oSIST prEN 1463-3:2020
(Main)Road marking materials - Part 3: Active road studs: performance requirements
Road marking materials - Part 3: Active road studs: performance requirements
This European standard specifies requirements, performance parameters and test methods for active road studs intended for use as permanent and temporary road marking materials. Requirements and test methods for induction, fibre optic or other power transmission systems for active road studs are not included in this standard.
Straßenmarkierungsmaterialien - Markierungsknöpfe - Teil 3: Selbstleuchtende Markierungsknöpfe
Dieses Dokument legt die Produktmerkmale, die Laborprüfverfahren, die Art und Weise der Angabe von Ergebnissen und die relevanten Verfahren für die Bewertung und Überprüfung der Leistungsbeständigkeit von aktiven Markierungsknöpfen (siehe 3.1) für die Verwendung als dauerhafte Markierungen, Abgrenz-ungen und Signalisierungen auf Verkehrsflächen fest.
Dieses Dokument behandelt:
- aktive Markierungsknöpfe ohne Retroreflektor, die Licht in weißer, roter, gelber/oranger, grüner und blauer Farbe ausstrahlen;
- aktive Markierungsknöpfe mit weißen, gelben, orangen, roten und grünen Retroreflektor(en);
- unabhängige aktive Markierungsknöpfe (Mittel zur Energieversorgung werden in diesem Dokument nicht behandelt);
- festverdrahtete aktive Markierungsknöpfe (Mittel zur Licht- oder Energiezufuhr werden in diesem Dokument nicht behandelt);
- aktive Markierungsknöpfe mit einer oder mehreren leuchtenden Oberflächen;
- aktive Markierungsknöpfe, die Licht ausstrahlen, das vom menschlichen Auge als konstant oder mit niedriger Frequenz blinkend wahrgenommen wird;
- aktive Markierungsknöpfe, die entweder auf die Straßenoberfläche geklebt oder in diese eingelassen oder eingebettet sind;
- aktive Markierungsknöpfe, die eindrückbar oder nicht eindrückbar sind.
Produkte, die für Nennspannungen über 50 V Wechselspannung bzw. über 75 V Gleichspannung ausgelegt sind, werden in diesem Dokument nicht behandelt. Die Spannungsangaben beziehen sich auf die Eingangs- oder Ausgangsspannungen, nicht auf Spannungen, die im Inneren des Geräts auftreten können.
Produits de marquage routiers - Partie 3 : Plots actifs : exigences de performance
Le présent document spécifie les caractéristiques des produits, les méthodes d’essai en laboratoire, la manière d’exprimer les résultats et les procédures correspondantes pour l’évaluation et la vérification de la constance des performances des plots actifs (voir 3.1), destinés à être utilisés pour les marquages routiers permanents, à des fins de délimitation et de signalisation dans les zones de circulation.
Ce document couvre les aspects suivants :
- plots actifs dépourvus de rétroréflecteur(s), émettant de la lumière de couleur blanche, rouge, jaune/orange, orange, verte ou bleue ;
- plots actifs équipés d’un ou de plusieurs rétroréflecteurs de couleur blanche, jaune, orange, rouge ou verte ;
- plots actifs autonomes (les sources d’alimentation électrique ne sont pas traitées dans le présent document) ;
- plots actifs câblés (les sources de lumières ou d'énergie ne sont pas traitées dans le présent document) ;
- plots actifs possédant une ou plusieurs faces lumineuses ;
- plots actifs émettant une lumière qui semble constante à l’œil humain ou qui clignote à basse fréquence ;
- plots actifs qui sont fixés à la chaussée par liaison, insertion ou intégration ;
- plots actifs ayant ou non la capacité d’être enfoncés.
Le présent document ne couvre pas les produits conçus avec une tension nominale supérieure à 50 V en courant alternatif ou supérieure à 75 V en courant continu. Les tensions nominales se réfèrent à la tension de l’entrée ou de la sortie électrique, et non aux tensions qui peuvent être présentes à l’intérieur de l’équipement.
Materiali za označevanje vozišča - 3. del: Odsevniki: zahtevane lastnosti
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 1463-3:2020
01-marec-2020
Materiali za označevanje vozišča - 3. del: Odsevniki: zahtevane lastnosti
Road marking materials - Part 3: Active road studs: performance requirements
Straßenmarkierungsmaterialien - Markierungsknöpfe - Teil 3: Selbstleuchtende
Markierungsknöpfe
Produits de marquage routiers - Partie 3 : Plots actifs : exigences de performance
Ta slovenski standard je istoveten z: prEN 1463-3
ICS:
93.080.20 Materiali za gradnjo cest Road construction materials
oSIST prEN 1463-3:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 1463-3:2020
---------------------- Page: 2 ----------------------
oSIST prEN 1463-3:2020
DRAFT
EUROPEAN STANDARD
prEN 1463-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2020
ICS 93.080.20
English Version
Road marking materials - Part 3: Active road studs:
performance requirements
Straßenmarkierungsmaterialien - Markierungsknöpfe -
Teil 3: Selbstleuchtende Markierungsknöpfe
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 226.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1463-3:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Product characteristics . 7
4.1 Visibility characteristics expressed as day and night-time visibility . 7
4.1.1 Night-time visibility (only for retroreflecting active road studs) . 7
4.1.2 Luminance (for day and night-time visibility) expressed as light output (cd) . 8
4.1.3 Chromaticity coordinates (x,y) (for day and night-time visibility) . 8
4.2 Light output frequency . 9
4.3 Electrical safety . 9
4.4 Electromagnetic compatibility . 9
4.5 Ingress protection (IP code) . 9
4.6 Durability on road trials . 9
5 Testing, assessment and sampling methods . 9
5.1 Test of light output (luminous intensity cd) . 9
5.2 Test of Chromaticity coordinates (x,y) (for day and night-time visibility) . 11
5.3 Test of light output flashing frequency . 11
5.4 Ingress protection (IP code) . 11
5.5 Test of durability on road trials . 11
6 Assessment and verification of constancy of performance – AVCP. 12
6.1 General . 12
6.2 Type testing . 12
6.2.1 General . 12
6.2.2 Test samples, testing and compliance criteria . 13
6.2.3 Test reports . 13
6.3 Factory production control (FPC) . 14
6.3.1 General . 14
6.3.2 Requirements . 14
6.3.3 Product specific requirements . 16
6.3.4 Initial inspection of factory and of FPC . 17
6.3.5 Continuous surveillance of FPC . 18
6.3.6 Procedure for modifications . 18
6.3.7 One-off products, pre-production products (e.g. prototypes) and products produced
in very low quantity . 18
Annex ZA (informative) Relationship of this European Standard with Regulation (EU) No.
305/2011 . 20
ZA.1 Scope and relevant characteristics . 20
ZA.2 System of Assessment and Verification of Constancy of Performance (AVCP) . 21
ZA.3 Assignment of AVCP tasks . 21
Bibliography . 23
2
---------------------- Page: 4 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
European foreword
This document (prEN 1463-3:2020) has been prepared by Technical Committee CEN/TC 226 “Road
equipment”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a standardization request given to CEN by the European
Commission and the European Free Trade Association, and supports basic work requirements of
Regulation (EU) Nr. 305/2011.
For relationship with Regulation (EU) 305/2011, see informative Annexe ZA, which is an integral part of
this document.
3
---------------------- Page: 5 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
Introduction
The development of this document has been prompted by the appearance of road studs which contain an
active element which emits light instead of, or as well as, reflecting light from headlights.
4
---------------------- Page: 6 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
1 Scope
This document specifies the initial and the retained performance requirements and laboratory test
methods for solar powered, hardwired and communicating active road studs intended for use as
permanent road marking materials.
In accordance with Low Voltage Directive 2014/35/EU, product characteristic electrical safety is
applicable only to those active road studs which are designed with voltage rating between 50 and 1 000 V
for alternating current and between 75 and 1 500 V for direct current. Voltage ratings refer to the voltage
of the electrical input or output, not to voltages that may appear inside the equipment.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1463-1:2009, Road marking materials - Retroreflecting road studs - Part 1: Initial performance
requirements
EN 1463-2:2000, Road marking materials - Retroreflecting road studs - Part 2: Road test performance
specifications
EN 60529:1991, Degrees of protection provided by enclosures (IP Code)
EN 50293:2012, Road traffic signal systems - Electromagnetic compatibility
EN 60598-1:2015, Luminaires - Part 1: General requirements and tests
EN 60598-2-13:2006, Luminaires - Part 2-13: Particular requirements - Ground recessed luminaires
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1463-1 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
active road stud
horizontal guiding device that is fixed to the surface of a road and emits light in order to warn, guide or
inform road users
Note 1 to entry: An active road stud provides a light output by itself, while a retroreflective road stud provides
retroreflected light when illuminated by the headlamps of a vehicle. Retroreflective road studs are covered by
EN 1463-1:2009.
Note 2 to entry: An active road stud can be fitted with a retroreflector so that it provides a light output both
directly and by retroreflection.
Note 3 to entry: An active road stud can be self-contained in the sense that it incorporates all light generation
means and does not rely on an external source of light or power. Light generation means include one or more light
sources, typically LED’s, and a power supply, typically a battery that is charged by a solar panel integrated in the
upper surface of the road stud.
5
---------------------- Page: 7 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
Note 4 to entry: As opposed to a self-contained active road stud, an active road stud can also be hardwired in the
sense that it receives light through fibre optics or power through a wire. Means to feed light or power are not
considered in this document.
Note 5 to entry: An active road stud can have one or more luminous faces intended for emitting light in one or
more traffic directions.
Note 6 to entry: An active road stud can emit light that appears constant to the human eye or be flashing at a low
frequency. The emitted light can be any of the colours white, yellow/amber, red, green or blue.
Note 7 to entry: As with a retroreflective road stud, an active road stud can be fixed to a road surface by being
bonded to, entered within or embedded within the road surface. Additionally, an active road stud can be depressible
or non-depressible.
3.2
luminance expressed as light output (cd)
for the purpose of this document the term luminance expressed as light output (cd) is used to describe
luminous intensity measured in cd
3.3
chromaticity co-ordinates (x,y)
chromaticity coordinates of the colours are defined in accordance with the CIE 1931 Standard
Colorimetric 2° Observer as referenced in CIE 15
Note 1 to entry: For the purpose of this standard colours white, red, yellow/amber, orange, green and blue are
defined using chromaticity coordinates of corner points of chromaticity regions for emitted radiation as specified
in Table 1 and outlined in Figure 1.
Table 1 — Corner points of chromaticity regions for emitted radiation
Colour coordinates of corner points
Colour
1 2 3 4
x 0,300 0,440 0,440 0,300
White
y 0,342 0,432 0,382 0,276
x 0,660 0,680 0,710 0,690
Red
y 0,320 0,320 0,290 0,290
x 0,536 0,547 0,613 0,593
Yellow/Amber
y 0,444 0,452 0,387 0,387
x 0,624 0,605 0,650 0,669
Orange
y 0,370 0,370 0,331 0,331
x 0,009 0,284 0,209 0,028
Green
y 0,720 0,520 0,400 0,400
x 0,109 0,173 0,208 0,148
Blue
y 0,087 0,160 0,125 0,025
6
---------------------- Page: 8 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
Key
1 white
2 red
3 yellow/amber
4 orange
5 green
6 blue
Figure 1 — Chromaticity regions for emitted radiation of active road studs
4 Product characteristics
4.1 Visibility characteristics expressed as day and night-time visibility
4.1.1 Night-time visibility (only for retroreflecting active road studs)
Retro-reflectivity for night-time visibility (only for retroflecting active road studs) expressed as
Coefficient of Luminous Intensity (R’) is provided in EN 1463-1:2009, 5.3.
7
---------------------- Page: 9 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
4.1.2 Luminance (for day and night-time visibility) expressed as light output (cd)
The light output (luminous intensity cd) of an active road stud is described by the minimum luminous
intensities supplied by each luminous face of the active road stud in a number of directions defined by a
horizontal and a vertical angle. These directions shall cover reference direction and at least combinations
of the two angles as given in Table 2. Additionally, the light output is described by the maximum luminous
intensity supplied by each luminous face of the active road stud in any direction. Reference direction is
given by manufacturer.
Table 2 — Combinations of horizontal (H) and vertical (V) angles for measurement of luminous
intensity
Direction Angle combination in (°)
Horizontal −15 −10 −7 −5 −2 0 2 5 7 10 15
2,67 1,83 — 1 0,5 0 0,5 1 — 1,83 2,67
Vertical 10 6 — 3 2 0,5 2 3 — 6 10
— — 7 4 — 2 — 4 7 — —
3
4
6
7
10
When light is emitted in pulses in periods of less than 0,5 s, the luminous intensities are to be understood
as effective luminous intensities I calculated using the Blondell-Rey Formula (1):
eff
t
2
I(t)dt
∫
t
1
(1)
I =
eff
0,2+(tt- )
2 1
where
t , t are time instants at which I(t) = I .
2 1 eff
NOTE When light is emitted only within a time interval Δt and I(t) is constant at I within that time interval, Ieff
can be determined by:
It× Δ
I =
eff
0,2+ Δt
The declared values shall be tested in accordance with 5.1.
4.1.3 Chromaticity coordinates (x,y) (for day and night-time visibility)
When tested in accordance with 5.2, the emitted radiation of each luminous face of an active road stud
shall be described by measured chromaticity coordinates (x,y) and declared as either of the colours white,
red, yellow/amber, orange, green or blue.
Chromaticity coordinates (x,y) of retro-reflected light (only for retroflecting active road studs) are
provided in EN 1463-1:2009, 5.3.
8
---------------------- Page: 10 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
4.2 Light output frequency
Active road studs can emit light in pulses/flashes. The lowest flashing frequency of the light emitted is
determined as the number of pulses per minute and expressed in Hz. The lowest flashing frequency of
the light emitted shall be measured in accordance with 5.3.
4.3 Electrical safety
Active road studs with input or output voltages between 50 and 1 000 V for alternating current and
between 75 and 1 500 V for direct current shall conform to EN 60598-1:2015 when tested in accordance
with EN 60598-2-13:2006.
4.4 Electromagnetic compatibility
Active road studs shall conform to EN 50293:2012 when tested in accordance with EN 50293:2012,
Clause 7 for electromagnetic emission and EN 50293:2012, Clause 8 for electromagnetic immunity.
4.5 Ingress protection (IP code)
Protection against dust and water shall be declared in accordance with EN 60529 and tested in
accordance with 5.4.
4.6 Durability on road trials
The durability of retro-reflectivity for night-time visibility of retroflecting active road studs is tested after
road trials in accordance with EN 1463-2. During this test, the retroflecting active road studs need not
have any light output.
The durability of the following characteristics of active road studs shall be tested after a road trial in
accordance with 5.5:
— Luminance (for day and night-time visibility) expressed as Light output (Cd) declared in accordance
with 4.1.2 in reference direction.
— Chromaticity coordinates (x,y), for night-time declared in accordance with 4.1.3.
— Light output frequency (Hz declared in accordance with 4.2.
The characteristics are measured both before and after exposure to the road trial.
5 Testing, assessment and sampling methods
5.1 Test of light output (luminous intensity cd)
A luminous face of an active road stud is assigned a reference centre and a reference direction, which
points against the traffic direction intended for that luminous face.
The active road stud is mounted in a goniometer such as shown in Figure 2, with the reference centre in
the rotation centre of the goniometer and the reference direction pointing along the optical bench
towards a photometer.
The photometer is placed at such a distance D between the locations 1 and 4 in Figure 2 that neither the
luminous face nor the receptive surface of the photometer exceeds 10’ (minutes of arc) as seen from that
distance.
9
---------------------- Page: 11 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
Key
1 rotation centre of goniometer
2 horizontal angle
3 vertical angle
4 photometer
Figure 2 — Goniometer and optical bench with a photometer
The goniometer is placed in a darkened room with an ambient temperature of 25 °C. If operated on
integral storage, the active road stud is fully charged in accordance with the manufacturer’s instructions.
If hardwired, the active road stud is supplied in accordance with the manufacturer’s instructions.
The light output (luminous intensity cd) in a particular direction is obtained by this procedure:
a) the desired horizontal and vertical angles from reference direction are set;
b) the illuminance E in lux (lx) with the active road stud turned off is recorded;
0
c) the illuminance E in lux (lx) with the active road stud turned on is recorded;
2
d) the light output (luminous intensity cd) in candela (cd) is determined by I = (E - E ) × D .
0
An initial warm up time in accordance with the manufacturer’s instructions shall be allowed in order to
obtain stable measurements.
10
---------------------- Page: 12 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
5.2 Test of Chromaticity coordinates (x,y) (for day and night-time visibility)
The set up for test of chromaticity of the emitted light is done in the same way as for the test of the light
output (luminous intensity cd) as described in 5.1 but using a colourimeter instead of a photometer.
The chromaticity coordinates are obtained by this procedure:
a) the reference direction is set;
b) the chromaticity coordinates are recorded;
An initial warm up time in accordance with the manufacturer’s instructions shall be allowed in order to
obtain stable measurements
5.3 Test of light output flashing frequency
Flashing frequency shall be measured using a suitable timing device to determine the total number of
complete on/off cycles in one minute.
5.4 Ingress protection (IP code)
Declarations of protection against dust and water shall be tested in accordance with EN 60529:1991,
Clause 13 and 14.
5.5 Test of durability on road trials
The durability of the following characteristics is tested on road trials:
— Luminance (for day and night-time visibility) expressed as Light output (cd) tested in accordance
with 5.1. Only reference direction is used for testing.
— Chromaticity coordinates (x,y), for night-time visibility tested in accordance with 5.2.
— Light output flashing frequency (Hz) tested in accordance with 5.3.
This test needs to involve only 10 active road studs emitting white light, and only measurement of the
light output and the chromaticity coordinates in reference direction.
Application of active road studs on test site shall be in accordance with the instructions of the
manufacturer. During this test, the active road studs need not have any light output.
NOTE 1 For example, in case of hard-wired active road studs it is not necessary to power and operate the road
studs during the road trial.
The volume of traffic shall be such as to ensure that at least three active road studs are exposed to
minimum 200 000 wheel passages.
A road trial shall include at least one full climatic cycle of one year.
NOTE 2 Special requirements (e.g. snow clearance, studded tyres) considered indispensable for some countries
or special applications, may be taken into account by the participating parties for the selection of the test site and
recorded in the general report for the test site.
11
---------------------- Page: 13 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
6 Assessment and verification of constancy of performance – AVCP
6.1 General
The compliance of active road studs with the requirements of this standard and with the performances
declared by the manufacturer in the DoP shall be demonstrated by:
— determination of the product type;
— factory production control by the manufacturer, including product assessment.
The manufacturer shall always retain the overall control and shall have the necessary means to take
responsibility for the conformity of the product with its declared performance(s).
6.2 Type testing
6.2.1 General
All performances related to characteristics included in this standard shall be determined when the
manufacturer intends to declare the respective performances unless the standard gives provisions for
declaring them without performing tests. (e.g. use of previously existing data, CWFT and conventionally
accepted performance).
Assessment previously performed in accordance with the provisions of this standard, may be taken into
account provided that they were made to the same or a more rigorous test method, under the same AVCP
system on the same product or products of similar design, construction and functionality, such that the
results are applicable to the product in question.
NOTE 1 Same AVCP system means testing by an independent third party, under the responsibility of a notified
product certification body.
For the purposes of assessment, the manufacturer's products may be grouped into families, where it is
considered that the results for one or more characteristics from any one product within the family are
representative for that same characteristics for all products within that same family
NOTE 2 Products may be grouped in different families for different characteristics.
Reference to the assessment method standards should be made to allow the selection of a suitable
representative sample.
In addition, the determination of the product type shall be performed for all characteristics included in
the standard for which the manufacturer declares the performance:
— at the beginning of the production of a new or modified active road stud (unless a member of the
same product range), or
— at the beginning of a new or modified method of production (where this may affect the stated
properties); or
they shall be repeated for the appropriate characteristic(s), whenever a change occurs in the active road
stud design, in the raw material or in the supplier of the components, or in the method of production
(subject to the definition of a family), which would affect significantly one or more of the characteristics.
Where components are used whose characteristics have already been determined, by the component
manufacturer, on the basis of assessment methods of other product standards, these characteristics need
not be re-assessed. The specifications of these components shall be documented.
12
---------------------- Page: 14 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
Products bearing regulatory marking in accordance with appropriate harmonized European
specifications may be presumed to have the performances declared in the DoP, although this does not
replace the responsibility on the active road stud manufacturer to ensure that the active road stud as a
whole is correctly manufactured and its component products have the declared performance values.
6.2.2 Test samples, testing and compliance criteria
The number of samples of active road studs to be tested/assessed shall be in accordance with Table 3.
Table 3 — Number of samples to be tested and compliance criteria
Assessment No. of Compliance
Characteristic Requirement
method samples criteria
Retroreflectivity and 4.1.1 Annex A and B of 3 5.3 of
colourimetry for night-time EN 1463-1:2009 EN 1463-1:2009
visibility of retroreflectors
(only for retroreflective
active road studs)
Luminance (for day and 4.1.2 5.1 3 4.1.2
night-time visibility)
expressed as light output
(cd)
Chromaticity coordinates 4.1.3 5.2 3 4.1.3
(x,y) (for day and night-time
visibility)
Light output frequency 4.2 5.3 3 4.2
Electrical safety 4.3 to 1 EN 60598-1:2015
EN 60598-2-13:2006
Electromagnetic 4.4 to EN 50293:2012 1 EN 50293:2012
compatibility Clause 7 and 8
Ingress of dust and water 4.5 5.4 1 4.5
Durability on road trials 4.6 EN 1463-2:2000 50 4.6
(only for retroreflective retroreflective
active road studs) active road
studs
Durability on road trials 4.6 5.5 10 4.6
6.2.3 Test reports
The results of the determination of the product type shall be documented in test reports. All test reports
shall be retained by the manufacturer for at least 10 years after the last date of production of the active
road studs to which they relate.
13
---------------------- Page: 15 ----------------------
oSIST prEN 1463-3:2020
prEN 1463-3:2020 (E)
6.3 Factory production control (FPC)
6.3.1 General
The manufacturer shall establish, document and maintain an FPC system to ensure that the products
placed on the market comply with the declared performance of the essential characteristics.
The FPC system shall consist of procedures, regular inspections and tests and/or assessments and the
use of the results to control raw and other incoming materials or components, equipment, the production
process and the product.
All the elements, requirements and provisions adopted by the manufacturer shall be documented in a
systematic manner in the form of written policies and procedures.
This factory production control system documentation shall ensure a common understanding of the
evaluation of the constancy of performance and enable the achievemen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.