SIST EN ISO 8986-2:1999

Plastics - Polybutene (PB) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8986-2:1995)

Kunststoffe - Polybuten (PB) Formmassen - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 8986-2:1995)

Plastiques - Polybutene (PB) pour moulage et extrusion - Partie 2: Préparation et détermination des propriétés (ISO 8986-2:1995)

Polimerni materiali – Materiali za oblikovanje in ekstrudiranje iz polibutena – 2. del: Priprava preskušancev in določevanje lastnosti (ISO 8986-2:1995)

General Information

• Status: Withdrawn
• Publication Date: 30-Apr-1999
• Withdrawal Date: 19-Jan-2010
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 04-Jan-2010
• Due Date: 27-Jan-2010
• Completion Date: 20-Jan-2010
• Ref Project: EN ISO 8986-2:1995 - Plastics - Polybutene (PB) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8986-2:1995)

Relations

• Replaced By: SIST EN ISO 8986-2:2010 - Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8986-2:2009)
• Effective Date: 01-Feb-2010
• Amended By: SIST EN ISO 8986-2:1999/A1:2000 - Plastics - Polybutene (PB) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties - Amendment 1 (ISO 8986-2:1995/AM 1:2000)
• Effective Date: 22-Dec-2008
• Amended By: SIST EN ISO 8986-2:1999/A1:2000 - Plastics - Polybutene (PB) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties - Amendment 1 (ISO 8986-2:1995/AM 1:2000)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 8986-2:1999
01-maj-1999
3ROLPHUQLPDWHULDOL±0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]SROLEXWHQD±GHO
3ULSUDYDSUHVNXãDQFHYLQGRORþHYDQMHODVWQRVWL,62
Plastics - Polybutene (PB) moulding and extrusion materials - Part 2: Preparation of test
specimens and determination of properties (ISO 8986-2:1995)
Kunststoffe - Polybuten (PB) Formmassen - Teil 2: Herstellung von Probekörpern und
Bestimmung von Eigenschaften (ISO 8986-2:1995)
Plastiques - Polybutene (PB) pour moulage et extrusion - Partie 2: Préparation et
détermination des propriétés (ISO 8986-2:1995)
Ta slovenski standard je istoveten z: EN ISO 8986-2:1995
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 8986-2:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8986-2:1999

---------------------- Page: 2 ----------------------

SIST EN ISO 8986-2:1999

---------------------- Page: 3 ----------------------

SIST EN ISO 8986-2:1999

---------------------- Page: 4 ----------------------

SIST EN ISO 8986-2:1999

---------------------- Page: 5 ----------------------

SIST EN ISO 8986-2:1999

---------------------- Page: 6 ----------------------

SIST EN ISO 8986-2:1999
INTERNATIONAL
IS0
STANDARD
8986-2
First edition
1995-09-01
Plastics - Polybutene (PB) moulding and
extrusion materials -
Part 2:
Preparation of test specimens and
determination of properties
P/as tiques - Polybuthe (PB) pour moulage et extrusion -
Partie 2: Pr6para tion des 6prouve ttes et d6 termina tion des propri&&
Reference number
IS0 8986-Z: 1995(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 8986-2:1999
IS0 8986-2: 1995(E)
Foreword
IS0 (the international Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 8986-2 was prepared by Technical Committee
lSO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materiak.
IS0 8986 consists of the following parts, under the general title
- Polybutene (PB) moulding and extrusion materials:
P/as tics
- Part 7: Designation system and basis for specifications
- Part 2: Preparation of test specimens and determination of proper-
ties
0 IS0 1995
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
II

---------------------- Page: 8 ----------------------

SIST EN ISO 8986-2:1999
~~
INTERNATIONAL STANDARD 0 IS0 IS0 8986-2: 1995(E)
Plastics - Polybutene (PB) moulding and extrusion
materials -
Part 2:
Preparation of test specimens and determination of
properties
1 Scope 2 Normative references
The following standards contain provisions which,
through reference in this text, constitute provisions
of this part of IS0 8986. At the time of publication, the
This part of IS0 8986 specifies the methods of prep-
editions indicated were valid. All standards are subject
aration of test specimens and the test methods to be
to revision, and parties to agreements based on this
used in determining the properties of PB moulding
part of IS0 8986 are encouraged to investigate the
and extrusion materials. Requirements for handling
possibility of applying the most recent editions of the
test material and for conditioning both the test ma-
standards indicated below. Members of IEC and IS0
terial before moulding and the specimens before
maintain registers of currently valid International
testing are given here.
Standards.
Procedures and conditions for the preparation of test
IS0 62: 1980, Plastics - Determination of water ab-
specimens and procedures for measuring properties
sorption.
of the materials from which these specimens are
made are given. Properties and test methods which
- De termination of tempera-
IS0 75-1: 1993, Plastics
are suitable and necessary to characterize PB mould-
ture of deflection under load - Part I: General test
ing and extrusion materials are listed.
method.
The properties have been selected from the general
IS0 75-2:1993, Plastics - De termination of tempera-
test methods in IS0 10350. Other test methods in
ture of deflection under load - Part 2: Plastics and
wide use for or of particular significance to these
ebonite.
moulding and extrusion materials are also included in
this part of IS0 8986, as are the designatory proper-
IS0 178: 1993, Plastics - Determination of flexural
ties specified in part 1.
properties.
In order to obtain reproducible and comparable test
IS0 179: 1993, Plastics - Determination of Charpy
results, it is necessary to use the methods of speci-
impact strength.
men preparation and conditioning, the specimen di-
IS0 291: 1977, Plastics - Standard atmospheres for
mensions and the test procedures specified herein.
conditioning and testing.
Values determined will not necessarily be identical to
those obtained using specimens of different dimen-
IS0 293: 1986, Plastics - Compression moulding test
sions or prepared using different procedures.
specimens of thermoplastic materials.
1

---------------------- Page: 9 ----------------------

SIST EN ISO 8986-2:1999
Q IS0
IS0 8986-2: 1995(E)
IEC 93:1980, Methods of test for volume resistivity
IS0 527-1:1993, Plastics - Determination of tensile
and surface resistivity of solid electrical insulating
properties - Part I: General principles.
materials.
IS0 527-2:1993, Plastics - Determination of tensile
properties - Part 2: Test conditions for moulding and IEC 112: 1979, Method for determining the compara-
extrusion p/as tics. tive and the proof tracking indices of solid insulating
materials under moist conditions.
IS0 527-4:-J, Plastics - Determination of tensile
Part 4: Test conditions for isotropic and IEC 243-l :I 988, Methods of test for electric strength
properties -
of solid insulating materials - Part I: Tests at power
orthotropic fibre-rein forced p/as tic composites.
frequencies.
IS0 899-l : 1993, Plastics - Determination of creep
behaviour - Part 1: Tensile creep. IEC 250: 1969, Recommended methods for the deter-
mination of the permittivity and dielectric dissipation
IS0 1133:1991, Plastics - Determination of the melt
factor of electrical insulating materials at power, audio
mass-flow rate (MFR) and the melt volume-flow rate
and radio frequencies including metre wavelengths.
(MVR) of thermoplastics.
IEC 296: 1982, Specification for unused mineral insu-
IS0 1183:1987, Plastics - Methods for determining lating oils for transformers and switchgear.
the density and relative density of non-cellular
IEC 1006:1991, Methods of test for
...