SIST EN 3831:2004

Aerospace series - Inserts, thickwall, self-locking, in heat resisting steel FE-PM3801 (17-4PH), MoS2 coated

This standard specifies the characteristics of self-locking, thickwall inserts, in FE-PM3801, MoS2 coated, for aerospace applications.
Maximum test temperature: 350 °C

Aerospace series - Inserts, thickwall, self-locking, in heat resisting steel FE-PM3801 (17-4PH), MoS2 coated

General Information

• Status: Withdrawn
• Publication Date: 30-Apr-2004
• Withdrawal Date: 31-May-2005
• ICS: 49.030.30 - Nuts
• Technical Committee: I08 - Imaginarni 08
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 01-Jun-2005
• Due Date: 01-Jun-2005
• Completion Date: 01-Jun-2005
• Ref Project: EN 3831:2003 - Aerospace series - Inserts, thickwall, self-locking, in heat resisting steel FE-PM3801 (17-4PH), MoS2 coated

Relations

• Replaced By: SIST EN 3831:2005 - Aerospace series - Inserts, thickwall, self-locking, MJ threads, in heat resisting steel FE-PM3801 (17-4PH), MoS2 coated
• Effective Date: 01-Jun-2005

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Inserts, thickwall, self-locking, in heat resisting steel FE-PM3801 (17-4PH), MoS2 coatedAerospace series - Inserts, thickwall, self-locking, in heat resisting steel FE-PM3801 (17-4PH), MoS2 coated49.030.30MaticeNutsICS:Ta slovenski standard je istoveten z:EN 3831:2003SIST EN 3831:2004en01-maj-2004SIST EN 3831:2004SLOVENSKI
STANDARD



SIST EN 3831:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3831January 2003ICS 49.030.30English versionAerospace series - Inserts, thickwall, self-locking, in heatresisting steel FE-PM3801 (17-4PH), MoS2 coatedThis European Standard was approved by CEN on 2 June 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3831:2003 ESIST EN 3831:2004



EN 3831:2003 (E)2ContentspageForeword.30Introduction.31Scope.32Normative references.33Required characteristics.43.1Configuration – Dimensions- Tolerances – Masses.43.2Material.43.3Surface treatment.44Insert definition.44.1Nominal size insert.54.2Repair size insert.65Designation.66Marking.77Technical specification.7SIST EN 3831:2004



EN 3831:2003 (E)3ForewordThis document (EN 38
...