SIST EN 12439:2000
(Main)Sterile rectal catheters for single use
Sterile rectal catheters for single use
This European Standard specifies requirements for single-use rectal catheters intended to be inserted into the rectum of a patient, for emptying, rinsing or filling purposes.
Sterile Rektalkatheter zur einmaligen Verwendung
Diese Europäische Norm legt Anforderungen an Rektalkatheter zur einmaligen Verwendung fest. Sie sind dazu bestimmt, transanal in den Darm des Patienten eingeführt zu werden, um diesen zu entleeren, zu spülen oder zu füllen.
Sondes rectales stériles non réutilisables
La présente norme européenne spécifie les exigences relatives aux sondes rectales non réutilisables destinées a etre introduites dans le rectum du patient, aux fins de purge, de rinçage ou de remplissage.
Sterilni rektalni katetri za enkratno uporabo
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sterilni rektalni katetri za enkratno uporaboSterile Rektalkatheter zur einmaligen VerwendungSondes rectales stériles non réutilisablesSterile rectal catheters for single use11.040.25Injekcijske brizge, igle in katetriSy
...
This May Also Interest You
This part of ISO 11608 specifies requirements and test methods for needle-based injection systems with automated functions (referred to in the standard as NIS-AUTO), for the administration of medicinal products in humans. This document does not cover remote communication from the NIS-AUTO.
- Standard30 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft27 pagesEnglish languagesale 10% offe-Library read for×1 day
- Amendment12 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft9 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies requirements and test methods for Needle-Based Injection Systems (NISs)
for single-patient use intended to deliver discrete volumes (bolus) of medicinal product, which can
be delivered through needles or soft cannulas for intradermal, subcutaneous and/or intramuscular
delivery, incorporating pre-filled or user-filled, replaceable or non-replaceable containers.
This document applies in cases where the NIS incorporates a prefilled syringe. However, stand-alone
prefilled syringes defined by ISO 11040-8 are not covered by this document (see exclusions below).
It is important to note that other functions and characteristics of the prefilled syringe, such as dose
accuracy, are subject to the requirements (delivered volume) in ISO 11040-8 and not this document,
unless the addition impacts the delivery function (e.g. a mechanism that intends to restrict or stop
the plunger movement, which would limit the dose delivered). In that case, the system is completely
covered by this document and applicable requirements of the ISO 11608 series.
Excluded from the scope are:
— stand-alone prefilled syringes defined by ISO 11040-8 (with noted exceptions above);
— NISs that provide continuous delivery and require a delivery rate clinically specified in the medicinal
product labelling or determined by a physician based on clinical relevance (i.e. medication efficacy)
as would be the case with insulin patch pumps or traditional infusion pumps (e.g. IEC 60601-2-24,
ISO 28620) associated with continuous delivery of medicinal products (e.g. insulin);
— NISs with containers that can be refilled multiple times;
— requirements relating to methods or equipment associated with user filling of containers unless
they are dedicated accessories (a component necessary for primary function, whether included in
the original kitted product or not);
— NISs intended for dental use;
— NISs intended for different routes of administration (e.g. intravenous, intrathecal, intraocular).
NOTE These products that are excluded might benefit from elements in this document but might not
completely fulfil the basic safety and effectiveness of such products.
- Standard81 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft69 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies requirements and test methods for needle-based injection systems (NISs)
containing electronics with or without software (NIS-Es).
The needle-based injection system containing electronics can be single use or reusable and can be
operated with or without electrical/conductive connections to other devices. The system is intended to
deliver medication to a patient by self-administration or by administration by one other operator (e.g.
caregiver or health care provider).
This document applies to electronic accessories that are intended to be physically connected to a NIS or
NIS-E according to the NIS/NIS-E intended use.
This document also applies to electronic accessories that are intended to have electrical/conductive
connections to a NIS or NIS-E according to the NIS/NIS-E intended use.
This document does not specify requirements for software in programmable NIS-E.
NOTE IEC 60601-1:2005+AMD1:2012+AMD2:2020, Clause 14 addresses software life cycle processes.
This document does not specify requirements for cybersecurity.
- Standard72 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft56 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies requirements and test methods for design verification of containers and
integrated fluid paths used with Needle-Based Injection Systems (NISs) according to ISO 11608-1.
It is applicable to single and multi-dose containers either filled by the manufacturer (primary container
closure) or by the end-user (reservoir) (e.g. cartridges, syringes) and fluid paths that are integrated
with the NIS at the point of manufacture.
This document is also applicable to prefilled syringes (see ISO 11040-8) when used with a NIS (see also
scope of ISO 11608-1:2022).
This document is not applicable to the following products:
— sterile hypodermic needles;
— sterile hypodermic syringes;
— sterile single-use syringes, with or without needle, for insulin;
— containers that can be refilled multiple times;
— containers intended for dental use;
— catheters or infusion sets that are attached or assembled separately by the user
- Standard35 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft31 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies requirements and test methods for single-use, double-ended, sterile needles
intended to be used with some needle-based injection systems (NISs) that use a non-integrated doubleended needle according to ISO 11608-1.
This document is not applicable to the following:
— needles for dental use;
— pre-attached syringe needles;
— hypodermic needles;
— needles intended for different routes of administration (e.g. intravenous, intrathecal, intraocular);
— materials that form the medicinal product contact surfaces of the primary container closure.
However, while this document is not intended to directly apply to these needle products, it does contain
requirements and tests methods that can be used to help design and evaluate them.
NOTE Needles provided by the manufacturer integrated into the fluid path or container are covered in
ISO 11608-3, and hypodermic needles provided separately are covered in ISO 7864.
- Standard40 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft29 pagesEnglish languagesale 10% offe-Library read for×1 day
This document gives requirements for labels attached to syringes so that the contents can be identified just before use during anaesthesia. It covers the colour, size, design and general properties of the label and the typographical characteristics of the wording for the drug name.
NOTE National or regional regulations might require additional labelling, which can include bar coding. No requirements for this additional labelling are given.
- Standard16 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft13 pagesEnglish languagesale 10% offe-Library read for×1 day
2021-06-25 - IEC Corrected version
- Corrigendum3 pagesEnglish and French languagesale 10% offe-Library read for×1 day
This document specifies dimensions and requirements for the design and functional performance of
small-bore connectors intended to be used for connections in intravascular applications or hypodermic
connections in hypodermic applications of medical devices and accessories.
EXAMPLES Hypodermic syringes and needles or intravascular (IV) cannulae with male and female Luer slip
connectors and Luer lock connectors.
NOTE 1 See Annex A.
NOTE 2 The Luer connector was originally designed for use at pressures up to 300 kPa.
This document does not specify requirements for the medical devices or accessories that use these
connectors. Such requirements are given in particular documents for specific medical devices or
accessories.
This document does not specify requirements for the following small-bore connectors, which are
specified in other documents:
— haemodialyser, haemodiafilter and haemofilter blood compartment ports (ISO 8637 [5] and
applicable portion of ISO 8638 [6] referencing blood compartment ports);
— haemodialysis, haemodiafiltration and haemofiltration equipment connectors (ISO 8637 [5]);
— infusion system closure piercing connectors (ISO 8536-4 [4]).
NOTE 3 Manufacturers are encouraged to incorporate the small-bore connectors specified in this document into
medical devices or accessories, even if currently not required by the relevant particular medical device documents.
It is expected that when the relevant particular medical device documents are revised, requirements for smallbore
connectors, as specified in ISO 80369, will be included.
NOTE 4 ISO 80369-1:2018, Clause 7, specifies alternative methods of conformance with ISO 80369-1:2018, for
small-bore connectors intended for use with intravascular applications or hypodermic application medical devices
or accessories, which do not conform with this document.
- Standard55 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft50 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies dimensions and requirements for both open and closed suction catheters made
of flexible materials and intended for use in suctioning of the respiratory tract.
Suction catheters intended for use with flammable anaesthetic gases or agents, lasers or electrosurgical
equipment are not covered by this document.
NOTE For guidance on airway management during laser surgery of the upper airway, see ISO/TR 11991[4].
- Standard32 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft34 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.