dow): 30 November 2021
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 8 ----------------------
SIST EN 303 883-2 V1.2.1:2021
7 ETSI EN 303 883-2 V1.2.1 (2021-02)
Introduction
The present document provides measurement procedures for receiver requirements to address the spectrum efficiency
requirements of the RED [i.10].
The basis for this RX concept was developed by ETSI during two Special Task Forces.
First Special Task Force: ETSI STF 494; Update of the UWB related Harmonised Standards covering the essential
requirements of article 3.2 of the RED [i.10].
The STF 494:
• Started: 2015-05-25
• Ended: 2016-03-31
Outcome:
• ETSI TS 103 361 [i.4]
The second Special Task Force: ETSI STF 541; Signal interferer handling, a new RX requirement to cover the
essential requirements of article 3.2 of the RED [i.10], was a continuation to implement and consider comments
received after the publication of the ETSI TS 103 361 [i.4].
The STF 541:
• Started: 2017-10-06
• Ended: 2019-05-31
Outcome:
• ETSI TR 103 566 [i.2]
• ETSI TS 103 567 [i.3]
There is no specification of receiver parameter values within the present document. These values will be derived from
technical specification defined by the responsible ETSI Technical Committees and/or the findings of regulatory studies
conducted by the relevant bodies like CEPT ECC WG SE. The limits/values for the baseline RX-conformance
requirements will be specified in the related standard.
In addition to the two receiver baseline requirements it can be necessary that the RX spurious emission requirement
could be a further RX requirement in the related standard. This could be necessary if the EUT has a receive only mode
or if it is not collocated to the transmitter. The present document specifies the receiver spurious emission requirement
and the corresponding test and measurement procedure in clause 5.2.
The present document provides practical information and guidance for the compliance receiver tests of UWB and Short
Range technology and devices.
It is recommended that, in drafting the related standards, a thorough analysis is conducted on all possible applicable
receiver parameters (see annex C), selecting the most appropriate RX-requirements and having a robust reasoning for
those that are disregarded.
ETSI
---------------------- Page: 9 ----------------------
SIST EN 303 883-2 V1.2.1:2021
8 ETSI EN 303 883-2 V1.2.1 (2021-02)
1 Scope
The present document provides measurement procedures for receiver requirements to address the spectrum efficiency
requirements of the RED [i.10].
The baseline receiver concept is a set of two parameters given in clause 5 of the present document providing guidance
for HS development, which can be further refined by the responsible TB.
Baseline receiver concept comprises the following parameters:
• Receiver Baseline Sensitivity (RBS); and
• Receiver Baseline Resilience (RBR).
The Baseline receiver concept is a further development of the signal interferer handling concept, see ETSI
TS 103 361 [i.4].
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found
...
Final draft ETSI EN 303 883-2 V1.2.1 (2020-12)
EUROPEAN STANDARD
Short Range Devices (SRD) and
Ultra Wide Band (UWB);
Part 2: Measurement techniques
for receiver requirements
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 303 883-2 V1.2.1 (2020-12)
Reference
REN/ERM-TGUWB-149-2
Keywords
measurement, receiver, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 303 883-2 V1.2.1 (2020-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 11
4 General . 12
5 Receiver Requirements. 12
5.1 General Guidance on RX measurement . 12
5.2 Receiver Spurious Emissions . 12
5.2.1 Description . 12
5.2.2 Limits . 12
5.2.3 Conformance. 13
5.2.3.1 General . 13
5.2.3.2 Step 1: Measurement with Peak Detector . 13
5.2.3.3 Step 2: Measurement with RMS Detector . 14
5.3 Use-Case Specific Input Parameters for Receiver Baseline Requirements . 14
5.3.1 Introduction. 14
5.3.2 Technical Wanted Performance Criteria . 15
5.3.3 Examples of Use-Case Specific Input Parameter for Receiver Tests . 15
5.3.3.1 Communication/Location Tracking Device . 15
5.3.3.2 Radio Determination Device (non-contact based) . 16
5.3.3.3 Material contact-based radio determination device . 18
5.4 Receiver Baseline Sensitivity (RBS) . 20
5.4.1 Description . 20
5.4.2 Limits . 20
5.4.3 Conformance. 21
5.4.3.1 General . 21
5.4.3.2 Conducted measurements for radio communication devices . 21
5.4.3.2.0 General . 21
5.4.3.2.1 Step 1: Technical Wanted Performance Criteria . 21
5.4.3.2.2 Step 2: Sensitivity Requirement (Power) . 21
5.4.3.2.3 Step 3: Measurement Procedure . 21
5.4.3.2.4 Step 4: Technical Wanted Performance Criteria Assessment . 23
5.4.3.3 Radiated Measurements for Radio Communication Devices with Power Limit . 23
5.4.3.3.0 General . 23
5.4.3.3.1 Step 1: Technical Wanted Performance Criteria . 23
5.4.3.3.2 Step 2: Sensitivity Requirement (Power) . 23
5.4.3.3.3 Step 3: Measurement Procedure . 23
5.4.3.3.4 Step 4: Technical Wanted Performance Criteria Assessment . 25
5.4.3.4 Radiated measurements for radio communication devices with distance limit . 25
5.4.3.4.0 General . 25
5.4.3.4.1 Step 1: Technical Wanted Performance Criteria . 25
5.4.3.4.2 Step 2: Sensitivity Requirement (Distance) . 25
5.4.3.4.3 Step 3: Measurement Procedure . 26
5.4.3.4.4 Step 4: Technical Wanted Performance Criteria Assessment . 26
5.4.3.5 Radiated Measurements for Radiodetermination Applications with Distance Limit . 26
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 303 883-2 V1.2.1 (2020-12)
5.4.3.5.0 General . 26
5.4.3.5.1 Step 1: Technical Performance Criteria . 26
5.4.3.5.2 Step 2: Sensitivity Requirement (Distance) . 27
5.4.3.5.3 Step 3: Measurement Procedure . 27
5.4.3.5.4 Step 4: Technical Wanted Performance Criteria Assessment . 28
5.4.3.6 Conducted measurements for radio determination devices . 28
5.4.3.6.0 General . 28
5.4.3.6.1 Step 1: Technical Wanted Performance Criteria . 28
5.4.3.6.2 Step 2: Sensitivity Requirement (Power) . 28
5.4.3.6.3 Step 3: Measurement Procedure . 29
5.4.3.6.4 Step 4: Technical Wanted Performance Criteria Assessment . 30
5.5 Receiver Baseline Resilience (RBR) . 30
5.5.1 Description . 30
5.5.2 RBR Requirements . 30
5.5.2.1 Interferer test signal. 30
5.5.2.2 RBR wanted performance criteria . 30
5.5.3 Conformance. 31
5.5.3.1 General . 31
5.5.3.2 Conducted Measurements for Radio Communication Devices . 31
5.5.3.2.1 Step 1: Start with the RBS Setup . 31
5.5.3.2.2 Step 2: Adding Interfering Signal Source . 31
5.5.3.2.3 Step 3: Degradation of Sensitivity Requirement . 31
5.5.3.2.4 Step 4: Test of Technical Wanted Performance Criteria . 31
5.5.3.2.5 Step 5: Measurement Assessment . 32
5.5.3.2.6 Step 6: Repetition of steps 4 and 5 . 32
5.5.3.3 Radiated Measurements for Radio Communication Devices with Power Limit . 32
5.5.3.3.1 Step 1: Start with the RBS Setup . 32
5.5.3.3.2 Step 2: Adding Interfering Signal Source . 32
5.5.3.3.3 Step 3: Degradation of Sensitivity Requirement . 32
5.5.3.3.4 Step 4: Test of Technical Wanted Performance Criteria . 33
5.5.3.3.5 Step 5: Measurement Assessment . 33
5.5.3.3.6 Step 6: Repetition of steps 4 and 5 . 33
5.5.3.4 Radiated Measurements for Radio Communication Devices with Distance Limit . 33
5.5.3.4.1 Step 1: Start with the RBS setup. 33
5.5.3.4.2 Step 2: Adding interfering signal source . 33
5.5.3.4.3 Step 3: Degradation of Sensitivity Requirement . 34
5.5.3.4.4 Step 4: Test of Technical Wanted Performance Criteria . 34
5.5.3.4.5 Step 5: Measurement Assessment . 34
5.5.3.4.6 Step 6: Repetition of steps 4 and 5 . 34
5.5.3.5 Radiated Measurements for Radiodetermination Applications with Distance Limit . 34
5.5.3.5.1 Step 1: Start with the RBS Setup . 34
5.5.3.5.2 Step 2: Adding interfering signal source . 34
5.5.3.5.3 Step 3: Degradation of Sensitivity Requirement . 35
5.5.3.5.4 Step 4: Test of Technical Wanted Performance Criteria . 36
5.5.3.5.5 Step 5: Measurement Assessment . 36
5.5.3.5.6 Step 6: Repetition of steps 4 and 5 . 36
5.5.3.6 Conducted Measurements for Radio Determination Devices . 36
5.5.3.6.1 Step 1: Start with the RBS Setup . 36
5.5.3.6.2 Step 2: Adding Interfering Signal Source . 36
5.5.3.6.3 Step 3: Degradation of Sensitivity Requirement . 36
5.5.3.6.4 Step 4: Test of Technical Performance Criteria . 37
5.5.3.6.5 Step 5: Measurement Assessment . 37
5.5.3.6.6 Step 6: Repetition of steps 4 and 5 . 37
Annex A (normative): Choose interferer for RBR . 38
A.1 Introduction . 38
A.2 Limits for the Interfering Signals . 39
A.2.1 Interferer within OFR . 39
A.2.1.0 Introduction. 39
A.2.1.1 Option 1 . 39
A.2.1.2 Option 2 . 39
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 303 883-2 V1.2.1 (2020-12)
A.2.2 Interferer outside OFR . 40
A.3 Guidance to Setup the Power Level of the Interfering Signals @ EUT for RBR tests . 40
A.3.1 Radiated tests . 40
A.3.2 Conducted tests . 42
Annex B (informative): Guidance on Scaling Receiver Sensitivity . 43
B.1 General . 43
B.2 Scaling of power at the EUT . 43
B.3 Scaling distance . 44
Annex C (informative): Justification of receiver requirements from ETSI EG 203 336 . 45
C.1 General . 45
C.2 Justification . 45
C.3 Summary for the RBR requirement . 47
C.4 Justification RBS-requirement for radio determination devices . 48
Annex D (informative): Object and Radar Cross Section . 50
D.1 Wanted objects . 50
D.2 Direct Object Reflectors . 52
D.3 Delay Line Object Reflectors . 54
D.4 Electronic Object Reflectors . 54
D.5 Test Setup with Conventional RCS within Chamber . 55
D.6 Test Setup with Radar Object Generator . 56
D.6.1 General . 56
Annex E (informative): Change History . 58
History . 59
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 303 883-2 V1.2.1 (2020-12)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This final draft European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the ETSI standards EN
Approval Procedure.
The present document is part 2 of a multi-part deliverable covering Short Range Devices (SRD) and Ultra Wide Band
(UWB), as identified below:
Part 1: "Measurement techniques for transmitter requirements";
Part 2: "Measurement techniques for receiver requirements".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 303 883-2 V1.2.1 (2020-12)
Introduction
The present document provides measurement procedures for receiver requirements to address the spectrum efficiency
requirements of the RED [i.10].
The basis for this RX concept was developed by ETSI during two Special Task Forces.
First Special Task Force: ETSI STF 494; Update of the UWB related Harmonised Standards covering the essential
requirements of article 3.2 of the RED [i.10].
The STF 494:
• Started: 2015-05-25
• Ended: 2016-03-31
Outcome:
• ETSI TS 103 361 [i.4]
The second Special Task Force: ETSI STF 541; Signal interferer handling, a new RX requirement to cover the
essential requirements of article 3.2 of the RED [i.10], was a continuation to implement and consider comments
received after the publication of the ETSI TS 103 361 [i.4].
The STF 541:
• Started: 2017-10-06
• Ended: 2019-05-31
Outcome:
• ETSI TR 103 566 [i.2]
• ETSI TS 103 567 [i.3]
There is no specification of receiver parameter values within the present document. These values will be derived from
technical specification defined by the responsible ETSI Technical Committees and/or the findings of regulatory studies
conducted by the relevant bodies like CEPT ECC WG SE. The limits/values for the baseline RX-conformance
requirements will be specified in the related standard.
In addition to the two receiver baseline requirements it can be necessary that the RX spurious emission requirement
could be a further RX requirement in the related standard. This could be necessary if the EUT has a receive only mode
or if it is not collocated to the transmitter. The present document specifies the receiver spurious emission requirement
and the corresponding test and measurement procedure in clause 5.2.
The present document provides practical information and guidance for the compliance receiver tests of UWB and Short
Range technology and devices.
It is recommended that, in drafting the related standards, a thorough analysis is conducted on all possible applicable
receiver parameters (see annex C), selecting the most appropriate RX-requirements and having a robust reasoning for
those that are disregarded.
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 303 883-2 V1.2.1 (2020-12)
1 Scope
The present document provides measurement procedures for receiver requirements to address the spectrum efficiency
requirements of the RED [i.10].
The baseline receiver concept is a set of two parameters given in clause 5 of the present document providing guidance
for HS development, which can be further refined by the responsible TB.
Baseline receiver concept comprises the following parameters:
• Receiver Baseline Sensitivity (RBS); and
• Receiver Baseline Resilience (RBR).
The Baseline receiver concept is a further development of the signal interferer handling concept, see ETSI
TS 103 361 [i.4].
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the ap
...
Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
EUROPEAN STANDARD
Short Range Devices (SRD) and
Ultra Wide Band (UWB);
Part 2: Measurement techniques
for receiver requirements
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
Reference
REN/ERM-TGUWB-149-2
Keywords
measurement, receiver, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 General . 11
5 Receiver Requirements. 12
5.1 General Guidance on RX measurement . 12
5.2 Receiver Spurious Emissions . 12
5.2.1 Description . 12
5.2.2 Limits . 12
5.2.3 Conformance. 13
5.2.3.1 General . 13
5.2.3.2 Step 1: Measurement with Peak Detector . 13
5.2.3.3 Step 2: Measurement with RMS Detector . 13
5.3 Use-Case Specific Input Parameters for Receiver Baseline Requirements . 14
5.3.1 Introduction. 14
5.3.2 Technical Wanted Performance Criteria . 14
5.3.3 Examples of Use-Case Specific Input Parameter for Receiver Tests . 15
5.3.3.1 Communication/Location Tracking Device . 15
5.3.3.2 Radio Determination Device (non-contact based) . 15
5.3.3.3 Material contact-based radio determination device . 17
5.4 Receiver Baseline Sensitivity (RBS) . 19
5.4.1 Description . 19
5.4.2 Limits . 19
5.4.3 Conformance. 20
5.4.3.1 General . 20
5.4.3.2 Conducted measurements for radio communication devices . 20
5.4.3.2.0 General . 20
5.4.3.2.1 Step 1: Technical Wanted Performance Criteria . 20
5.4.3.2.2 Step 2: Sensitivity Requirement (Power) . 20
5.4.3.2.3 Step 3: Measurement Procedure . 20
5.4.3.2.4 Step 4: Technical Wanted Performance Criteria Assessment . 22
5.4.3.3 Radiated Measurements for Radio Communication Devices with Power Limit . 22
5.4.3.3.0 General . 22
5.4.3.3.1 Step 1: Technical Wanted Performance Criteria . 22
5.4.3.3.2 Step 2: Sensitivity Requirement (Power) . 22
5.4.3.3.3 Step 3: Measurement Procedure . 22
5.4.3.3.4 Step 4: Technical Wanted Performance Criteria Assessment . 24
5.4.3.4 Radiated measurements for radio communication devices with distance limit . 24
5.4.3.4.0 General . 24
5.4.3.4.1 Step 1: Technical Wanted Performance Criteria . 24
5.4.3.4.2 Step 2: Sensitivity Requirement (Distance) . 24
5.4.3.4.3 Step 3: Measurement Procedure . 24
5.4.3.4.4 Step 4: Technical Wanted Performance Criteria Assessment . 25
5.4.3.5 Radiated Measurements for Radiodetermination Applications with Distance Limit . 25
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
5.4.3.5.0 General . 25
5.4.3.5.1 Step 1: Technical Performance Criteria . 25
5.4.3.5.2 Step 2: Sensitivity Requirement (Distance) . 26
5.4.3.5.3 Step 3: Measurement Procedure . 26
5.4.3.5.4 Step 4: Technical Wanted Performance Criteria Assessment . 27
5.4.3.6 Conducted measurements for radio determination devices . 27
5.4.3.6.0 General . 27
5.4.3.6.1 Step 1: Technical Wanted Performance Criteria . 27
5.4.3.6.2 Step 2: Sensitivity Requirement (Power) . 27
5.4.3.6.3 Step 3: Measurement Procedure . 28
5.4.3.6.4 Step 4: Technical Wanted Performance Criteria Assessment . 29
5.5 Receiver Baseline Resilience (RBR) . 29
5.5.1 Description . 29
5.5.2 RBR Requirements . 29
5.5.2.1 Interferer test signal. 29
5.5.2.2 RBR wanted performance criteria . 29
5.5.3 Conformance. 30
5.5.3.1 General . 30
5.5.3.2 Conducted Measurements for Radio Communication Devices . 30
5.5.3.2.1 Step 1: Start with the RBS Setup . 30
5.5.3.2.2 Step 2: Adding Interfering Signal Source . 30
5.5.3.2.3 Step 3: Degradation of Sensitivity Requirement . 30
5.5.3.2.4 Step 4: Test of Technical Wanted Performance Criteria . 30
5.5.3.2.5 Step 5: Measurement Assessment . 31
5.5.3.2.6 Step 6: Repetition of steps 4 and 5 . 31
5.5.3.3 Radiated Measurements for Radio Communication Devices with Power Limit . 31
5.5.3.3.1 Step 1: Start with the RBS Setup . 31
5.5.3.3.2 Step 2: Adding Interfering Signal Source . 31
5.5.3.3.3 Step 3: Degradation of Sensitivity Requirement . 31
5.5.3.3.4 Step 4: Test of Technical Wanted Performance Criteria . 32
5.5.3.3.5 Step 5: Measurement Assessment . 32
5.5.3.3.6 Step 6: Repetition of steps 4 and 5 . 32
5.5.3.4 Radiated Measurements for Radio Communication Devices with Distance Limit . 32
5.5.3.4.1 Step 1: Start with the RBS setup. 32
5.5.3.4.2 Step 2: Adding interfering signal source . 32
5.5.3.4.3 Step 3: Degradation of Sensitivity Requirement . 33
5.5.3.4.4 Step 4: Test of Technical Wanted Performance Criteria . 33
5.5.3.4.5 Step 5: Measurement Assessment . 33
5.5.3.4.6 Step 6: Repetition of steps 4 and 5 . 33
5.5.3.5 Radiated Measurements for Radiodetermination Applications with Distance Limit . 33
5.5.3.5.1 Step 1: Start with the RBS Setup . 33
5.5.3.5.2 Step 2: Adding interfering signal source . 33
5.5.3.5.3 Step 3: Degradation of Sensitivity Requirement . 34
5.5.3.5.4 Step 4: Test of Technical Wanted Performance Criteria . 35
5.5.3.5.5 Step 5: Measurement Assessment . 35
5.5.3.5.6 Step 6: Repetition of steps 4 and 5 . 35
5.5.3.6 Conducted Measurements for Radio Determination Devices . 35
5.5.3.6.1 Step 1: Start with the RBS Setup . 35
5.5.3.6.2 Step 2: Adding Interfering Signal Source . 35
5.5.3.6.3 Step 3: Degradation of Sensitivity Requirement . 35
5.5.3.6.4 Step 4: Test of Technical Performance Criteria . 36
5.5.3.6.5 Step 5: Measurement Assessment . 36
5.5.3.6.6 Step 6: Repetition of steps 4 and 5 . 36
Annex A (normative): Choose interferer for RBR . 37
A.1 Introduction . 37
A.2 Limits for the Interfering Signals . 38
A.2.1 Interferer within OFR . 38
A.2.1.0 Introduction. 38
A.2.1.1 Option 1 . 38
A.2.1.2 Option 2 . 38
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
A.2.2 Interferer outside OFR . 39
A.3 Guidance to Setup the Power Level of the Interfering Signals @ EUT for RBR tests . 39
A.3.1 Radiated tests . 39
A.3.2 Conducted tests . 41
Annex B (informative): Guidance on Scaling Receiver Sensitivity . 42
B.1 General . 42
B.2 Scaling of power at the EUT . 42
B.3 Scaling distance . 42
Annex C (informative): Justification of receiver requirements from ETSI EG 203 336 . 44
C.1 General . 44
C.2 Justification . 44
C.3 Summary for the RBR requirement . 46
C.4 Justification RBS-requirement for radio determination devices . 47
Annex D (informative): Object and Radar Cross Section . 49
D.1 Wanted objects . 49
D.2 Direct Object Reflectors . 51
D.3 Delay Line Object Reflectors . 53
D.4 Electronic Object Reflectors . 53
D.5 Test Setup with Conventional RCS within Chamber . 54
D.6 Test Setup with Radar Object Generator . 55
D.6.1 General . 55
Annex E (informative): Change History . 57
History . 58
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility
and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 2 of a multi-part deliverable covering Short Range Devices (SRD) and Ultra Wide Band
(UWB), as identified below:
Part 1: "Measurement techniques for transmitter requirements";
Part 2: " Measurement techniques for receiver requirements".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
Introduction
The present document provides measurement procedures for receiver requirements to address the spectrum efficiency
requirements of the RED [i.10].
The basis for this RX concept was developed by ETSI during two Special Task Forces.
First Special Task Force: ETSI STF 494; Update of the UWB related Harmonised Standards covering the essential
requirements of article 3.2 of the RED [i.10].
The STF 494:
• Started: 2015-05-25
• Ended: 2016-03-31
Outcome:
ETSI TS 103 361 [i.4]
The second Special Task Force: ETSI STF 541; Signal interferer handling, a new RX requirement to cover the
essential requirements of article 3.2 of the RED [i.10], was a continuation to implement and consider comments
received after the publication of the ETSI TS 103 361 [i.4].
The STF 541:
• Started: 2017-10-06
• Ended: 2019-05-31
Outcome:
• ETSI TR 103 566 [i.2]
• ETSI TS 103 567 [i.3]
There is no specification of receiver parameter values within the present document. These values will be derived from
technical specification defined by the responsible ETSI Technical Committees and/or the findings of regulatory studies
conducted by the relevant bodies like CEPT ECC WG SE. The limits/values for the baseline RX-conformance
requirements will be specified in the related standard.
In addition to the two receiver baseline requirements it can be necessary that the RX spurious emission requirement
could be a further RX requirement in the related standard. This could be necessary if the EUT has a receive only mode
or if it is not collocated to the transmitter. The present document specifies the receiver spurious emission requirement
and the corresponding test and measurement procedure in clause 5.2.
The present document provides practical information and guidance for the compliance receiver tests of UWB and Short
Range technology and devices.
It is recommended that, in drafting the related standards, a thorough analysis is conducted on all possible applicable
receiver parameters (see annex C), selecting the most appropriate RX-requirements and having a robust reasoning for
those that are disregarded.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
1 Scope
The present document provides measurement procedures for receiver requirements to address the spectrum efficiency
requirements of the RED [i.10].
The baseline receiver concept is a set of two parameters given in clause 5 of the present document providing guidance
for HS development, which can be further refined by the responsible TB.
Baseline receiver concept comprises the following parameters:
• Receiver Baseline Sensitivity (RBS); and
• Receiver Baseline Resilience (RBR).
The Baseline receiver concept is a further development of the signal interferer handling concept, see ETSI
TS 103 361 [i.4].
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EG 2
...
SLOVENSKI STANDARD
oSIST prEN 303 883-2 V1.2.0:2020
01-september-2020
Naprave kratkega dosega (SRD) in ultra širokopasovna (UWB) tehnologija - 2. del:
Merilne tehnike za zahteve sprejemnika
Short Range Devices (SRD) and Ultra Wide Band (UWB) - Part 2: Measurement
techniques for receiver requirements
Ta slovenski standard je istoveten z: ETSI EN 303 883-2 V1.2.0 (2020-07)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
oSIST prEN 303 883-2 V1.2.0:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 303 883-2 V1.2.0:2020
---------------------- Page: 2 ----------------------
oSIST prEN 303 883-2 V1.2.0:2020
Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
EUROPEAN STANDARD
Short Range Devices (SRD) and
Ultra Wide Band (UWB);
Part 2: Measurement techniques
for receiver requirements
---------------------- Page: 3 ----------------------
oSIST prEN 303 883-2 V1.2.0:2020
2 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
Reference
REN/ERM-TGUWB-149-2
Keywords
measurement, receiver, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 303 883-2 V1.2.0:2020
3 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 General . 11
5 Receiver Requirements. 12
5.1 General Guidance on RX measurement . 12
5.2 Receiver Spurious Emissions . 12
5.2.1 Description . 12
5.2.2 Limits . 12
5.2.3 Conformance. 13
5.2.3.1 General . 13
5.2.3.2 Step 1: Measurement with Peak Detector . 13
5.2.3.3 Step 2: Measurement with RMS Detector . 13
5.3 Use-Case Specific Input Parameters for Receiver Baseline Requirements . 14
5.3.1 Introduction. 14
5.3.2 Technical Wanted Performance Criteria . 14
5.3.3 Examples of Use-Case Specific Input Parameter for Receiver Tests . 15
5.3.3.1 Communication/Location Tracking Device . 15
5.3.3.2 Radio Determination Device (non-contact based) . 15
5.3.3.3 Material contact-based radio determination device . 17
5.4 Receiver Baseline Sensitivity (RBS) . 19
5.4.1 Description . 19
5.4.2 Limits . 19
5.4.3 Conformance. 20
5.4.3.1 General . 20
5.4.3.2 Conducted measurements for radio communication devices . 20
5.4.3.2.0 General . 20
5.4.3.2.1 Step 1: Technical Wanted Performance Criteria . 20
5.4.3.2.2 Step 2: Sensitivity Requirement (Power) . 20
5.4.3.2.3 Step 3: Measurement Procedure . 20
5.4.3.2.4 Step 4: Technical Wanted Performance Criteria Assessment . 22
5.4.3.3 Radiated Measurements for Radio Communication Devices with Power Limit . 22
5.4.3.3.0 General . 22
5.4.3.3.1 Step 1: Technical Wanted Performance Criteria . 22
5.4.3.3.2 Step 2: Sensitivity Requirement (Power) . 22
5.4.3.3.3 Step 3: Measurement Procedure . 22
5.4.3.3.4 Step 4: Technical Wanted Performance Criteria Assessment . 24
5.4.3.4 Radiated measurements for radio communication devices with distance limit . 24
5.4.3.4.0 General . 24
5.4.3.4.1 Step 1: Technical Wanted Performance Criteria . 24
5.4.3.4.2 Step 2: Sensitivity Requirement (Distance) . 24
5.4.3.4.3 Step 3: Measurement Procedure . 24
5.4.3.4.4 Step 4: Technical Wanted Performance Criteria Assessment . 25
5.4.3.5 Radiated Measurements for Radiodetermination Applications with Distance Limit . 25
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 303 883-2 V1.2.0:2020
4 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
5.4.3.5.0 General . 25
5.4.3.5.1 Step 1: Technical Performance Criteria . 25
5.4.3.5.2 Step 2: Sensitivity Requirement (Distance) . 26
5.4.3.5.3 Step 3: Measurement Procedure . 26
5.4.3.5.4 Step 4: Technical Wanted Performance Criteria Assessment . 27
5.4.3.6 Conducted measurements for radio determination devices . 27
5.4.3.6.0 General . 27
5.4.3.6.1 Step 1: Technical Wanted Performance Criteria . 27
5.4.3.6.2 Step 2: Sensitivity Requirement (Power) . 27
5.4.3.6.3 Step 3: Measurement Procedure . 28
5.4.3.6.4 Step 4: Technical Wanted Performance Criteria Assessment . 29
5.5 Receiver Baseline Resilience (RBR) . 29
5.5.1 Description . 29
5.5.2 RBR Requirements . 29
5.5.2.1 Interferer test signal. 29
5.5.2.2 RBR wanted performance criteria . 29
5.5.3 Conformance. 30
5.5.3.1 General . 30
5.5.3.2 Conducted Measurements for Radio Communication Devices . 30
5.5.3.2.1 Step 1: Start with the RBS Setup . 30
5.5.3.2.2 Step 2: Adding Interfering Signal Source . 30
5.5.3.2.3 Step 3: Degradation of Sensitivity Requirement . 30
5.5.3.2.4 Step 4: Test of Technical Wanted Performance Criteria . 30
5.5.3.2.5 Step 5: Measurement Assessment . 31
5.5.3.2.6 Step 6: Repetition of steps 4 and 5 . 31
5.5.3.3 Radiated Measurements for Radio Communication Devices with Power Limit . 31
5.5.3.3.1 Step 1: Start with the RBS Setup . 31
5.5.3.3.2 Step 2: Adding Interfering Signal Source . 31
5.5.3.3.3 Step 3: Degradation of Sensitivity Requirement . 31
5.5.3.3.4 Step 4: Test of Technical Wanted Performance Criteria . 32
5.5.3.3.5 Step 5: Measurement Assessment . 32
5.5.3.3.6 Step 6: Repetition of steps 4 and 5 . 32
5.5.3.4 Radiated Measurements for Radio Communication Devices with Distance Limit . 32
5.5.3.4.1 Step 1: Start with the RBS setup. 32
5.5.3.4.2 Step 2: Adding interfering signal source . 32
5.5.3.4.3 Step 3: Degradation of Sensitivity Requirement . 33
5.5.3.4.4 Step 4: Test of Technical Wanted Performance Criteria . 33
5.5.3.4.5 Step 5: Measurement Assessment . 33
5.5.3.4.6 Step 6: Repetition of steps 4 and 5 . 33
5.5.3.5 Radiated Measurements for Radiodetermination Applications with Distance Limit . 33
5.5.3.5.1 Step 1: Start with the RBS Setup . 33
5.5.3.5.2 Step 2: Adding interfering signal source . 33
5.5.3.5.3 Step 3: Degradation of Sensitivity Requirement . 34
5.5.3.5.4 Step 4: Test of Technical Wanted Performance Criteria . 35
5.5.3.5.5 Step 5: Measurement Assessment . 35
5.5.3.5.6 Step 6: Repetition of steps 4 and 5 . 35
5.5.3.6 Conducted Measurements for Radio Determination Devices . 35
5.5.3.6.1 Step 1: Start with the RBS Setup . 35
5.5.3.6.2 Step 2: Adding Interfering Signal Source . 35
5.5.3.6.3 Step 3: Degradation of Sensitivity Requirement . 35
5.5.3.6.4 Step 4: Test of Technical Performance Criteria . 36
5.5.3.6.5 Step 5: Measurement Assessment . 36
5.5.3.6.6 Step 6: Repetition of steps 4 and 5 . 36
Annex A (normative): Choose interferer for RBR . 37
A.1 Introduction . 37
A.2 Limits for the Interfering Signals . 38
A.2.1 Interferer within OFR . 38
A.2.1.0 Introduction. 38
A.2.1.1 Option 1 . 38
A.2.1.2 Option 2 . 38
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 303 883-2 V1.2.0:2020
5 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
A.2.2 Interferer outside OFR . 39
A.3 Guidance to Setup the Power Level of the Interfering Signals @ EUT for RBR tests . 39
A.3.1 Radiated tests . 39
A.3.2 Conducted tests . 41
Annex B (informative): Guidance on Scaling Receiver Sensitivity . 42
B.1 General . 42
B.2 Scaling of power at the EUT . 42
B.3 Scaling distance . 42
Annex C (informative): Justification of receiver requirements from ETSI EG 203 336 . 44
C.1 General . 44
C.2 Justification . 44
C.3 Summary for the RBR requirement . 46
C.4 Justification RBS-requirement for radio determination devices . 47
Annex D (informative): Object and Radar Cross Section . 49
D.1 Wanted objects . 49
D.2 Direct Object Reflectors . 51
D.3 Delay Line Object Reflectors . 53
D.4 Electronic Object Reflectors . 53
D.5 Test Setup with Conventional RCS within Chamber . 54
D.6 Test Setup with Radar Object Generator . 55
D.6.1 General . 55
Annex E (informative): Change History . 57
History . 58
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 303 883-2 V1.2.0:2020
6 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility
and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 2 of a multi-part deliverable covering Short Range Devices (SRD) and Ultra Wide Band
(UWB), as identified below:
Part 1: "Measurement techniques for transmitter requirements";
Part 2: " Measurement techniques for receiver requirements".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 303 883-2 V1.2.0:2020
7 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
Introduction
The present document provides measurement procedures for receiver requirements to address the spectrum efficiency
requirements of the RED [i.10].
The basis for this RX concept was developed by ETSI during two Special Task Forces.
First Special Task Force: ETSI STF 494; Update of the UWB related Harmonised Standards covering the essential
requirements of article 3.2 of the RED [i.10].
The STF 494:
• Started: 2015-05-25
• Ended: 2016-03-31
Outcome:
ETSI TS 103 361 [i.4]
The second Special Task Force: ETSI STF 541; Signal interferer handling, a new RX requirement to cover the
essential requirements of article 3.2 of the RED [i.10], was a continuation to implement and consider comments
received after the publication of the ETSI TS 103 361 [i.4].
The STF 541:
• Started: 2017-10-06
• Ended: 2019-05-31
Outcome:
• ETSI TR 103 566 [i.2]
• ETSI TS 103 567 [i.3]
There is no specification of receiver parameter values within the present document. These values will be derived from
technical specification defined by the responsible ETSI Technical Committees and/or the findings of regulatory studies
conducted by the relevant bodies like CEPT ECC WG SE. The limits/values for the baseline RX-conformance
requirements will be specified in the related standard.
In addition to the two receiver baseline requirements it can be necessary that the RX spurious emission requirement
could be a further RX requirement in the related standard. This could be necessary if the EUT has a receive only mode
or if it is not collocated to the transmitter. The present document specifies the receiver spurious emission requirement
and the corresponding test and measurement procedure in clause 5.2.
The present document provides practical information and guidance for the compliance receiver tests of UWB and Short
Range technology and devices.
It is recommended that, in drafting the related standards, a thorough analysis is conducted on all possible applicable
receiver parameters (see annex C), selecting the most appropriate RX-requirements and having a robust reasoning for
those that are disregarded.
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 303 883-2 V1.2.0:2020
8 Draft ETSI EN 303 883-2 V1.2.0 (2020-07)
1 Scope
The present document provides measurement procedures for receiver requirements to address the spectrum efficiency
requirements of the RED [i.10].
The baseline receiver concept is a set of two parameters given in clause 5 of the present document providing guidance
for HS development, which can be further refined by the responsible TB.
Baseline receiver concept comprises the following parameters:
• Receiver Baseline Sensitivity (RBS); and
• Receiver Baseline Resilience (RBR).
The Baseline receiver concept is a further development of the signal interferer handling concept, see ETSI
TS 103 361 [i.4].
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.